terra.tec
Newbie
Offline
Activity: 9
Merit: 1
|
|
October 01, 2021, 06:54:07 AM |
|
Hey what can I do, when a hashboard ramps up sending shares (only ~700 Gh at ~60 Watts) and seconds later stays at 0 hashes? With "screen -r" I can see: Pool in-service, we can send shares!
Found boards: 1 Broken SPI: 1
EVENT: 2021-09-30 12:47:34 ::: PWC_RESTART ::: brd=0, pwc=0/0 EVENT: 2021-09-30 12:47:35 ::: PWC_RESTART ::: brd=0, pwc=0/2
Can provide full logs if you need more details. Thank you
|
|
|
|
mario312
Newbie
Offline
Activity: 4
Merit: 0
|
|
October 01, 2021, 01:47:45 PM |
|
Things done: Orange Pi 4 (Apollo's controller) 7mm fan increased to full 5V, it was overheating before
Did you replace it with the Pi 4? Because mine appears to have a Pi 3.
|
|
|
|
jstefanop (OP)
Legendary
Offline
Activity: 2137
Merit: 1398
|
|
October 01, 2021, 05:00:20 PM |
|
Hey what can I do, when a hashboard ramps up sending shares (only ~700 Gh at ~60 Watts) and seconds later stays at 0 hashes? With "screen -r" I can see: Pool in-service, we can send shares!
Found boards: 1 Broken SPI: 1
EVENT: 2021-09-30 12:47:34 ::: PWC_RESTART ::: brd=0, pwc=0/0 EVENT: 2021-09-30 12:47:35 ::: PWC_RESTART ::: brd=0, pwc=0/2
Can provide full logs if you need more details. Thank you Reply to your order email with the full log, and well check whats up.
|
|
|
|
slurfius
Jr. Member
Offline
Activity: 104
Merit: 7
|
|
October 01, 2021, 05:46:33 PM |
|
I seen a standard unit on eBay with a broken usb c port what would it take to get that repaired?
|
|
|
|
cryptofreshman
Newbie
Offline
Activity: 13
Merit: 0
|
|
October 01, 2021, 06:31:39 PM |
|
Currently have mine on slushpool. After I have enough to receive a payout can anyone recommend a solid P2Pool with a lower hashrate that is finding blocks?
|
|
|
|
MLOMBANA
Newbie
Offline
Activity: 5
Merit: 0
|
|
October 01, 2021, 07:15:32 PM |
|
I'm not sure if I'm the only one that is experiencing this but searching this thread is a nightmare, I'm finding that every few days my standard hashboard unit will fade off leaving only my main controller unit working. Obviously, this takes my hashrate from 4.5 to 2.0'ish but for no apparent reason.
My 2 boxes are in an air conditioned environment, I've run Bitmain ASIC's in that same room with no issue and they are on a UPS for power consistency.
The fix is simple, reboot the boxes and I'm up and running but now I'm finding that I'm having to play babysitter.
Is this something that anyone else is experiencing?
Thanks! ML
|
|
|
|
gigahashes
Newbie
Offline
Activity: 16
Merit: 0
|
|
October 01, 2021, 07:54:44 PM Last edit: October 01, 2021, 09:20:37 PM by gigahashes |
|
Hi, been mining away happily for nearly a week, now seeing : There is a problem fetching system stats (Internal error) tried restart, message still the same.
2.47 Th/s Current hashrate 15 Min Avg: 2.47 Th/s 158 Watt Miner power usage Watts per TH/s: 64 0.4% Hardware errors Rejected: 3 2 hours Miner uptime Last share: a few seconds ago Hashboards Status ID Hashrate Temp Fan Speed Power Voltage Error Active ASICs Active HASHBOARD #0 2.47 Th/s 60°c 1738 rpm 158 W 8.09 v 0.4% 44
Any clues please?
