WildRig Multi 0.40.9 multi-algo miner with low dev-fee (AMD/NVIDIA/INTEL)

[melloyellow]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

[andrucrypt]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

[melloyellow]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

R9 290 (4Gb) = 12-13 MH/s

What clocks and volts do you run your 290s and 390s at? 

[melloyellow]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

Nicehash    256M

The rejects don't happen all the time.  Could it be the person that 'rented' my hash pointed it to a bad pool?
Would a newer driver work better?

[andrucrypt]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

Nicehash    256M

The rejects don't happen all the time.  Could it be the person that 'rented' my hash pointed it to a bad pool?
Would a newer driver work better?

Looks I have found the reason. Job target should be all 256 bits, not just 64 bit I check. Will fix that in next release. But this is not critical, since miner shouldn't send this solutions anyway. What about drivers, I prefer good old one 18.3.4 or 18.6.1

[melloyellow]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

Nicehash    256M

The rejects don't happen all the time.  Could it be the person that 'rented' my hash pointed it to a bad pool?
Would a newer driver work better?

Looks I have found the reason. Job target should be all 256 bits, not just 64 bit I check. Will fix that in next release. But this is not critical, since miner shouldn't send this solutions anyway. What about drivers, I prefer good old one 18.3.4 or 18.6.1

I'm using 19.2     I don't think the miner is sending the solutions, it disconnects, then recompiles the kernel.  Then the rejects start over again.

[melloyellow]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

Nicehash    256M

The rejects don't happen all the time.  Could it be the person that 'rented' my hash pointed it to a bad pool?
Would a newer driver work better?

Looks I have found the reason. Job target should be all 256 bits, not just 64 bit I check. Will fix that in next release. But this is not critical, since miner shouldn't send this solutions anyway. What about drivers, I prefer good old one 18.3.4 or 18.6.1

I'm using 19.2     I don't think the miner is sending the solutions, it disconnects, then recompiles the kernel.  Then the rejects start over again.

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

[cjwallsg]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

R9 290 (4Gb) = 12-13 MH/s

What clocks and volts do you run your 290s and 390s at? 

For both 390 and 290 downvolted -25mv. Core clocks 1100 for 390s and 1000 for 290s

[Chef22]

So I am trying to change the dev fee while mining BCX and it will not switch from 2 %. Also, why does the dev pool mine for 2 minutes every 1 and a half hours? That's a lot more than 2 %

[andrucrypt]

So I am trying to change the dev fee while mining BCX and it will not switch from 2 %. Also, why does the dev pool mine for 2 minutes every 1 and a half hours? That's a lot more than 2 %

For different shitcoins I left 2%(will update first post). And dev pool mine not every 1:30, but every 98 minutes in this case. Simple math 98 + 2 = 100

[andrucrypt]

0.24.0 beta
-added parameter --progpow-kernel(1 or 2 can give better hashrate on different drivers or gpu configuration)
-speedup ProgPow/KawPow up to 10% on pre-Navi gpu's

Compare different --progpow-kernel values(1 or 2) in benchmark(on KawPow add --benchmark --benchmark-epoch 170 on ProgPowZ try --benchmark --benchmark-epoch 17)

Kernel 2 is great for Vega 56's with 19.2 drivers around 19mh/s but I got too many Share Above Target rejects with Send Stale Shares activated.  I turned send stale shares off and it seems to work fine. Is this expected behavior?

edit: As soon as I posted that, I started getting rejects for Share Above Target.

what pool it is? Difficulty?

Nicehash    256M

The rejects don't happen all the time.  Could it be the person that 'rented' my hash pointed it to a bad pool?
Would a newer driver work better?

Looks I have found the reason. Job target should be all 256 bits, not just 64 bit I check. Will fix that in next release. But this is not critical, since miner shouldn't send this solutions anyway. What about drivers, I prefer good old one 18.3.4 or 18.6.1

I'm using 19.2     I don't think the miner is sending the solutions, it disconnects, then recompiles the kernel.  Then the rejects start over again.

