Walking Glitch
Sr. Member
Offline
Activity: 252
Merit: 250
Amateur Professional
|
|
January 31, 2014, 06:54:55 PM |
|
though it hasn't been a long test, I'm officially against antiminer ... antminer is much better.
Don't you wish all such problems were so easy to fix? Try building a Windows QT wallet sometime when you need a challenge... +1 Monkey and I must have copied the typo from the same place. Actually, I did the same thing day 1. It seems the problem typo is original in the bfgminer literature on antminers.. I haven't checked, but from reading this thread anyway. So make sure your .bat says antminer not antiminer lol also the icarus stuff makes sense and helps getting over the 2gh wall (provided you are giving enough power and cooling etc) I can get a couple to 2.1 with it no prob without hardware mods. I'm 99.9% certain it was a typo in the original bfgminer documentation, as I also had this problem at first.
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 01, 2014, 09:06:03 PM |
|
After reading all this thread and learn, now I have 2 AntMiners working at 3.0 Gh. With out of the box AntMiner, step by step i change the clock parameter to 0881 (1.8Gh), after that value i collect many HW errors, so i add R2 10K and change R1 with 3.3K (dismounted from a cd drive board). Now all the errors disappear but the ant miner became really hot, i mount it on a dissipator (2.9 °C/W) dismounting the original one leaving the rubber and smearing thermal silicone grease, the coil also was hot (50°C). http://i58.tinypic.com/34fbjvo.jpgNow the ant miner works without errors till 0A81 (2.2 Gh). Pushing up the frequency the coil and the asic increase their heat. At this point i decide to dissipate also this heat. I cut a piece of aluminium and another squared piece for the asic (8x8 mm and 2mm thick) for equilibrate the different heights of coil and chip. http://i57.tinypic.com/zvg2d.jpgRemember to put always thermal silicone grease. http://i58.tinypic.com/wrc2mw.jpgNow i try to increase the frequency till 4E81 (3.0 Gh) without HW errors. http://i62.tinypic.com/359aelc.jpgAfter all i discover that also the power chip is hot (70 °C), so decide to put a little piece of aluminium with grease on top of it glued (cyanoacrylate) on the aluminium. http://i62.tinypic.com/nv4ino.jpgI use an UsbHub with 4A power supply limited at 1A for each port, but the real voltage on usb ports is 4.52 Volts. The software is BFGMINER 3.10.0 and the OS is Open Suse. I insert also inside the conf the icarus-timing with the right Hs value extracted launching miner.php on the web server (Apache 2). Now for me is enough. Thanks all. My bfgminer.conf { "pools" : [ { "url" : "stratum+tcp://stratum.bitcoin.cz:3333", "user" : "user.user", "pass" : "xxxxxx", "pool-priority" : "0" }, { "url" : "stratum+tcp://us1.eclipsemc.com:3333", "user" : "user.user", "pass" : "yyyyyy", "pool-priority" : "1" } ] , "api-listen" : true, "api-mcast-port" : "4028", "api-port" : "4028", "expiry" : "120", "expiry-lp" : "3600", "log" : "5", "no-pool-disable" : true, "no-show-processors" : true, "no-show-procs" : true, "no-unicode" : true, "queue" : "2", "scan-time" : "60", "skip-security-checks" : "0", "submit-stale" : true, "temp-hysteresis" : "3", "shares" : "0", "kernel-path" : "/usr/local/share/bfgminer", "scan" : [ "antminer:all" ], "set-device" : [ "antminer:clock=x4E81" ], "api-allow" : "W:192.168.1.0/24", "icarus-options" : "115200:2:2", "icarus-timing" : "0.153" }
http://i62.tinypic.com/30w3z48.jpg
|
|
|
|
chromosoma
|
|
February 01, 2014, 09:36:16 PM |
|
Hm, interesting. Did you try to run more Antimners on one hub? I can also achieve about 2,7 GHS with two mines on one USB Hub, but when i add more they just stop working, or work at much lower ghs rate.
|
|
|
|
chromosoma
|
|
February 01, 2014, 11:08:37 PM |
|
But my cooling solution is better:)) Active cooling with PC controlled Fan:) Indeed low temp increase stability and performance:)
|
|
|
|
twindragon6
Newbie
Offline
Activity: 15
Merit: 0
|
|
February 02, 2014, 02:41:32 AM Last edit: February 02, 2014, 03:17:00 AM by twindragon6 |
|
Very nice! I'm still waiting on my other two then I'll upload a shot or two. Also, can I use any old capacitor on these? I have a bag of 2200µF 25V ones I'm not using, or would that be overkill and possibly fry things?