Thanks in advance :-)
Also 2.03 Th/s 0.00°C
|
|
|
|
jstefanop (OP)
Legendary
Offline
Activity: 2137
Merit: 1398
|
|
October 01, 2021, 10:53:22 PM |
|
I'm not sure if I'm the only one that is experiencing this but searching this thread is a nightmare, I'm finding that every few days my standard hashboard unit will fade off leaving only my main controller unit working. Obviously, this takes my hashrate from 4.5 to 2.0'ish but for no apparent reason.
My 2 boxes are in an air conditioned environment, I've run Bitmain ASIC's in that same room with no issue and they are on a UPS for power consistency.
The fix is simple, reboot the boxes and I'm up and running but now I'm finding that I'm having to play babysitter.
Is this something that anyone else is experiencing?
Thanks! ML
This is a known issue that will be fixed next update. Its caused by an unstable internet connection, so you can improve this if your on wifi, but if your ISP is causing it there is not much you can do until we issue the fix.
|
|
|
|
crypto_curious
|
|
October 02, 2021, 05:43:14 AM |
|
~ snip ~
Interesting, you're the first one I come across that reinstalled the OS from scratch on an Apollo. I'm wondering then, how you got the miner working? I understood that we're not supposed to do anything with the system, not even package upgrades, since it could break something in the driver for the hashboard or something like that. Yes, that's right, if you do Ubuntu updates, it may break mining. Jstefanop use third party software package to enable miner communication via GPIO pins on top of the Orange Pi. There is some incompatibility in this software if you update system by hand. I worked around that by connecting miner via USB cable to itself. Every shipped miner can work either via GPIO or USB.
|
|
|
|
crypto_curious
|
|
October 02, 2021, 05:51:49 AM |
|
Things done: Orange Pi 4 (Apollo's controller) 7mm fan increased to full 5V, it was overheating before
Did you replace it with the Pi 4? Because mine appears to have a Pi 3. No, my full package Apollo came with Orange Pi 4, 6-core, 4GB RAM. $ inxi -F System: Host: orangepi4 Kernel: 5.10.63-rockchip64 aarch64 bits: 64 Console: tty 3 Distro: Armbian GNU/Linux 11 (bullseye) Machine: Type: ARM Device System: OrangePi 4 details: N/A serial: CPU: Info: 6-Core (2-Die) model: N/A variant-1: cortex-a53 variant-2: cortex-a72 bits: 64 type: MCP MCM Speed: 1800 MHz min/max: 408/1416:1800 MHz Core speeds (MHz): 1: 1416 2: 1416 3: 1416 4: 1416 5: 1800 6: 1800
|
|
|
|
n0nce
|
|
October 02, 2021, 02:41:48 PM |
|
~ snip ~
Interesting, you're the first one I come across that reinstalled the OS from scratch on an Apollo. I'm wondering then, how you got the miner working? I understood that we're not supposed to do anything with the system, not even package upgrades, since it could break something in the driver for the hashboard or something like that. Yes, that's right, if you do Ubuntu updates, it may break mining. Jstefanop use third party software package to enable miner communication via GPIO pins on top of the Orange Pi. There is some incompatibility in this software if you update system by hand. I worked around that by connecting miner via USB cable to itself. Every shipped miner can work either via GPIO or USB. Oh yes, this makes so much sense! After all, the standard unit is basically an Orange Pi and a 'Only Hashboard' in one single case. I think I would then also just omit the GPIO connector and add a small USB cable; that way I can run my own OS @jstefanop is there any reason (except maybe the sleekness of the device) to use the GPIOs? Maybe better hashrate? For keeping the device's sleek design, but allowing users to run own OS, it might be cool to offer the GPIO connection software as a package to install!
|
|
|
|
poonasor
Jr. Member
Offline
Activity: 49
Merit: 5
|
|
October 03, 2021, 08:12:39 PM |
|
GPU miner here, been running dual PSUs for last decade. My typical rig consists of one motherboard, 6 or 8 cards, two PSUs 650-850W each, for total of 1100-1200W per rig. They are running for years on end, without any reboots. I presume you just speaking from what you heard, not real experience? I agree, that running two PSUs on one electrical device (like one Apollo or one GPU) is a no no. But don't extrapolate that to "One should NEVER try to run ANY sort of PSU's in parallel" (your quote), because that's BS.
