[JCE]Fast & stable CN/v8/Heavy/Tube/XHV miner, CPU+GPU, Vega56 1800+ RX580 1200+

[polsska]

3x RX 550 2GB (core 1315MHz, mem 2050MHz), Driver 18.10.2, Windows 10 1809
XMR v8

07:43:27 | Hashrate GPU Thread 0: 246.37 h/s
07:43:27 | Hashrate GPU Thread 1: 256.64 h/s - Total GPU 0: 503.01 h/s
07:43:27 | Hashrate GPU Thread 2: 246.37 h/s
07:43:27 | Hashrate GPU Thread 3: 249.34 h/s - Total GPU 2: 495.70 h/s
07:43:27 | Hashrate GPU Thread 4: 240.69 h/s
07:43:27 | Hashrate GPU Thread 5: 250.77 h/s - Total GPU 3: 491.46 h/s
07:43:27 | Total: 1490.16 h/s - Max: 1490.16 h/s

conf

"gpu_threads_conf" :
[
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 0, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 0, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 2, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 2, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 3, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 3, "multi_hash":432 },
]

[UnclWish]

3x RX 550 2GB (core 1315MHz, mem 2050MHz), Driver 18.10.2, Windows 10 1809
XMR v8

07:43:27 | Hashrate GPU Thread 0: 246.37 h/s
07:43:27 | Hashrate GPU Thread 1: 256.64 h/s - Total GPU 0: 503.01 h/s
07:43:27 | Hashrate GPU Thread 2: 246.37 h/s
07:43:27 | Hashrate GPU Thread 3: 249.34 h/s - Total GPU 2: 495.70 h/s
07:43:27 | Hashrate GPU Thread 4: 240.69 h/s
07:43:27 | Hashrate GPU Thread 5: 250.77 h/s - Total GPU 3: 491.46 h/s
07:43:27 | Total: 1490.16 h/s - Max: 1490.16 h/s

conf

"gpu_threads_conf" :
[
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 0, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 0, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 2, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 2, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 3, "multi_hash":432 },
     { "mode" : "GPU", "worksize" : 16, "alpha" : 64, "beta" : 8, "gamma" : 8, "delta" : 8, "epsilon" : 8, "zeta" : 8, "index" : 3, "multi_hash":432 },
]

You can lower worksize to 8. It can increase speed.

[polsska]

You can lower worksize to 8. It can increase speed.

When I use 8 I have a drop

Hashrate GPU Thread 0: 195.38 h/s
08:42:45 | Hashrate GPU Thread 1: 179.61 h/s - Total GPU 0: 374.98 h/s
08:42:45 | Hashrate GPU Thread 2: 169.73 h/s
08:42:45 | Hashrate GPU Thread 3: 195.38 h/s - Total GPU 2: 365.10 h/s
08:42:45 | Hashrate GPU Thread 4: 185.62 h/s
08:42:45 | Hashrate GPU Thread 5: 180.80 h/s - Total GPU 3: 366.42 h/s
08:42:45 | Total: 1106.50 h/s - Max: 1144.25 h/s

[Lno]

what is the config for vega56? 5*vega56 = 8500
on srb 9100

[smparo]

Can someone share a working configuration (gpu and mem clock/v and config) for v8 for rx580 8Gb/4Gb?
On v6-v7 I have made a configurations but with v8 I'm unable to get one that stay stable!!! 
Actualy I'm on 1150gpu/2000mem/850mv and

{ "mode" : "GPU", "worksize" : 8, "alpha" : 64, "beta" : 8, "index" : X, "multi_hash":1696 }    for 8Gb (doublethread)
{ "mode" : "GPU", "worksize" : 8, "alpha" : 64, "beta" : 8, "index" : X, "multi_hash":944 }      for 4Gb (doublethread)

Whit this configuration I can get 950h/s on 0.33b4

I also did some test for bittube but also here I don't reached a stable configuration!
The system sometimes crash during the job (the card that goes into error changes almost every time) other times the miner start and stop immediately after connection with the pool (for this problem I think a problem with a card but it don't write which card goes wrong).

For all this problem I create this scheduled task procedure (win10): if something goes wrong the system restart itself (on startup I have the bat that start a miner process, usually or your or phoenixminer)

Code:

@ECHO OFF

rem exit

SETLOCAL EnableExtensions
set EXE=jce_cn_gpu_miner64.exe
FOR /F %%x IN ('tasklist /NH /FI "IMAGENAME eq %EXE%"') DO IF %%x == %EXE% goto FOUND

set EXE=PhoenixMiner.exe
FOR /F %%x IN ('tasklist /NH /FI "IMAGENAME eq %EXE%"') DO IF %%x == %EXE% goto FOUND

set EXE=SRBMiner-CN.exe
FOR /F %%x IN ('tasklist /NH /FI "IMAGENAME eq %EXE%"') DO IF %%x == %EXE% goto FOUND

echo Mining process is not running, restarting windows...
ping 127.0.0.1 -n 30 > nul
shutdown /r /t 60

goto END

:FOUND
echo %EXE% is running
ping 127.0.0.1 -n 3 > nul
goto QUIT

:END
ping 127.0.0.1 -n 5 > nul
rem pause

:QUIT
exit

[JCE-Miner]

