Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
March 09, 2021, 04:05:01 PM |
|
I tried bos-toolbox install -p password 10.10.10.10 but I get this error: [2021-02-28 20:40:13] INFO:Attempting unlock host on 10.10.10.10 with AntPwn v3... [2021-02-28 20:40:13] INFO:Sending upgrade payload... [2021-02-28 20:40:14] INFO:Triggering payload... [2021-02-28 20:40:14] ERROR:Failed to trigger payload on remote!
Do you maybe know what causes this error? This error happens with 2019 firmware before July. Just upgrade your miner first.
Does anyone have the braiinos link for dragonminer T1? I have 5 units and I would like to install it since I have it installed in antminer s9 and it is very efficient
T1 support was dropped in 2019, its not recommended.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
|
|
|
|
There are several different types of Bitcoin clients. The most secure are full nodes like Bitcoin Core, but full nodes are more resource-heavy, and they must do a lengthy initial syncing process. As a result, lightweight clients with somewhat less security are commonly used.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
kano
Legendary
Offline
Activity: 4466
Merit: 1800
Linux since 1997 RedHat 4
|
|
March 16, 2021, 01:30:52 AM |
|
Interesting that they claim to copyright a page that I wrote about half of it
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
March 17, 2021, 04:11:40 PM |
|
Interesting that they claim to copyright a page that I wrote about half of it Or the link to Con Kolivas cgminer's github page.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
Fujitsu
Newbie
Offline
Activity: 10
Merit: 0
|
|
March 20, 2021, 08:48:50 PM Last edit: March 21, 2021, 11:29:33 PM by frodocooper |
|
Guys does anyone know how to properly roll back from this version (Tue Jul 30 20:37:39 CST 2019) to this (Thu May 16 15:51:14 CST 2019) version? i got error while trying to flash it.
|
|
|
|
DigitalCreep
Newbie
Offline
Activity: 8
Merit: 0
|
|
March 21, 2021, 02:48:41 PM Last edit: March 21, 2021, 11:29:12 PM by frodocooper |
|
Hello , Wow, it's been awhile. Would like to say what's up to everybody! Started this whole mining thing around 16'-17' for awhile, life changed and miners got disconnected. Few months ago, decided to check on some old pools, that mining I did years ago actually made me some coin. Decided to sell my old S3+, picked up a S9i at a pretty good price compared to prices now. Ok, i see users stating they are getting something like 10.5TH@755W on various forums out of Braiins OS+ with S9's. Could someone please explain how? For example, Set my Power Limit to 800W, settings are default w/AutoTuning & ASIC Boost Enabled. I get 8.3-8.5TH@755W. Settings presently are 10.42TH@993W. Looking for any links or info to learn more about low voltage mode and how to obtain those settings mentioned above. Thanks for any info and knowledge.
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
March 23, 2021, 02:14:07 AM |
|
Every miner, every hashboard performs differently. Specific power limits will provide different results even with identical models, this is because the chips themselves all have varying qualities, and the autotuning algorithm will find out the best way to use each of them, which is why the process takes its due time.
So if you see someone with an excellent result, it doesn't mean you will get the exact same result using the same value. Especially if the other person has, for example, the S9j 14.5 and you have a vanilla S9 13.
The only thing you can do is experiment different values to find the best efficiency your specific miner can make. You have to wait for the Tuner Status to show Stable before measuring.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
Bitcguru77
Jr. Member
Offline
Activity: 48
Merit: 14
|
|
March 30, 2021, 06:30:05 PM |
|
Hi.
I'm running BOS+ from SD card on a single S9 13,5 THs version.
I've tried different Autotuning settings and so far it seems to run most efficient (taking into count profability) at 1000 W setting (930-935 W measured at the wall) and then mining ~12,15 THs.
Edit: Obviously always tuning until it shows "Stable"
I have the miner in a not yet insulated garage and outside temp is app. 5oC.
I've noticed that the miner performs differently when rebooted at different temperatures. Usually it performs better at warmer temperatures.
Because of this I'm wondering if it would perform even better if i rebooted it and retuned at a higher temperature. However when once tuned at 1000 W the settings are stored and the only way I can get it to retune is to choose another W-setting.
