[ANN] [MINT] Mintcoin (POS / 5%) [NO ICO] [Fair distro, community maintained]

[majorminers]

Mining is not dead yet! Just hit another block for 219842.5 MINT - http://mint.majorminers.com/

Difficulty is only getting harder, so mine some now.

[brokedummy]

is there a guide how to setup mintcoin cgminer? I don't get it there's no config file? I have a 4.0.0 version

I'm not new to mining.

You need version 3.7.2. Scrypt isn't supported in later versions.

http://ck.kolivas.org/apps/cgminer/

which one is the correct one then?

He don't support it anymore. You have to either have 3.7.2 zip already or dl from other source.

[atcsecure]

Hashrate through the roof!

[jany8293]

I shall sell them at 100 satoshis, so that will still take quite some time

Crap coins like Kittehcoin that have 100 billion units hit 50 Satoshi.  After mint mining is over, there will be 20 billion coins out vs Kittehcoin's current 7 billion.  Assuming Mint was as horrible as Kittehcoin, which it's not, it would hit 17 Satoshi in the near future.  Assuming it was better, then 20+ Satoshi in the next week or two is easily possible.  Factor in block rewards going to nothing, that should increase exchange demand as well.

The last comparison is obviously Dogecoin.  I would give mint a conservative rock bottom peak of 50 Satoshi within a month or two.  It could catch on, go higher, and reach that 100+ level though.  If mint totally bombed out for whatever reason, and was worse than every coin except Cagecoin, it's still going to go to at least 30.  30 is worst case scenario.  All it has to do to hit 50 is match what the PoW clone coins have hit.

Agreed, +1!

[amacar]

A little bit out of context...

What is best and most reliable service to convert BTC to fiat, preferably EUR?

I entered Crypto world through ebay and mining, now I have to withdraw to buy some daily food

Thanks in advance!

I am using kraken.com. It is fast and reliable over SEPA.

[bluewhackadoo]

Can't believe I overlooked this one on launch.  Lot to like here, took a small position last night, best of luck to you early adopters.

[sakkosekk]

is there a guide how to setup mintcoin cgminer? I don't get it there's no config file? I have a 4.0.0 version

I'm not new to mining.

You need version 3.7.2. Scrypt isn't supported in later versions.

http://ck.kolivas.org/apps/cgminer/

which one is the correct one then?

http://ck.kolivas.org/apps/cgminer/3.7/

as he said, you need cgminer 3.7.2

[majorminers]

Can't believe I overlooked this one on launch.  Lot to like here, took a small position last night, best of luck to you early adopters.

It's definitely not too late to get in. We're at the very early stages of adoption and growth.

The new website will be unveiled tomorrow (I believe) - which will help boost Mintcoin's appeal.

MINT is an energy saving/interest bearing Bitcoin alternative!

[Degolep]

is there a guide how to setup mintcoin cgminer? I don't get it there's no config file? I have a 4.0.0 version

I'm not new to mining.

You need version 3.7.2. Scrypt isn't supported in later versions.

http://ck.kolivas.org/apps/cgminer/

which one is the correct one then?

http://ck.kolivas.org/apps/cgminer/3.7/

as he said, you need cgminer 3.7.2

http://cryptomining-blog.com/tag/gpu-mining/page/3/

got it from here but still don't know whats wrong just wont start correctly

[jany8293]

Help with the promotion guys,

http://redd.it/1yih05

Also, don't forget to vote for MINT @

Allcrypt: http://www.allcrypt.com/beta/voting.php
CoinedUp: http://www.reddit.com/r/CoinedUp/comments/1xk8ge/please_add_mintcoin/
CryptX: http://www.reddit.com/r/CryptX/comments/1xxkow/please_add_mintcoin/
SwissCEX: https://swisscex.uservoice.com/forums/238010-general/suggestions/5488394-add-mint-coin

Stay Fresh!

Voting, done!

[sakkosekk]

is there a guide how to setup mintcoin cgminer? I don't get it there's no config file? I have a 4.0.0 version

I'm not new to mining.

You need version 3.7.2. Scrypt isn't supported in later versions.

http://ck.kolivas.org/apps/cgminer/

which one is the correct one then?

http://ck.kolivas.org/apps/cgminer/3.7/

as he said, you need cgminer 3.7.2

http://cryptomining-blog.com/tag/gpu-mining/page/3/

got it from here but still don't know whats wrong just wont start correctly

what does your .bat file look like? And what kinda GPU are you using?

[thejepper]

so i'm waiting for the markets to cool down a little bit, amazing amount of trading volume for a new coin though!
probably will be back with lows to 10-12 end of this weekend.

[sakkosekk]

so lets wait for the markets to cool down a little bit
probably will be back with lows to 10-12 end of this weekend.

Yup, and a new mean of 10-12 instead of 3-4 satoshi is incredible

[Degolep]

is there a guide how to setup mintcoin cgminer? I don't get it there's no config file? I have a 4.0.0 version

I'm not new to mining.

You need version 3.7.2. Scrypt isn't supported in later versions.

http://ck.kolivas.org/apps/cgminer/

which one is the correct one then?

http://ck.kolivas.org/apps/cgminer/3.7/

as he said, you need cgminer 3.7.2

http://cryptomining-blog.com/tag/gpu-mining/page/3/

got it from here but still don't know whats wrong just wont start correctly

what does your .bat file look like? And what kinda GPU are you using?

I have a .conf file

{
"pools" : [
   {
      "url" : "stratum+tcp://mnt.coins4everyone.com",
      "user" : "user",
      "pass" : "pass"
   }
]
,
"intensity" : "13",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"lookup-gap" : "2",
"thread-concurrency" : "8192",
"shaders" : "2048,",
"gpu-engine" : "0-0",
"gpu-fan" : "0",
"gpu-memclock" : "0",
"gpu-memdiff" : "0",
"gpu-powertune" : "0",
"gpu-vddc" : "0.000",
"temp-cutoff" : "75",
"temp-overheat" : "85",
"temp-target" : "65",
"api-port" : "4028",
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "2",
"hotplug" : "5",
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "60",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"
}

2x 280x

[sakkosekk]

I have a .conf file

{
"pools" : [
   {
      "url" : "stratum+tcp://mnt.coins4everyone.com",
      "user" : "user",
      "pass" : "pass"
   }
]
,
"intensity" : "13",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"lookup-gap" : "2",
"thread-concurrency" : "8192",
"shaders" : "2048,",
"gpu-engine" : "0-0",
"gpu-fan" : "0",
"gpu-memclock" : "0",
"gpu-memdiff" : "0",
"gpu-powertune" : "0",
"gpu-vddc" : "0.000",
"temp-cutoff" : "75",
"temp-overheat" : "85",
"temp-target" : "65",
"api-port" : "4028",
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "2",
"hotplug" : "5",
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "60",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"
}

2x 280x

hmm, I can't see anything wrong. I am no expert though, I run cgminer with .bat(your way is more "pro")

[Degolep]

i've had .bat also but can't find it anymore....

[hostmaster]

MINT giveaway continues
who wants to get free 50 MINTs?

go for it here http://ecoiner.org/giveaways/50-mint-mintcoin-giveaway-leave-address-919/

[atcsecure]

How can we monitor PoS mining? any commands through debug/console that we can use?

[atcsecure]

How is PoS interest applied/calculated?

[Alty]

Hey guys I know allot of people are waiting to see a nice new shiny website for Mintcoin.

Here is my work in progress so far.

It is not fully functional yet and still adding lot's of things but because we are a community, please feel free to check out the work in progress and perhaps give me some feedback and I'll see what I can do! 

http://mintcoin.cc