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Hmmm, now this is too weird. Does this happen with pools or just NiceHash? And can you show logs or do you remember the diff that miner show near the "new job" message?

ps: testing here kernel 2 for more than hour on RX590 and drivers 20.2.1 on NiceHash and have no problems...

[Chef22]

So I am trying to change the dev fee while mining BCX and it will not switch from 2 %. Also, why does the dev pool mine for 2 minutes every 1 and a half hours? That's a lot more than 2 %

For different shitcoins I left 2%(will update first post). And dev pool mine not every 1:30, but every 98 minutes in this case. Simple math 98 + 2 = 100

Ok so it will remain 2% ? All good if so, miner works great

[andrucrypt]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

[melloyellow]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

[cjwallsg]

The kernel number "0" is the best kernel for my 290s and 390s for now.

[melloyellow]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

Tested at 2miners and it worked fine.  Went back to nicehash and it works fine.  I guess the z-enemy dev got in touch with them.

Nice work on 0.24.1, I got a little speed boost.

[melloyellow]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

Tested at 2miners and it worked fine.  Went back to nicehash and it works fine.  I guess the z-enemy dev got in touch with them.

Nice work on 0.24.1, I got a little speed boost.

Well, the problem came back.  Could it be that the nicehash buyer is pointing it at a bad pool or doesn't know how to set it up?

[cjwallsg]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

Tested at 2miners and it worked fine.  Went back to nicehash and it works fine.  I guess the z-enemy dev got in touch with them.

Nice work on 0.24.1, I got a little speed boost.

Well, the problem came back.  Could it be that the nicehash buyer is pointing it at a bad pool or doesn't know how to set it up?

Hello, I suggest to mine directly RVN in RavenMiner Pool, using Static Diff. I was mining the first days in nicehash and the avg hashrate was 20% under the displayed in the WildRig miner console. Now in mining in the pool the hashrate is almost 100% of displayed by miner.

[melloyellow]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

Tested at 2miners and it worked fine.  Went back to nicehash and it works fine.  I guess the z-enemy dev got in touch with them.

Nice work on 0.24.1, I got a little speed boost.

Well, the problem came back.  Could it be that the nicehash buyer is pointing it at a bad pool or doesn't know how to set it up?

I just noticed at the nicehash site that it says I don't have xnsub activated, yet I did not put "--no-extranonce" in my bat...

[melloyellow]

0.24.1 beta
- fixed broken non-progpow algorithms
- progpow-kernel now set to 2 for Vega
- tune up slightly progpow kernel 2

I think I misled you about the amount of rejects, it's pretty much all of them.  I can't use kernel 2 at all the way it is now.  I'm stuck using kernel 0 or 1 which give me about 14 mh/s.  A hotfix would be greatly appreciated, you have the only public stable AMD kapow miner.

Looks like NiceHash sending weird seed phrase sometimes(read it from z-enemy dev), and maybe this is a reason of your problem. Right now I have no idea what can I do here, but will look into it.

That's interesting, but I haven't noticed it the problem with my 290 machines.  I'll test a different pool, then I'll try different drivers, and report back.

Tested at 2miners and it worked fine.  Went back to nicehash and it works fine.  I guess the z-enemy dev got in touch with them.

Nice work on 0.24.1, I got a little speed boost.

Well, the problem came back.  Could it be that the nicehash buyer is pointing it at a bad pool or doesn't know how to set it up?

Hello, I suggest to mine directly RVN in RavenMiner Pool, using Static Diff. I was mining the first days in nicehash and the avg hashrate was 20% under the displayed in the WildRig miner console. Now in mining in the pool the hashrate is almost 100% of displayed by miner.

Yes I should be doing that, and may switch to it, but I'm just a little too busy now.  Maybe I should focus on that.