Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner

[astraleureka]

Dead of half miner chain 3 of Dayun Z1
WTF Dayun

https://i.imgur.com/RC6r7Lr.png

The word 'chain' is literal, if ASIC 20 is completely failed the ASICs following it will not respond either.

Unstable. Look up other ASIC alternatives. Like Inno A9 zmaster or Antminer Z9.

It's not the same algorithm.

[1715419321]

1715419321

[1715419321]

1715419321

[1715419321]

1715419321

[zigminer]

Dead of half miner chain 3 of Dayun Z1
WTF Dayun

https://i.imgur.com/RC6r7Lr.png

i think you need set freq to 800mhz and try mining

[zigminer]

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

[astraleureka]

Disabling SSH will not prevent vendors from doing this... they can just modify the firmware on the USB key. There is no effective method to prevent this, really...

[Yezzzuurrr]

Profitability again lower from everyone? I got 0.00235 today

[minefarmbuy]

Big market dip right now.

[mine_phun]

Hello everyone,

Spamming is not my thing, so i'll try to keep it short

@Nlpool.nl  we are running a profitswitching pool also running the Lyra2V2 algo and the most profitable Lyra2V2 coins in it, meaning you can set a BTC or LTC wallet , but also any other coin wallet as long as the coin is present in our pool.

As the pool can use some extra hashrate to make it even more efficiënt i am looking for people with the Z1 miners.

If you can help me out and if you are looking for some extra profit : > i can give you a 5% extra weekly bonus if you are a big miner for 4 weeks. If you are interested please contact me @ Discord or Telegram.

>>

NLPOOL.NL | Highly profitable Lyra2V2 Mining Pool


Start Mining:

Code:

-o stratum+tcp://mine.nlpool.nl:4533 -u <Your BTC WALLET_ADDRESS> -p c=x

Our features:

- Approximately 20 - 30% extra profits with custom finetuned profit switching system in the pool
- Payouts possible in any currency present in our pool (LTC / BTC / RACE / VTC etc.)
- High profits for miners by lowering latency and stale shares
- Blocks are distributed proportionally among valid submitted shares.
- High security / DDOS protection with 99% uptime, multiple nodes, loadbalancers and status system
- Professional pool - No un-announced downtime. We care for your profits.
- Hourly payments
- 0.25% fee

Support
Telegram - Telegram
Discord - Discord

[mininghosting.eu]

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

[Phuripat]

We have now discontinued z1 and z1+.
ensure mining difficult not grow.
2018/11/16 will release new firmware , add fan check option.

we want a stable firmware and can run at full speed as describe 6.8 or 7.2 GH

[lennujuht]

Ive img firware 1105, but it doesn't work at all and I do not see bin folder in USB. Can u help?

[zigminer]

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

After the firmware is modified, the frequency can be set to 1000mhz, many user hash boards are burned. For such users, how do we carry out after-sales maintenance?
check this image , freq max 1000mhz
https://imgur.com/a/1x7dr79

[revenant2017]

Dead of half miner chain 3 of Dayun Z1
WTF Dayun

https://i.imgur.com/RC6r7Lr.png

The word 'chain' is literal, if ASIC 20 is completely failed the ASICs following it will not respond either.

Unstable. Look up other ASIC alternatives. Like Inno A9 zmaster or Antminer Z9.

It's not the same algorithm.

It's still ASIC. They both function the same. They both generate money and consume electricity. The problem is, it's efficiency.

[Yezzzuurrr]

Does a higher freq really gives you a better result anyway?
Are you gonna make a place where we can buy spare parts for this miner when things go wrong?

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

After the firmware is modified, the frequency can be set to 1000mhz, many user hash boards are burned. For such users, how do we carry out after-sales maintenance?
check this image , freq max 1000mhz
https://imgur.com/a/1x7dr79

[OmerSari]

You are talking about the fact that I can increase the clock speed to 1000. That's right, but if you see it, it's at 950  

So we can overclock him up to 1000 but we didn't do it.

Ori, As you check all the machines from my laptop and took the screenshots you didn't saw any machine was overclocked to 1000  

Beyond that you have it yourself on the google drive an image of 900_stable.
https://drive.google.com/drive/folders/1Z5vPZfQCwFsvYJwzzQ2kK_GUIMCA-YxS
Before you talk to me make sure you remove the overclock_900. Of those 50, I did not see Z1 get broken by overclock to 950!
https://imgur.com/a/qkyDzDk

Apart from that, Me and my colleagues have taken all care of what you all have not done: deliver a good software to a Dayun!

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

After the firmware is modified, the frequency can be set to 1000mhz, many user hash boards are burned. For such users, how do we carry out after-sales maintenance?
check this image , freq max 1000mhz
https://imgur.com/a/1x7dr79

[iwouldifiwereyou]

Should I buy Z?

