pekatete
|
|
April 02, 2015, 01:36:02 AM |
|
@pekatete, dead fan, we do offer replacement. The fans used on Antminer is not an easy one to find as it uses 4 wires and high RPM. We are sorry for the inconvenience. Our USA based team can take care of you faster usually and they are available 24/7. Thank you for the stats!!
52 is a bit warm but it is well in the range.
Not sure you are thanking me, but I'll accept anyway; You are welcome. The 52 refered to is the top temp, i.e with that configuration, the temps never go above 52 during the day (and currently below 48 at night). I actually believed 52 was a brilliant top temp, but I've not had a different temp to compare with as my S5 shipped with a stone dead fan that never turned a fin in anger! I was advised to buy one from the local market (without any hint of irony or any offer for a replacement .... not even a voucher offer!). Better late than never .... but I am not based in the US, rather the UK, so it may be tricky for me to send you the dead fan (which I still have and looks pristine next to the others I salvaged from my now decomisioned S1's!). If on the other hand you can send me the replacement without me having to meet the cost of mailing you the dead one, I'll be more than happy to furnish any info you require.
|
|
|
|
|
|
|
|
|
The Bitcoin network protocol was designed to be extremely flexible. It can be used to create timed transactions, escrow transactions, multi-signature transactions, etc. The current features of the client only hint at what will be possible in the future.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
|
April 02, 2015, 01:53:03 AM |
|
@Pekatete, if your purcahse was within the last 90-days, please e-mail support@bitmain.zendesk.com and attach your Order Confirmation page in PDF with your shipping address information. There is a service center in Serbia that may be able to service you closer than USA. @pekatete, dead fan, we do offer replacement. The fans used on Antminer is not an easy one to find as it uses 4 wires and high RPM. We are sorry for the inconvenience. Our USA based team can take care of you faster usually and they are available 24/7. Thank you for the stats!!
52 is a bit warm but it is well in the range.
Not sure you are thanking me, but I'll accept anyway; You are welcome. The 52 refered to is the top temp, i.e with that configuration, the temps never go above 52 during the day (and currently below 48 at night). I actually believed 52 was a brilliant top temp, but I've not had a different temp to compare with as my S5 shipped with a stone dead fan that never turned a fin in anger! I was advised to buy one from the local market (without any hint of irony or any offer for a replacement .... not even a voucher offer!). Better late than never .... but I am not based in the US, rather the UK, so it may be tricky for me to send you the dead fan (which I still have and looks pristine next to the others I salvaged from my now decomisioned S1's!). If on the other hand you can send me the replacement without me having to meet the cost of mailing you the dead one, I'll be more than happy to furnish any info you require.
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA
|
|
|
pekatete
|
|
April 02, 2015, 02:00:19 AM |
|
@Pekatete, if your purcahse was within the last 90-days, please e-mail support@bitmain.zendesk.com and attach your Order Confirmation page in PDF with your shipping address information. There is a service center in Serbia that may be able to service you closer than USA. It is just inside 90 days, so I'll send an email to the above address and see what comes of it. Not sure what the wording should be in the email though (seeing it was info@bitmaintech.com who told me to get one from the local market) .... I'd like to get a replacement fan as the shipped one was a DOA .... would that suffice?
|
|
|
|
funtakus
Newbie
Offline
Activity: 36
Merit: 0
|
|
April 02, 2015, 12:35:52 PM |
|
|
|
|
|
notbatman
Legendary
Offline
Activity: 2212
Merit: 1038
|
|
April 02, 2015, 01:19:28 PM |
|
I've done some research, made some measurements and experimented with some 2-wire 120mm fans from old PSUs. I believe that two of the following fans will work in push/pull configuration to run at stock frequency (350M) or higher without going for gold in a banshee screeching contest. http://www.cougargaming.com/products/fans/vortex_pwm.html"Cougar Vortex" $11.89 USD each at the local shop.
|
|
|
|
valkir
Legendary
Offline
Activity: 1484
Merit: 1004
|
|
April 02, 2015, 01:38:13 PM |
|
I've done some research, made some measurements and experimented with some 2-wire 120mm fans from old PSUs. I believe that two of the following fans will work in push/pull configuration to run at stock frequency (350M) or higher without going for gold in a banshee screeching contest. http://www.cougargaming.com/products/fans/vortex_pwm.html"Cougar Vortex" $11.89 USD each at the local shop. Not enough CFM. These fans do max 70 cfm. ( I did try the same setup) You need more cfm. Check the delta fans.
|
██ Please support sidehack with his new miner project Send to :
1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
|
|
|
notbatman
Legendary
Offline
Activity: 2212
Merit: 1038
|
|
April 02, 2015, 01:57:29 PM |
|
I've done some research, made some measurements and experimented with some 2-wire 120mm fans from old PSUs. I believe that two of the following fans will work in push/pull configuration to run at stock frequency (350M) or higher without going for gold in a banshee screeching contest. http://www.cougargaming.com/products/fans/vortex_pwm.html"Cougar Vortex" $11.89 USD each at the local shop. Not enough CFM. These fans do max 70 cfm. ( I did try the same setup) You need more cfm. Check the delta fans. What's the minimum per fan CFM on a 2x fan setup? I'm able to run at a frequency of 250M hashing almost 800GH/s with two old PSU fans. These fans can't be more than 20 CFM each. This thing seems stable just below 50 deg.