Are you running your PSUs in parallel or in series though? It seems you have one set of things powered by one and another set of things powering separate items. The current only flows through one path in a series setup. Exactly, I Previously had 2 gpu-mining rigs, one running 12 cards the other with 5 cards. Having 2 power supplies is fine as long as you have it set up correctly. First you’ll need a piece of hardware like add2psu which connects the 2nd-slave psu to the master, you can also use a paper clip if you’re willing to take that risk. The main thing is to connect the peripherals to 1 psu and not both. For example for mining rigs the gpu riser and gpu will be connected to 1 psu so both pull from the same power source. You should never connect the riser to one and the gpu on it to another, that would cause problems. So I’m terms of the Apollo don’t plug 2 separate power suppliers into 1 machine.. My old rig ran 24/7 for around 3 years straight never had any serious problems or fire related incidents, you just need to know what you’re doing
|
|
|
|
poonasor
Jr. Member
Offline
Activity: 49
Merit: 5
|
|
October 03, 2021, 08:31:42 PM |
|
I’ve tried to search through the threads and did a search and really didn’t find anything but has anyone tried to add sha256 usb miners to the Apollo?
It probably isn’t worth it in terms of extra electricity usage but I have 2 Ttbit sha256 usb miners lying around and is wondering if I can hook it up to the Apollo rig.
Has anyone tried something like that?
|
|
|
|
02EX
Newbie
Offline
Activity: 14
Merit: 2
|
|
October 04, 2021, 12:16:11 AM |
|
FYI After having units running from Batch 1 and units from batch 2 I have found a difference in temps and fans speeds from the two batches. Although I was concerned I'm not to concerned now, just for fan longevity of batch 1 fans. It all started when I added a batch one unit to my batch 2 setup Batch 1 Setup https://imgur.com/a/A0KMm1H Batch 2 Setup not as fancy, https://ibb.co/s9S5NVcAll batch 2 unit temps were 68c-69c and fan speeds 2800-2900rpm constant across the 7 units from batch 2 When I added a batch 1 unit to the other 7 units one unit was 62c-63c and fan speed 3000-3100rpm (so lower temp with faster rpm) The question to myself was why is one unit so far apart from the others (originally didnt know it was the batch 1 unit yet) Through process of trouble shooting I isolated the lower temp unit and swapped the fan for one of the others of the consistent temps and fan speed like the others. I found out that it was not the unit but the fan itself as the lower temp and faster rpm followed the fan from unit to unit. I further looked at the fans closer and notice a distinctive difference. Batch 1 (4 units) I got had these fans with smaller gauge wires and a different wiring pattern. Blue yellow red black https://ibb.co/GTGwJkHBatch 2 units had larger gauge wires Black red yellow blue https://ibb.co/NZkKXWBBoth fans do have the same order at the plug to the board just different going into the fan. (different brand of fan I take it) In conclusion the difference between the fans from Batches is quite noticeable so if your seeing this too, here is what I found.