Is there a way to reset the tuning at 1000 W or is the way to go to retune at 999 or 1001 W?
It has now been tuned at 100 W-steps from 800-1600 W and I would not like to reset all autotune settings at once.
Regards. Steff
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
April 03, 2021, 06:00:42 AM |
|
To delete the profiles just do the following from the miner's UI:
Quick Actions, stop bosminer System > Software, install luci-app-commands System > Custom Commands Configure > Add Name: Delete profiles Command: rm /etc/bosminer-autotune.json Dashboard > Run Delete profiles Quick Actions, start bosminer
Of course you could instead just ssh into the miner and do the same: ssh root@IP_ADDRESS '/etc/init.d/bosminer stop && rm /etc/bosminer-autotune.json && /etc/init.d/bosminer start'
Or do it in batch using the bos-toolbox: bos-toolbox command iplist.txt "/etc/init.d/bosminer stop && rm /etc/bosminer-autotune.json && /etc/init.d/bosminer start"
Isn't it great to have a proper OS running in your miner, rather than that Xilinx crud everyone else just modifies because they are too lazy to do any better?
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
philipma1957
Legendary
Offline
Activity: 4102
Merit: 7765
'The right to privacy matters'
|
|
April 03, 2021, 11:59:52 AM |
|
braiins has shown to work better for the 10 s9's and the one testing s17. That I loaded braiins to.
eventually I will place more gear on braiins.
I have been neglecting sha 256 asic gear and mining due to the gpu/eth boom.
I can still get an occasional gpu close to msrp. Mine eth and swap to cash /BTC
I Just did that this morning converted 600 in eth to 300 in btc and 300 in cash
So my attention is grabbed by gpus more than asics. Due to superior profits available to gpu miners.
I like braiins and eventually will likely end up with most of my asic gear using it.
|
|
|
|
Bitcguru77
Jr. Member
Offline
Activity: 48
Merit: 14
|
|
April 03, 2021, 01:32:57 PM |
|
To delete the profiles just do the following from the miner's UI:
Quick Actions, stop bosminer System > Software, install luci-app-commands System > Custom Commands Configure > Add Name: Delete profiles Command: rm /etc/bosminer-autotune.json Dashboard > Run Delete profiles Quick Actions, start bosminer
Of course you could instead just ssh into the miner and do the same: ssh root@IP_ADDRESS '/etc/init.d/bosminer stop && rm /etc/bosminer-autotune.json && /etc/init.d/bosminer start'
Or do it in batch using the bos-toolbox: bos-toolbox command iplist.txt "/etc/init.d/bosminer stop && rm /etc/bosminer-autotune.json && /etc/init.d/bosminer start"
Isn't it great to have a proper OS running in your miner, rather than that Xilinx crud everyone else just modifies because they are too lazy to do any better?
Hi Artemis. Thanks a lot for this info. I'll try it out when it gets a little warmer outside. BR. Steff
|
|
|
|
MiniMike
Jr. Member
Offline
Activity: 71
Merit: 5
|
|
April 13, 2021, 08:58:38 PM |
|
Hello,
A small question regarding the maximum power of 1600W for an APW3++ power supply for an S9i. I have one of my S9i that has a card out of order, so I unplugged it. If I leave the Braiins OS+ configuration on 1600W, will I have a maximum of 800W in each card or the software will automatically calculate to put only 533W per card?
Thanks Mickael
|
|
|
|
jameslg383
Newbie
Offline
Activity: 1
Merit: 0
|
|
April 20, 2021, 12:37:18 PM |
|
anyone else have trouble with brains and Awesome miner?
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
April 20, 2021, 07:41:05 PM |
|
Hello,
A small question regarding the maximum power of 1600W for an APW3++ power supply for an S9i. I have one of my S9i that has a card out of order, so I unplugged it. If I leave the Braiins OS+ configuration on 1600W, will I have a maximum of 800W in each card or the software will automatically calculate to put only 533W per card?