|
|
|
|
scyth33
Member
Offline
Activity: 99
Merit: 10
|
|
April 02, 2015, 02:08:15 PM |
|
I see that you guys have the "newer" heatsink. I was given the heatsink similar to the S3s.
|
|
|
|
Darthswan
|
|
April 02, 2015, 02:15:39 PM |
|
With the open style of the s5, can you have a push/push or pull/pull setup? Or would that be to much? I ended up ordering another Delta fan off of Ebay $20. I unplugged the stock fan, and the temps went up to 58/63. Still not bad, but I like to be under 60. This is at stock setting, also.
|
|
|
|
hazenyc
|
|
April 02, 2015, 03:43:15 PM |
|
Would a Silverstone 1500W Power Supply be a good option to run 2x S5's?
|
|
|
|
Xian01
Legendary
Offline
Activity: 1652
Merit: 1067
Christian Antkow
|
|
April 02, 2015, 03:56:48 PM |
|
Interesting. Batch Five is now sold out.
|
|
|
|
sashapatrick
Newbie
Offline
Activity: 5
Merit: 0
|
|
April 02, 2015, 04:54:16 PM |
|
Received 3 miners. 2 blades are broken... Ask for replacement, but all goes too slow!!! One of two blades have burned chip place...
I am doing LEGO 2 days in a row and its very bad for my nervous system.
BITMAIN, PLEASE SEND ME REPLACEMENT LIKE YOU DID WITH FAN, 4 DAYS AND I RECEIVED IT....
please
|
|
|
|
larry12
|
|
April 02, 2015, 04:57:41 PM |
|
Hi guys, i'm looking to buy 3 x Antminer S5 from EU seller. If you have Ant's for sale please PM me.
Have a nice day.
|
#Bitcoin The future is here.
|
|
|
valkir
Legendary
Offline
Activity: 1484
Merit: 1004
|
|
April 02, 2015, 05:17:08 PM |
|
What's the minimum per fan CFM on a 2x fan setup?
I'm able to run at a frequency of 250M hashing almost 800GH/s with two old PSU fans. These fans can't be more than 20 CFM each. This thing seems stable just below 50 deg.
If you want to run it at default freq (350) you need minimum 200 cfm in my opinion. Something like 2 120 cfm fan using a push pull setup should work. Be sure to be below 60 on each blade.
|
██ Please support sidehack with his new miner project Send to :
1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
|
|
|
Biodom
Legendary
Offline
Activity: 3752
Merit: 3864
|
|
April 02, 2015, 05:23:20 PM |
|
What's the minimum per fan CFM on a 2x fan setup?
I'm able to run at a frequency of 250M hashing almost 800GH/s with two old PSU fans. These fans can't be more than 20 CFM each. This thing seems stable just below 50 deg.
If you want to run it at default freq (350) you need minimum 200 cfm in my opinion. Something like 2 120 cfm fan using a push pull setup should work. Be sure to be below 60 on each blade. I am running a 113 CFM fan (Delta AFB1212SH) in push at 350 with temp only 61/57 when ambient is at 30C. I am sure miner temp would be even lower at lower ambient. I might try push pull or leave it as is since I am very satisfied with much lower noise. See my detailed post a page or two above. BTW, it is a legend that you need to be below 60C, stably below 65 is fine-I run S5 like this (at 58-62C) for months before using Noctua. AFB1212SH is 40% of the Noctua price.
|
|
|
|
Biodom
Legendary
Offline
Activity: 3752
Merit: 3864
|
|
April 02, 2015, 05:31:33 PM |
|
Interesting. Batch Five is now sold out.
yep, they are probably massively producing it and hashing in their new hosting center. good for sellers in the aftermarket
|
|
|
|
Bitcoin Buyer Reload
|
|
April 02, 2015, 05:35:44 PM |
|
i would love to buy it but i have a feeling it will consume too much electricity from where i am. i have tried an online calculator. will breakeven in 3months or something, making maybe another version of the product to come out. i guess i will stay on this thread and once the next one is out, kindly let me know . i dont know if you have a customer list or something
|
|
|
|
Digitalmocking
|
|
April 02, 2015, 05:55:27 PM |
|
@BitMainWarranty, do you folks plan to offer more of the S5 before June 30th?
|
|
|
|
MyRig
Donator
Hero Member
Offline
Activity: 792
Merit: 510
support@myrig.com
|
|
April 02, 2015, 06:16:06 PM |
|
Once the batch 5 is sold out, batch 6 in June 9th is the only S5... Please wait for the official announcement for the next available miners. also, for the dead S5 or defective S5, turn around time via US/EU service center is as usual in just a few days. @BitMainWarranty, do you folks plan to offer more of the S5 before June 30th?
|
Antminer & DragonMint Repair E-mail: support@myrig.com T: @MyRig_com Return Address: MyRig 3700 Quebec Street, Unit 100-239, Denver, Colorado 80207, USA
|
|
|
Bitcoin Buyer Reload
|
|
April 02, 2015, 06:18:14 PM |
|
Once the batch 5 is sold out, batch 6 in June 9th is the only S5... Please wait for the official announcement for the next available miners. also, for the dead S5 or defective S5, turn around time via US/EU service center is as usual in just a few days. @BitMainWarranty, do you folks plan to offer more of the S5 before June 30th?
thank you very much. following. cheers
|
|
|
|
|