|
marvykkio
|
 |
April 20, 2015, 12:21:19 PM |
|
I had to buy 8 delta fans to see if I can lower the damn noise fan 8 x 4 antminer s5  |
|
|
|
|
|
|
|
There are several different types of Bitcoin clients. The most secure are full nodes like Bitcoin Core, but full nodes are more resource-heavy, and they must do a lengthy initial syncing process. As a result, lightweight clients with somewhat less security are commonly used.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
pekatete
|
|
April 20, 2015, 12:23:08 PM |
|
AFAIK there is no working solution to running S5 off SD card. There are instructions for recovery via SD but its not a full restore and will only work in some cases.
The recovery image has a reflash script in it that should fully re-image the emmc. It should work in all cases where the beaglebone hardware is undamaged. It would appear it first zeros out the emmc then copies the firmware files from itself. You can look at /etc/init.d/initc_emmc_flash.sh to see the rest of how this seems to be done. Last I remember you could keep running it off of the SD card after this process but I haven't checked in a while. It would actually be fairly easy to remove part of this script so it just keeps running off of the SD card and doesn't flash the emmc in case you didn't want to touch the internal memory. Hmm. When I tried it it didn't appear to do anything. Maybe my board was more than just a software brick. No, it's just your usual waffle. If you do not know something, don't comment rather than confuse users with your ignorance. Can someone that knows please tell me how to set voltage on an S5? I have tried setting it via the cgminer config file and restarting cgminer but the API still reports a voltage of 0725 |
|
|
|
smit1237
Full Member
 Offline
Activity: 182
Merit: 100
May the source be with you.
|
|
April 20, 2015, 01:17:34 PM |
|
AFAIK there is no working solution to running S5 off SD card. There are instructions for recovery via SD but its not a full restore and will only work in some cases.
The recovery image has a reflash script in it that should fully re-image the emmc. It should work in all cases where the beaglebone hardware is undamaged. It would appear it first zeros out the emmc then copies the firmware files from itself. You can look at /etc/init.d/initc_emmc_flash.sh to see the rest of how this seems to be done. Last I remember you could keep running it off of the SD card after this process but I haven't checked in a while. It would actually be fairly easy to remove part of this script so it just keeps running off of the SD card and doesn't flash the emmc in case you didn't want to touch the internal memory. Hmm. When I tried it it didn't appear to do anything. Maybe my board was more than just a software brick. No, it's just your usual waffle. If you do not know something, don't comment rather than confuse users with your ignorance. Can someone that knows please tell me how to set voltage on an S5? I have tried setting it via the cgminer config file and restarting cgminer but the API still reports a voltage of 0725 String design, you must raise voltage on your psu. Simple formula vin/15=voltage per chip |
|
|
|
|
Tupsu
Legendary
Offline
Activity: 1218
Merit: 1003
|
|
April 20, 2015, 02:40:40 PM |
|
You're doing right reminding people about that they can loose warranty. I live in Russia so warranty for me is usless and i know how such things works, so i can repair it easly, as i mentioned i don't care  1. With Four blade, he can not turn itself off at 80 degrees. 2. This soft is not been able to work with three-or four-blade . example http://www.perearstike.ee/S5/4.blade.Sm.jpg |
|
|
|
|
smit1237
Full Member
Offline
Activity: 182
Merit: 100
May the source be with you.
|
|
April 20, 2015, 03:53:48 PM |
|
You're doing right reminding people about that they can loose warranty. I live in Russia so warranty for me is usless and i know how such things works, so i can repair it easly, as i mentioned i don't care 1. With Four blade, he can not turn itself off at 80 degrees. 2. This soft is not been able to work with three-or four-blade . example http://www.perearstike.ee/S5/4.blade.Sm.jpgI don't have spare blades, so i've can't test this setup. And this is for s5 not double s5 btw. No one provides feedback until something dangerous happens. I think i shouldn't do that i do. Better to keep it private. |
|
|
|
|
|
pekatete
|
|
April 20, 2015, 04:22:54 PM |
|
I don't have spare blades, so i've can't test this setup. And this is for s5 not double s5 btw.
No one provides feedback until something dangerous happens. I think i shouldn't do that i do. Better to keep it private.
@smith1237 - don't stop, your work is very good. Keep sharing and those that can use your firmware in an informed way will never get any issues. Experienced users who use it for the wrong purpose without testing first have only themselves to blame. |
|
|
|
smit1237
Full Member
Offline
Activity: 182
Merit: 100
May the source be with you.
|
|
April 20, 2015, 05:26:20 PM |
|
I don't have spare blades, so i've can't test this setup. And this is for s5 not double s5 btw.
No one provides feedback until something dangerous happens. I think i shouldn't do that i do. Better to keep it private.