Please give the full command line you used so I can understand. Just replace your wallet (parameter -u) by XXX to stay anonymous

./start.sh --archi skylake -o XXXXXXX -u XXXXXXXXXXX -p X -c config.txt

Got it, --archi is a hint for the --auto mode, since you use the manual config, you cannot use it

Code:

"cpu_threads_conf" : 
[ 
     { "cpu_architecture" : "auto", "affine_to_cpu" : 0, "use_cache" : true, "multi_hash":2 },
     { "cpu_architecture" : "auto", "affine_to_cpu" : 1, "use_cache" : true, "multi_hash":2 },
     ....
     { "cpu_architecture" : "auto", "affine_to_cpu" :23, "use_cache" : true, "multi_hash":2 },
]

See the "auto" tokens in my example? That's where you can put "skylake" instead.
But the performance change will be null or negligible on such a fast CPU, the manual architecture has an impact on slow CPUs like Core2 or Athlon. Better keep "auto".

Lermite kindly provided optimal config for RX570, it may be good on RX580 too.
Using 100% memory is good for CN-Heavy but not always for CN-v8

RX570 4G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
]

RX570 8G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
]

[Pencila]

Can anybody share the config setting for AMD R9 290 for CNV8?

[BluePowder]

GPU thread

Do you have any miner for Linux at the moment ??  I have a few 7970 cards but only have ubuntu 14-16 as OS.

[UnclWish]

Lermite kindly provided optimal config for RX570, it may be good on RX580 too.
Using 100% memory is good for CN-Heavy but not always for CN-v8

RX570 4G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
]

RX570 8G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
]

For my 2 RX 580 8G cards best multi_hash parameters for v8 are multiples of 96. Such as 1104, 1200 etc. Higher - speeder. Best is 1680, 1776 and 1872.

[adaseb]

I read the last few pages and couldn't find any info but anyone here manage to run the Tahiti or the Hawaii GPUs with this miner?

The Tahiti being the 7950 7970 280X and Hawaii being 290 390 295

So far the Pitcairn speeds are impressive basically what I get with my Tahiti with XMR Stak.

[smparo]

Lermite kindly provided optimal config for RX570, it may be good on RX580 too.
Using 100% memory is good for CN-Heavy but not always for CN-v8

RX570 4G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
]

RX570 8G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
]

For my 2 RX 580 8G cards best multi_hash parameters for v8 are multiples of 96. Such as 1104, 1200 etc. Higher - speeder. Best is 1680, 1776 and 1872.

If I can ask, which value do you have set for gpu MHz, mem MHz and voltage?
Now I'm on 1680 for multihash (above this value after some time it crash...) and 1150MHz/2000MHz/850mv for GPU setting... since a couple of hours it works without crashing  
I'm getting in the same card from 910 to 960MH/s... I do not understand, however, why the value move up and down so much

[JCE-Miner]

Breaking change

When I started JCE-GPU, my competitors where SRB and Claymore. The JCE fees were aligned with SRB (0.9%) on purpose.
Now the game has changed, Claymore is obsolete and the lead in performances is TeamRed. I'm getting on-par with him on v8, but i still lacked a decent implementation for Heavy-class to completely outperform SRB, leave it behind and have only one real competitor. I'm like Stalin, i avoid having two opponents at the same time.

Dedicated to UnclWish who asked for it for a long time, here comes...

JCE GPU 0.33b5 with +20% performance on Heavy/Haven/Tube

Tested on both HD7000 and RX cards, with perfs in the range +15% to +25%
My HD7950 jumped from 335 to 415, my RX560 from 340 to 400

The bad news is that the fees are now aligned with TeamRed, at 2.1% (still a bit below their 2.5%) but only on Heavy-class algos, where the extra perf deserve them. On CN and CN-light, that's still 0.9%. If mixed with CPU, it's a weighted average, as before.

0.33b5 GPU

Huge performance boost for Heavy/HVX/Tube
Respective fees increased to 2.1%
Very light perf boost for CN-v8

[heavyarms1912]

0.33b5 GPU
Huge performance boost for Heavy/HVX/Tube
Respective fees increased to 2.1%
Very light perf boost for CN-v8

Still get the same abort

Abort was called at 348 line in file:
d:\qb\workspace\19992\src\vpg-compute-neo\runtime\os_interface\windows\wddm\wddm.cpp

EDIT: Nvm just read that iGPU are detected too now.  Had to change gpu indexes in config file.

[JCE-Miner]

https://github.com/jceminer/cn_gpu_miner/blob/master/README.md#troubleshooting
last question

You have an Intel IPG/GPU in your computer, don't you?