|
|
|
|
jstefanop (OP)
Legendary
Offline
Activity: 2137
Merit: 1398
|
|
October 04, 2021, 03:07:57 PM |
|
FYI After having units running from Batch 1 and units from batch 2 I have found a difference in temps and fans speeds from the two batches. Although I was concerned I'm not to concerned now, just for fan longevity of batch 1 fans. It all started when I added a batch one unit to my batch 2 setup Batch 1 Setup https://imgur.com/a/A0KMm1H Batch 2 Setup not as fancy, https://ibb.co/s9S5NVcAll batch 2 unit temps were 68c-69c and fan speeds 2800-2900rpm constant across the 7 units from batch 2 When I added a batch 1 unit to the other 7 units one unit was 62c-63c and fan speed 3000-3100rpm (so lower temp with faster rpm) The question to myself was why is one unit so far apart from the others (originally didnt know it was the batch 1 unit yet) Through process of trouble shooting I isolated the lower temp unit and swapped the fan for one of the others of the consistent temps and fan speed like the others. I found out that it was not the unit but the fan itself as the lower temp and faster rpm followed the fan from unit to unit. I further looked at the fans closer and notice a distinctive difference. Batch 1 (4 units) I got had these fans with smaller gauge wires and a different wiring pattern. Blue yellow red black https://ibb.co/GTGwJkHBatch 2 units had larger gauge wires Black red yellow blue https://ibb.co/NZkKXWBBoth fans do have the same order at the plug to the board just different going into the fan. (different brand of fan I take it) In conclusion the difference between the fans from Batches is quite noticeable so if your seeing this too, here is what I found. There are a few differences between batches and even units within batches. We have multiple van vendors and their PWM curves are not exact match, so some fans will be faster.
|
|
|
|
crypto_curious
|
|
October 04, 2021, 05:10:02 PM |
|
@jstefanop is there any reason (except maybe the sleekness of the device) to use the GPIOs? Maybe better hashrate? For keeping the device's sleek design, but allowing users to run own OS, it might be cool to offer the GPIO connection software as a package to install! I don't know for sure, but this must be for aesthetics only. Everything fits under miner skirt. No extra USB cable required. Hashrate is the same in both cases, I've tried that, no differences in performance. Functionality also seems to same, hashrate readings, speed, fans, temps, power use. So feel free to give your Full unit a USB cable so you can install system of your choice. You can always revert to Futurebit system if you don't like it, by reformatting SD card and removing USB cable.
|
|
|
|
gt_addict
|
|
October 04, 2021, 08:56:47 PM |
|
Is there any way to get the CPU fan to run at a faster speed?
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
terra.tec
Newbie
Offline
Activity: 9
Merit: 1
|
|
October 04, 2021, 09:02:03 PM |
|
@jstefanop is there any reason (except maybe the sleekness of the device) to use the GPIOs? Maybe better hashrate? For keeping the device's sleek design, but allowing users to run own OS, it might be cool to offer the GPIO connection software as a package to install! I don't know for sure, but this must be for aesthetics only. Everything fits under miner skirt. No extra USB cable required. Hashrate is the same in both cases, I've tried that, no differences in performance. Functionality also seems to same, hashrate readings, speed, fans, temps, power use. So feel free to give your Full unit a USB cable so you can install system of your choice. You can always revert to Futurebit system if you don't like it, by reformatting SD card and removing USB cable. Is it okay to have GPIO and USB connected at the same time and initialize only the preferred connection?
|
|
|
|
crypto_curious
|
|
October 04, 2021, 10:17:08 PM |
|
Is there any way to get the CPU fan to run at a faster speed?
Yes, I did that in mine, it's connected to deliberately lower 3.3V, I put it back to 5V. You can do that by re-crimping the wire or just forcing it through the hole with 5V. You can find 5V by checking Orange Pi 4 pinout or checking with multimeter, as you will already know where GND is, just find where 5V is. 5V it's right next to 3.3V, but check exactly if front or rear row somewhere.
|
|
|
|
gt_addict
|
|
October 05, 2021, 08:06:17 AM Last edit: October 05, 2021, 04:20:11 PM by gt_addict |
|
Is there any way to get the CPU fan to run at a faster speed?
Yes, I did that in mine, it's connected to deliberately lower 3.3V, I put it back to 5V. You can do that by re-crimping the wire or just forcing it through the hole with 5V. You can find 5V by checking Orange Pi 4 pinout or checking with multimeter, as you will already know where GND is, just find where 5V is. 5V it's right next to 3.3V, but check exactly if front or rear row somewhere. Thats what I thought. I’ll make up a gpio to fan connector lead and plug it in at some point when I get time. EDIT:- Both 5v GPIO pins are used by the proprietary plug so couldn't get access to it without cutting wires which I'm not prepared to do so I'll just put up with it.
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
|