The Chili – 30+GH/s BFL based Bitcoin Miner Assembly

[jelin1984]

32 bit windows version

[Bargraphics]

32 bit windows version

That would be your reason,

That versions for 64bit windows, I just went and made a 32 Bit for you

http://www.speedyshare.com/vgRJy/BFGMiner-Chili-32.zip

This is a workaround version of BFGMiner until a new firmware update for the chilis

Here's a modified version of BFGMiner, I also included the driver inside of it as well that should fix your problem. (I don't know much about CGMiner though)

http://www.speedyshare.com/vgRJy/BFGMiner-Chili-32.zip

Open up bfgminer.conf and change the Pool and Username to whatever you want (It currently uses mine so make sure you change it)
Run CDM v2.08.30 WHQL Certified.exe to install the correct driver for windows

Once you do both of those, just open up bfgminer.exe and it should read from the config automatically and start hashing for you.
If it doesn't see the Chili, all you have to do is keep BFGMiner open, unplug the USB, Plug it back in, press M then + then type all or auto and enter. It should find it.

Please note if it still isn't working then you need to exit BFGMiner, unplug you chili power, plug it back in and wait for all the lights to stop blinking. If you try to find the miner while it's "Booting up" it will have issues.
"Booting Up" is the two most right LEDs (Closer to the Power) blinking back and forth. Again once all the LEDs are not blinking anymore it should be ready to start hashing, start your BFGMiner and follow the above steps.

Let me know if this helps

[jelin1984]

ok it started
will see
when you will have new firmware updated?

[jelin1984]

do you have any version for linux?
rasperby

i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh

why that happen?

[MrTeal]

do you have any version for linux?
rasperby

i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh

why that happen?

28GH/s is pretty low, I would try reseating the heat sink. You still haven't replied as to what heat sink you are using, so I can't help you there.

[jelin1984]

i have artic twin turbo 2

what i must do at miner with hashing 28gh

[MrTeal]

i have artic twin turbo 2

what i must do at miner with hashing 28gh

Did you try reseating the heat sink to make sure you have good contact?

[ranmn7]

watching

[jelin1984]

which is the correct and incorrect Fujipoly     SIDE
Fujipoly Extreme Thermal Pad

I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
?

[MrTeal]

which is the correct and incorrect Fujipoly     SIDE
Fujipoly Extreme Thermal Pad

I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
?

Can you post a close-up picture of what you're talking about, preferably still on the board?

Thanks.

[jelin1984]

http://www.frozencpu.com/products/image/11631/thr-84.jpg/thr-84/Fujipoly_Premium_System_Builder_Thermal_Pad_-_14_Sheet_-_150_x_100_x_05_-_Thermal_Conductivity_60_WmK.html


if you see the photo you see that one side have some like square and the other side of thermal pad does not

which side go where
which go SIDE GO TO HEATSINK OF COOLER?

[MrTeal]

http://www.frozencpu.com/products/image/11631/thr-84.jpg/thr-84/Fujipoly_Premium_System_Builder_Thermal_Pad_-_14_Sheet_-_150_x_100_x_05_-_Thermal_Conductivity_60_WmK.html


if you see the photo you see that one side have some like square and the other side of thermal pad does not

which side go where
which go SIDE GO TO HEATSINK OF COOLER?

Yes, but can you take a picture of it on your board as you have it mounted?

[jelin1984]

OK THESE IS CORRECT OR THE SECOND PHOTO IS CORRECT?

[MrTeal]

The shiny bumpy part is the plastic that protects the thermal pad in transit. You should take it off.

[jelin1984]

yes i will take off
but which of the 2 photo is correct?
first or second??

[MrTeal]

yes i will take off
but which of the 2 photo is correct?
first or second??

It shouldn't matter.

[jelin1984]

ok i will try again and let you know the hashing of the second one the first is 35 gh
the second is somewhere between 28-30 gh

[suprabitz]

i have 1 chili i havent even set up. ordered these chips before i got out of mining

if anyone wants it i will do $650 (via bitcoin) shipped. you can contact Mr Teal and he will verify that he shipped me one.

Escrow with John K is ok if you pay the fees.

ready to ship - no wait

[Spieder]

Mr. Teal,

Since you guys were so successful on this project, any thoughts on whether or not your considering a group buy for your own custom chips or another version of the Chili using an existing chip?

[Keefe]

The shiny bumpy part is the plastic that protects the thermal pad in transit. You should take it off.

There is plastic on both sides that must be taken off. One side is bumpy, one side is smooth. Remove both.