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 02, 2014, 07:27:27 AM |
|
Hm, interesting. Did you try to run more Antimners on one hub? I can also achieve about 2,7 GHS with two mines on one USB Hub, but when i add more they just stop working, or work at much lower ghs rate.
I have only two ant miner actually. My Hub voltage output is limited to 1A (written on the box) and power supply is 4A for 4 ports. The usb voltage drop to 4.52, means that ant drain more than 1A, i didn't measure the current. The next step will be to open the hub and cut + and - wire (the external one of the usb connector) and connect them directly to the main wires of the power supply without the limitation of the chip. Doing this you can use all the power without limitations and the maximum number of ant become 3 for this hub.
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 02, 2014, 07:40:46 AM |
|
But my cooling solution is better:))
Active cooling with PC controlled Fan:)
Indeed low temp increase stability and performance:)
Yes GREAT in any sense!! Did you measure the coil, asic and AOZ1021A temperature ? Are they hot ? which resistance value do you use for R1 (2.49 K)?
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 02, 2014, 08:19:38 AM |
|
Hm, interesting. Did you try to run more Antimners on one hub? I can also achieve about 2,7 GHS with two mines on one USB Hub, but when i add more they just stop working, or work at much lower ghs rate.
Do you know how is the circuit of your hub ? One of mine had 9V 2A p.supply but internally for have 5V use one 7805 that is able to give .5A or 1.5A with a good dissipator, with this is impossible to have more than 1.5A totally. I bought a new one, in the photo, with 5V 4A ps, without internal regulator, means that the current is regulated only by the usb interface (1A) that i'll try to jump over today.
|
|
|
|
chromosoma
|
|
February 02, 2014, 11:58:39 AM |
|
Hi, i measured the Temperature on my 2K2&10K Modes @ 2GHS Main ASIC: 45 °C Coil: 38 °C DC/DC converter: 45 °C Ambient temperature : 22 °C Fan Speed at 45% --------------------------------------- I don't use a hub, i am using USB3.0 PCI extension card, which is powered directly through my PSU.My PSU can provide up to 25 Amp on 5V rail. Still i also have voltage drop on my miners to around 4,2-4,1 V if i connect more then 2 Miners at once. Which is not good.The funy thing is, that input voltage on my PCI card remains stable at 5,2V. So the problem is on PCI Card itself. I am also thinking of connecting 5V rail directly to the USB PORT, avoiding everything on the board. Maybe i will do it today. Surely it will void all the safety like polyfuses and overvoltage protection, but i am engineer,i am allowed:)))
|
|
|
|
chromosoma
|
|
February 02, 2014, 03:48:02 PM |
|
Success! =) After moding my PCI card by connecting the power directly to the 5V input i managed to get very good results:) Of course now i dont have any USB protection, so if anything happens, i rely on the internal fuse in PSU:) Now i am running all 4 miners at 4C81 Configuration. On higher frequency i get HW. Maybe if i replace 2,2K resistor with higher value i could run it at 4GHS:) But since I dont want to push them to the limits....:9 I will observe them at this configuration for the next few days:) The temperatures are now a bit higher, like 5°C more then values in previous post.
|
|
|
|
Janezki
Member
Offline
Activity: 85
Merit: 10
|
|
February 02, 2014, 06:20:08 PM |
|
chromosoma, you're connected to 127.0.0.1, is that somekind of testmode or are you mining solo? 4C81 is 2.6Gh/s, do the Ants keep that 2.7-2.8Gh/s speed or do they fall to 2.6G in the long run or when connected to a pool/server? Normally the hashrate is in par or slightly under what the clockspeed is set to, probably because of the workload & network speed.
I have 4 Ants now volt (5v from 30A PSU) & cap modded and stuck to an XBox360 GPU cooler. Three of them can run together at 2.675Gh/s max. with clock=x3506, one can't pass 2.0Gh/s no matter what I do, HW errors will go through the roof...
|
BCLambovXNggZSCruBycAApon17qTkcr9F
|
|
|
chromosoma
|
|
February 02, 2014, 06:43:08 PM |
|
Hi, yes, i am mining solo. Since it is altcoin (goatcoin) it is still possible. While mining bitcoins on btcguild pool i get something about 9,5 GHS. But other pools can give much better results. After running miners for about a hour the hashrate stabilizes around 2,6-2,6 GHS Did you also changed the resitors on your miners? Sometimes the soldering joint is not good, maybe try to resolder R's on those 2.0 GHS Antminer
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 02, 2014, 07:20:28 PM |
|
Success! =) After moding my PCI card by connecting the power directly to the 5V input i managed to get very good results:) Of course now i dont have any USB protection, so if anything happens, i rely on the internal fuse in PSU:)
Now i am running all 4 miners at 4C81 Configuration. On higher frequency i get HW. Maybe if i replace 2,2K resistor with higher value i could run it at 4GHS:) But since I dont want to push them to the limits....:9 I will observe them at this configuration for the next few days:) The temperatures are now a bit higher, like 5°C more then values in previous post.