Helll no, i hate it. Dropped from 50 a day to 18 the day I bought it. But I hate using it too, tweaking it and updating firmware has been a joke, then this locking out of SSH with later firmware.

[Mordred80]

New firmware is out for Z1/Z1+, Version 20181116

https://drive.google.com/drive/folders/1jklZzNDkBKDxHUQKd5V9kKiu_QWlcUug

Now i really hope that this option was added so that i can resume mining.

2018/11/16 will release new firmware , add fan check option.

[zigminer]

You are talking about the fact that I can increase the clock speed to 1000. That's right, but if you see it, it's at 950  

So we can overclock him up to 1000 but we didn't do it.

Ori, As you check all the machines from my laptop and took the screenshots you didn't saw any machine was overclocked to 1000  

Beyond that you have it yourself on the google drive an image of 900_stable.
https://drive.google.com/drive/folders/1Z5vPZfQCwFsvYJwzzQ2kK_GUIMCA-YxS
Before you talk to me make sure you remove the overclock_900. Of those 50, I did not see Z1 get broken by overclock to 950!
https://imgur.com/a/qkyDzDk

Apart from that, Me and my colleagues have taken all care of what you all have not done: deliver a good software to a Dayun!

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

After the firmware is modified, the frequency can be set to 1000mhz, many user hash boards are burned. For such users, how do we carry out after-sales maintenance?
check this image , freq max 1000mhz
https://imgur.com/a/1x7dr79

We are not dayun！
The stable frequency of z1 is 900Mhz
The stable frequency of z1+ is 925Mhz

[metnet]

Dear Zigminer,

You posted screenshots you secretly took during a teamviewer session.

Let me explain why we made modifications to you firmware.
We are a hosting company, hosting a lot of ASIC-Miners.

In order to host more than 1 Miner, we need the miners to have different IP addresses.
This already is the first shortcoming of the Zigminer Firmware.

Every miner will use the same static IP chosen by you. Even after changing it in the webinterface of the miner to DHCP it keeps the same IP.
That is why we began to modify the firmware, so that we can actually use the miners.
We hardcoded the firmware to DHCP.

Then we realized that the method you use to set up a MAC adress was also messy and didnt work well. There even is a firmware version you provide with fixed MAC address. Not very handy.


In the screenshot you provided you can see that our company name was added to the webinterface (https://www.mininghosting.eu). That doesn't change functionaltiy. But it was a good indicator for us and for our clients that the miner is running a repaired version of your firmware.
To disable SSH and therefore remove important monitoring options again makes the zigminer less and less attractive to use.
Compared to other ASICs the Z1 is very unstable, therefore monitoring is key.

I hope you will enable SSH again, so we can use the newest firmware you provide.

@zigminer,

I have 40 zig z1 miners.

In some cases I have the problem that I can reach them but when I log in via ssh I can see via command "top" that the miner the process FPGA_Download is active. When this process is activated, the miner can not start mining.
I searched a lot on the internet for this problem but could not find anything about it that you could find it.

Yesterday I tried the new firmware 1105, this firmware is indeed a bit faster but the layout is the same. Is OK. What I also find very sorry about this version is that they have shielded the SSH and have also created an encrypted partition in the image.

Why is SSH so important to me:
I can then manage and control all miners in my software, like reboot and read out the values, such as hashrate. Because they have a lot of problems with.

The built-in function of the miner does not always work well. That is why I made a script and applied it in the previous Firmware versions so that if the miner stays below the average hashrate within 60 minutes, the miner must restart.

I cannot do that now with the new Firmware 1105. I would like more information about this so I also have access to SSH at Firmware 1105.

I closed the SSH because some vendors had changed their procedures privately, causing mine operations to be unstable.

https://imgur.com/a/Lo7McuV
https://imgur.com/a/1x7dr79
https://imgur.com/a/wNUfjv2

After the firmware is modified, the frequency can be set to 1000mhz, many user hash boards are burned. For such users, how do we carry out after-sales maintenance?
check this image , freq max 1000mhz
https://imgur.com/a/1x7dr79

you are right. thanks for new image. i want to check it, but it does not open.

[metnet]

New firmware is out for Z1/Z1+, Version 20181116

https://drive.google.com/drive/folders/1jklZzNDkBKDxHUQKd5V9kKiu_QWlcUug

Now i really hope that this option was added so that i can resume mining.

2018/11/16 will release new firmware , add fan check option.

did you try Mordred80. does it work?

[Mordred80]

New firmware is out for Z1/Z1+, Version 20181116

https://drive.google.com/drive/folders/1jklZzNDkBKDxHUQKd5V9kKiu_QWlcUug

Now i really hope that this option was added so that i can resume mining.

2018/11/16 will release new firmware , add fan check option.

did you try Mordred80. does it work?

I did not try it yet cos i'm at work.
Have to wait ~8h till i'm home again.
Then i'll try.