Thanks Mickael
If you read Bitmain's documentation, you will notice they say efficiency is good up to 93.5% load, then it drops very fast. This means 1496W should be the theoretical MAX value. Switching PSUs should not be run at full capacity for sustained periods of time. Safety margin is in order. Commonly with computers or electricity in general, people leave 20% margin, which for 1600W means 1280W. In electricity (and electronics) you don't want to be running things at their max ratings, always leave a safety margin. For this reason the default comes at 1420W which is meant for the APW3++ that many S9s use. Also, it is a known fact that Bitmain asics are more efficient a slower speeds, which is why many people use values near 900W for the power limit value, which also allows it to run at 110V and a single fan. To answer your question, the answer is no. Each hashboard will always get 1/3rd (or slightly less) of the specified power limit value, so you don't need to be changing this value if you have less boards enabled or connected.
And now an announcement: Braiins OS+ Nightly Release for X17 DevicesWhat's new: + the tuner has been significantly improved to ensure faster convergence and more stable tuning configurations. Old tuner profiles are kept, but ignored. + for safety reasons, the fans are running @ 100 % during the tuning phase. Once finished, the user settings are used + BOSminer will keep on restarting underperforming hash boards instead of switching them off completely. The delay between restarts exponentially grows from 5, 10, 20, etc., up to 180 minutes if the hash board performance doesn't improve. (In some cases, a simple restart is all that's needed for the underperforming boards to begin hashing properly.) +Dynamic Power Scaling now works even with Manual Fan Control How to install the nightly build:1. Download the new BOS Toolbox from here: Windows - https://feeds.braiins-os.com/toolbox/latest/bos-toolbox.zipLinux - https://feeds.braiins-os.com/toolbox/latest/bos-toolbox2. Install/Update Braiins OS+ with the following command: Windows - bos-toolbox.bat install --nightly list.csv Linux - ./bos-toolbox install --nightly list.csv Documentation for more detailed instructions on how to update: https://docs.braiins.com/os/plus-en/Setup/1_quickstart.html#update-braiins-os
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
gt_addict
|
|
May 26, 2021, 09:28:16 PM |
|
Whats the latest release for the S9?
My current firmware is dated 27/11/2020.
Auto Update is ticked and I've tried "bos-toolbox update" but any method I try says that its the latest firmware, but I've seen listings of S9s on ebay with a different GUI which I'd like.
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
May 31, 2021, 01:16:08 PM Last edit: May 31, 2021, 01:33:56 PM by Artemis3 |
|
For S9 the current latest "major" is 2020-11-27 and latest "minor" is 2021-04-29 which for most users is just a small UI update. It does add support to the Braiins OS Manager if you want to test it. The Minor releases need to be upgraded or installed manually rather than with the usual built in upgrade methods.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
gt_addict
|
|
May 31, 2021, 05:36:15 PM |
|
So thats a case of switching the jumper and loading to an sd card and writing to nand again?
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
May 31, 2021, 06:48:31 PM |
|
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
gt_addict
|
|
May 31, 2021, 07:05:51 PM Last edit: May 31, 2021, 07:20:04 PM by gt_addict |
|
Thanks Artemis, I tried that but obviously the wrong file lol. I didn't realise it was the one for the arm controller.
EDIT:-
Just flashed it. Works perfectly. Thanks again.
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
philipma1957
Legendary
Offline
Activity: 4102
Merit: 7765
'The right to privacy matters'
|
|
June 11, 2021, 05:41:00 PM |
|
any one running s17s I have a s17 running and used tuner vs my settings
I am trying to determine how long tuner tunes.
also what are people getting with the tuner set to 1425 watts
I am at 1 hour and 11 minutes and around 42 th at 1425 watts setting
I have this firmware
2020-12-17-0-27e4d572-20.12-plus
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2016
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
June 13, 2021, 03:54:47 PM |
|
any one running s17s I have a s17 running and used tuner vs my settings
I am trying to determine how long tuner tunes.
also what are people getting with the tuner set to 1425 watts
I am at 1 hour and 11 minutes and around 42 th at 1425 watts setting
I have this firmware
2020-12-17-0-27e4d572-20.12-plus
You are running a version too old, the x17 family has gotten many updates and bug fixes, in the following days should come another release, but you can try enabling nightly feeds (only if installed into NAND, SD image here) in the meantime. The latest nightly is 2021-06-10.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
|