Do you have any miner for Linux at the moment ??  I have a few 7970 cards but only have ubuntu 14-16 as OS.

For CPU yes, but not GPU, and this is very unlikely regarding how little time i can allow to Linux versions. Even the CPU versions are less often updated than the Windows ones.

[heavyarms1912]

https://github.com/jceminer/cn_gpu_miner/blob/master/README.md#troubleshooting
last question

You have an Intel IPG/GPU in your computer, don't you?

yea i was reading notes.  Figured that out.  was editing my own post .

[UnclWish]

Breaking change

When I started JCE-GPU, my competitors where SRB and Claymore. The JCE fees were aligned with SRB (0.9%) on purpose.
Now the game has changed, Claymore is obsolete and the lead in performances is TeamRed. I'm getting on-par with him on v8, but i still lacked a decent implementation for Heavy-class to completely outperform SRB, leave it behind and have only one real competitor. I'm like Stalin, i avoid having two opponents at the same time.

Dedicated to UnclWish who asked for it for a long time, here comes...

JCE GPU 0.33b5 with +20% performance on Heavy/Haven/Tube

Tested on both HD7000 and RX cards, with perfs in the range +15% to +25%
My HD7950 jumped from 335 to 415, my RX560 from 340 to 400

The bad news is that the fees are now aligned with TeamRed, at 2.1% (still a bit below their 2.5%) but only on Heavy-class algos, where the extra perf deserve them. On CN and CN-light, that's still 0.9%. If mixed with CPU, it's a weighted average, as before.

0.33b5 GPU

Huge performance boost for Heavy/HVX/Tube
Respective fees increased to 2.1%
Very light perf boost for CN-v8

Ok, thanx! Let's try new version... Settings is the same as in prev versions, I hope...

[vmozara]

Tested with my home pc, easily pulled 1800h/s with 1400 core /1100 mem vega 64 with following:
 { "mode" : "GPU", "worksize" : 8, "alpha" : 128, "beta" : 8, "gamma" : 8, "delta" : 4, "epsilon" : 4, "zeta" : 4, "index" : 0, "multi_hash":960 },
 { "mode" : "GPU", "worksize" : 8, "alpha" : 128, "beta" : 8, "gamma" : 8, "delta" : 4, "epsilon" : 4, "zeta" : 4, "index" : 0, "multi_hash":960 },

The consumption of the card seemed far less than cn v8. Probably 2000 can be reached with proper tuning of the card.

however i can not test any further, as i just managed to have my rigs running smoothly and tomorrow I am embarking the ship for next 30 days. This ground breaking update comes 1 or 2 days too late for me, I could have switched the rigs to heavy algo and save some power. Now it is too risky for me for testing - any trouble and i can not repair my rigs for 30 days. Well, next time!

JCE, great work! see, you can do anything, just need some motivation!

[Coindgr]

I read the last few pages and couldn't find any info but anyone here manage to run the Tahiti or the Hawaii GPUs with this miner?

The Tahiti being the 7950 7970 280X and Hawaii being 290 390 295

So far the Pitcairn speeds are impressive basically what I get with my Tahiti with XMR Stak.

                                 
Anyone?
How much you get with 280x?

[vmozara]

JCE, you should edit the topic name to contain miner version, and also big news like this, to attract more people

[matheus176]

Please give the full command line you used so I can understand. Just replace your wallet (parameter -u) by XXX to stay anonymous

./start.sh --archi skylake -o XXXXXXX -u XXXXXXXXXXX -p X -c config.txt

Got it, --archi is a hint for the --auto mode, since you use the manual config, you cannot use it

Code:

"cpu_threads_conf" : 
[ 
     { "cpu_architecture" : "auto", "affine_to_cpu" : 0, "use_cache" : true, "multi_hash":2 },
     { "cpu_architecture" : "auto", "affine_to_cpu" : 1, "use_cache" : true, "multi_hash":2 },
     ....
     { "cpu_architecture" : "auto", "affine_to_cpu" :23, "use_cache" : true, "multi_hash":2 },
]

See the "auto" tokens in my example? That's where you can put "skylake" instead.
But the performance change will be null or negligible on such a fast CPU, the manual architecture has an impact on slow CPUs like Core2 or Athlon. Better keep "auto".

Lermite kindly provided optimal config for RX570, it may be good on RX580 too.
Using 100% memory is good for CN-Heavy but not always for CN-v8

RX570 4G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 0, "multi_hash": 976 },
]

RX570 8G

Code:

"gpu_threads_conf": 
[ 
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
  { "mode": "GPU", "worksize": 8, "alpha": 64, "beta": 8, "index": 1, "multi_hash": 1008 },
]

oh i tried without --archi but it´s the same error, i don´t know what´s happening the miner is using multi hash but only x2 and even with x2 there´s 16mb l3 cache left for the 20 threads and 8mb for the 24 threads i want to try x3 but the -c parameter always gives this error.