@smith1237 - don't stop, your work is very good. Keep sharing and those that can use your firmware in an informed way will never get any issues. Experienced users who use it for the wrong purpose without testing first have only themselves to blame. Youre right, but now i must scream at all corners this firmware for advanced users and blah blah blah. Sad, that people don't realize simple thing that this firmware not official, so no guarantee not to fry something  Btw that's the reason i think, why bitmain stay at cgminer 4.8.0 i should keep an eye on their github repo for updates |
|
|
|
|
Tupsu
Legendary
Offline
Activity: 1218
Merit: 1003
|
|
April 20, 2015, 08:01:43 PM |
|
Youre right, but now i must scream at all corners this firmware for advanced users and blah blah blah. Sad, that people don't realize simple thing that this firmware not official, so no guarantee not to fry something Btw that's the reason i think, why bitmain stay at cgminer 4.8.0 i should keep an eye on their github repo for updates Luckily my 4 blades all working , but I got more, as 120 degrees Celsius , after syscooling pump failure. This is the first time that I had to replace the hoses after miner overheating. I'm even pleasantly surprised, that all 4 blades survived. After remove the hoses, came out only hot steam and boiling water  The warranty is only 90 days , shipped 2015-01-13. So is warranty already over. I have several S5 built to 4 blades. Water-cooled and also the air-cooled models. 2,3 TH/s miner is better than the 1,15 TH/s, if I have a total of 35 Antminer S5. The only problem is that You began to modify Bitmaintech first S5 software. The first software does not support 4 blade. All of the following Bitmaintech S5 software versions supporting 3 or 4 blades at one S5 controller. |
|
|
|
|
toptekk
Member
Offline
Activity: 112
Merit: 10
|
|
April 20, 2015, 11:30:26 PM
Last edit: April 20, 2015, 11:44:39 PM by toptekk |
|
I see the S4 + is out not a bad price wondering if well see a ANTMINER S5+ with improved cooling and maybe at 1.8 or 2 th maybe ,,, hoping hoping. at about the Same S5 price   ? . Idc what power it uses at this point i have to start using a 240 line to many miners on my 110 lines time to start using the 240 line , i had put in . . |
|
|
|
|
toptekk
Member
Offline
Activity: 112
Merit: 10
|
|
April 20, 2015, 11:40:22 PM
Last edit: April 21, 2015, 01:41:25 AM by toptekk |
|
Actually my firmware based only on official sources(cgminer) i only add some nice looking graphs and tweaked a bit cgminer code to better support nicehash(revert old patch, apply new patch). Bitmain testing my firmwares, but looks like they decided to use old cgminer(dunno why, they don't told me ). In next release i plan to add crontab as many people asking me to do so. nice to hear i hope it goes your stuff is nice . Smit1237 one of my S5 i have to use bitmains official firmware on or it does some really strange stuff if I use yours on it but my other S5 work better with your version then the official firmware, i never told you about sense it works fine with there firmware, i did not see a need to say anything. i just wish they would fix #xnsub so it worked every were like yours does and not just on a few sites. bitmain it is out of warr so no bigie it still works fine, as long as i use your firmware on that one . |
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
April 21, 2015, 07:38:21 AM |
|
might have figured out where that resistor went.. one of my hashing boards shut off earlier. no X's or anything, all o's.. it just stopped working.. the red light was off and the miner was running around 600 ghs and the board was only 28c.
i turned it off and back on and it started back up again. i guess ill keep an eye out on it.. maybe ill try the new firmware.
|
|
|
|
|
|
muhrohmat
|
|
April 21, 2015, 09:30:48 AM |
|
could some of you guys put the price and roi estimated of this relation ships of this ant miner s4 and s5 it seems it takes like 8 months to roi and the watts my god sorry my mining skills are not that big
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
April 21, 2015, 10:03:50 AM |
|
could some of you guys put the price and roi estimated of this relation ships of this ant miner s4 and s5 it seems it takes like 8 months to roi and the watts my god sorry my mining skills are not that big
you will never ROI the S4+ or S5 unless you have other miners to help. unless you have completely free energy.. then it will take like 215+ days. at this point it is best to buy BTC and hold it. |
|
|
|
|
coinits
Legendary
Offline
Activity: 1582
Merit: 1019
011110000110110101110010
|
|
April 21, 2015, 12:31:10 PM |
|
could some of you guys put the price and roi estimated of this relation ships of this ant miner s4 and s5 it seems it takes like 8 months to roi and the watts my god sorry my mining skills are not that big
you will never ROI the S4+ or S5 unless you have other miners to help. unless you have completely free energy.. then it will take like 215+ days. at this point it is best to buy BTC and hold it. Two words for you: Resale Value |
Jump you fuckers! | The thing about smart motherfuckers is they sound like crazy motherfuckers to dumb motherfuckers. | My sig space for rent for 0.01 btc per week.
|
|
|
soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
|
April 21, 2015, 03:57:13 PM |
|
AFAIK there is no working solution to running S5 off SD card. There are instructions for recovery via SD but its not a full restore and will only work in some cases.
