Ultra Under-overclock image for A2 Innosilicon by Emdje - V5.0

[emdje]

You might use an older version of the image, that might work better.

Image is not maintained anymore though due to lack of time and because my miner broke down 

[1715288114]

1715288114

[1715288114]

1715288114

[Tylerstewart86]

So iv tried to create a new sd card and it is not showing up on my pi would anyone be able to make a working image and sell it

[Bandorlol]

Hi
Know this is an old thread, but the extranounce feature would be very good to have. Is there any chance of getting this firmware/driver running on the 12chip version of A2? (blue card)
I can provide logs if necessary, error is not any A1 / A2 boards found. Someone suggested this could be related to the reset-command not working?

i tried all version, in this thread but all gives error Not any A2 board found, also tried the A2mini image - gave error Not any A1 boards found.

ANX-edition is working, but as I understand that is with stock cgminer version...

-stado

[archip]

Note that the default frontend is set-up for 6 chip blades, meaning that the MH/s values and so on. I will upload other versions of the frontend later that you can manually replace.

Hi!
If there any firmware image for 5 chip blades?
I tried v4 and v5 image, but my A2 110mh with 5 chip blades does not working correctly.

[emdje]

Note that the default frontend is set-up for 6 chip blades, meaning that the MH/s values and so on. I will upload other versions of the frontend later that you can manually replace.

Hi!
If there any firmware image for 5 chip blades?
I tried v4 and v5 image, but my A2 110mh with 5 chip blades does not working correctly.

No I do not have a version for a 5 chip blade.
Innosilicon never designed such a version.

Good luck with the search for a working version.

[KingWilly]

do you think your A2-firmware would run on an A4 ?!
I'll give it a try, if i can find your cgminer version. (no need for a complete image)

it has 20 chips per blade (20*4=80 chips total)

Cheers..

[emdje]

do you think your A2-firmware would run on an A4 ?!
I'll give it a try, if i can find your cgminer version. (no need for a complete image)

it has 20 chips per blade (20*4=80 chips total)

Cheers..

It might.....
I have not seen the software, but I assume they have used the same source.
They used the source of the A1 for the A2 as well, and judging from the interface it looks pretty similar.
But I don't know if the hardware side is the same and all the dependencies are the same.
Would love to know if it did.

[KingWilly]

do you think your A2-firmware would run on an A4 ?!
I'll give it a try, if i can find your cgminer version. (no need for a complete image)

it has 20 chips per blade (20*4=80 chips total)

Cheers..

It might.....
I have not seen the software, but I assume they have used the same source.
They used the source of the A1 for the A2 as well, and judging from the interface it looks pretty similar.
But I don't know if the hardware side is the same and all the dependencies are the same.
Would love to know if it did.

Ahh, bugger... tried it but chips count is wrong and it starts nagging about everything..
found the cgminer 3.9 dirty source for the A4/A2.. so i'll go play around there..
(https://github.com/Binary4/cgminer-3.9.0-a4-12-dg)

Did you use cgminer 4.1 for some parts ? (if so, which one).

Cheers..

[hanz0n]

i know this is an old thread,
but does any one have this img file for raspberry pi ?

the next question, any one know how or if its possibly to driect connect a v1.2 blade to a pie ? or any schematics for v.1.2 blade ?