Me too, on my hub i jump the 5V current limitations soldering a wire on it. http://i58.tinypic.com/2ngg35t.jpgChanged also the R2 to 4.7K and now I can use 5081 without HW errors, i put also two fans.
|
|
|
|
simgambu
Newbie
Offline
Activity: 6
Merit: 0
|
|
February 03, 2014, 06:47:50 AM Last edit: February 03, 2014, 11:26:26 AM by simgambu |
|
I "sang too early", my two ants work at 5081 but in few hours one of them every hour delays the response of shares reaching 0.6 Gh really (the third number). So only one is able to work till 5081 (after that value many HW errors) and my actual configuration is 4F81.
|
|
|
|
doctormandrake
|
|
February 03, 2014, 07:17:43 AM |
|
Success! =) After moding my PCI card by connecting the power directly to the 5V input i managed to get very good results:) Of course now i dont have any USB protection, so if anything happens, i rely on the internal fuse in PSU:) Now i am running all 4 miners at 4C81 Configuration. On higher frequency i get HW. Maybe if i replace 2,2K resistor with higher value i could run it at 4GHS:) But since I dont want to push them to the limits....:9 I will observe them at this configuration for the next few days:) The temperatures are now a bit higher, like 5°C more then values in previous post. hi, would you mind terribly posting your .bat file for bfgminer and your .conf for goatcoin? I am having trouble getting solo mining running with bfgminer (no problem on cgminer) and would like very much to compare my settings to someone who has solo mining running on bfgminer. thank you.
|
|
|
|
chromosoma
|
|
February 03, 2014, 07:37:38 AM |
|
Sure: .bat bfgminer -o http://127.0.0.1:12646 -u goat -p abcd --set-device antminer:clock=x4C81 -S antminer:all
.conf addnode=69.90.132.127 rpcport=12646 rpcpassword=abcd rpcuser=goat server=1
|
|
|
|
doctormandrake
|
|
February 03, 2014, 07:02:52 PM |
|
Sure: .bat bfgminer -o http://127.0.0.1:12646 -u goat -p abcd --set-device antminer:clock=x4C81 -S antminer:all
.conf addnode=69.90.132.127 rpcport=12646 rpcpassword=abcd rpcuser=goat server=1 Thank you, do not know what the problem is. I even downloaded goat and recreated your settings, worked fine on cgminer (modified for that of course) and still no luck on bfgminer. I am just using p2p or pools for now with said coins, since the hashrate loss on cgminer isn't worth the solo mining gains (altho since I set it up I put goat into my multiminer mix now ^^ ) Have a great day
|
|
|
|
pumawolf
|
|
February 04, 2014, 08:14:49 PM |
|
im getting unexpected command argument when runing .bat file, what am i doing wrong
bfgminer.exe –set-device antminer:clock=x0981 -o stratum+tcp//us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
bfgminer.exe –set-device antminer:clock=x0981 -o us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
i uses these so far and btcguild, i dont think its a url ,user ,password issue.
|
|
|
|
BRADLEYPLOOF
|
|
February 04, 2014, 08:36:07 PM |
|
im getting unexpected command argument when runing .bat file, what am i doing wrong
bfgminer.exe –set-device antminer:clock=x0981 -o stratum+tcp//us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
bfgminer.exe –set-device antminer:clock=x0981 -o us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
i uses these so far and btcguild, i dont think its a url ,user ,password issue.
use two dashes for set-device. it should look like --set-device antminer:clock=x0981
|
|
|
|
pumawolf
|
|
February 04, 2014, 10:09:48 PM |
|
im getting unexpected command argument when runing .bat file, what am i doing wrong
bfgminer.exe –set-device antminer:clock=x0981 -o stratum+tcp//us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
bfgminer.exe –set-device antminer:clock=x0981 -o us1.ghash.io:3333 -u 1122.ghash -p 123 -S antminer:all
i uses these so far and btcguild, i dont think its a url ,user ,password issue.
use two dashes for set-device. it should look like --set-device antminer:clock=x0981 thanks man , im really bad with tech stuff. does the overclockin run better on bfg 3.10 or the nwo 3.9
|
|
|
|
|