The recovery image has a reflash script in it that should fully re-image the emmc. It should work in all cases where the beaglebone hardware is undamaged. It would appear it first zeros out the emmc then copies the firmware files from itself. You can look at /etc/init.d/initc_emmc_flash.sh to see the rest of how this seems to be done. Last I remember you could keep running it off of the SD card after this process but I haven't checked in a while. It would actually be fairly easy to remove part of this script so it just keeps running off of the SD card and doesn't flash the emmc in case you didn't want to touch the internal memory. Hmm. When I tried it it didn't appear to do anything. Maybe my board was more than just a software brick. No, it's just your usual waffle. If you do not know something, don't comment rather than confuse users with your ignorance. Can someone that knows please tell me how to set voltage on an S5? I have tried setting it via the cgminer config file and restarting cgminer but the API still reports a voltage of 0725 String design, you must raise voltage on your psu. Simple formula vin/15=voltage per chip May I ask what you mean by string design? The ASICs are in series? Then the S3+'s are also string design? I have a dead S3+ beyond warranty I'm trying to fix. |
|
|
|
|
|
dog1965
|
|
April 21, 2015, 05:02:16 PM |
|
AFAIK there is no working solution to running S5 off SD card. There are instructions for recovery via SD but its not a full restore and will only work in some cases.
The recovery image has a reflash script in it that should fully re-image the emmc. It should work in all cases where the beaglebone hardware is undamaged. It would appear it first zeros out the emmc then copies the firmware files from itself. You can look at /etc/init.d/initc_emmc_flash.sh to see the rest of how this seems to be done. Last I remember you could keep running it off of the SD card after this process but I haven't checked in a while. It would actually be fairly easy to remove part of this script so it just keeps running off of the SD card and doesn't flash the emmc in case you didn't want to touch the internal memory. Hmm. When I tried it it didn't appear to do anything. Maybe my board was more than just a software brick. No, it's just your usual waffle. If you do not know something, don't comment rather than confuse users with your ignorance. Can someone that knows please tell me how to set voltage on an S5? I have tried setting it via the cgminer config file and restarting cgminer but the API still reports a voltage of 0725 String design, you must raise voltage on your psu. Simple formula vin/15=voltage per chip May I ask what you mean by string design? The ASICs are in series? Then the S3+'s are also string design? I have a dead S3+ beyond warranty I'm trying to fix. Series exactly is a more pro term for it then "STRING". |
|
|
|
|
montyfd
Member
Offline
Activity: 60
Merit: 10
|
|
April 21, 2015, 06:47:34 PM |
|
I have 20 S5 running since one week.
ALL of them freqently (within 12-24 hours) get "lost.
I cannot acces them through webinterface and not trhough putty.
They are mining (all lights show normal operation and they are hot), but NOT at my pools. No hashrate there.
I have restart them by pulling power, then they work again normal for a few hours.
Running different firmwares, happens with all of them. None of the other miners (S2s, S3s) is doing this.
Makes me think if i bought 20 pieces of crap or if somebody guilt in a backdoor to have them mining for somebody else frequently.
I cant watch the miners 24 hours a day and then drive over to trhe place to pull power twice a day.
No answer from bitmain.
Anybody with similar problems or a solution?
|
|
|
|
|
smit1237
Full Member
Offline
Activity: 182
Merit: 100
May the source be with you.
|
|
April 21, 2015, 07:45:17 PM |
|
I have 20 S5 running since one week.
ALL of them freqently (within 12-24 hours) get "lost.
I cannot acces them through webinterface and not trhough putty.
They are mining (all lights show normal operation and they are hot), but NOT at my pools. No hashrate there.
I have restart them by pulling power, then they work again normal for a few hours.
Running different firmwares, happens with all of them. None of the other miners (S2s, S3s) is doing this.
Makes me think if i bought 20 pieces of crap or if somebody guilt in a backdoor to have them mining for somebody else frequently.
I cant watch the miners 24 hours a day and then drive over to trhe place to pull power twice a day.
No answer from bitmain.
Anybody with similar problems or a solution?
Set "static" lease for every miner mac address. |
|
|
|
|
montyfd
Member
Offline
Activity: 60
Merit: 10
|
|
April 21, 2015, 07:59:34 PM |
|
They all run static ip  |
|
|
|
|
GrumpyBear2
Newbie
Offline
Activity: 27
Merit: 0
|
|
April 21, 2015, 08:25:14 PM |
|
On your router make sure you have assigned those static IP’s (usually give them a name on the router: Ant_1, Ant_2….). So the router knows not to change or re-assign those IP’s in the future.
Me, I also have MAC filtering on, so I have to assign them on the router too.
|
|
|
|
|
|
