over 1/3 tokens sold, not bad... hope you will sell all 30 million tokens.
The ICO looks to be a good chance to sell at least 20 million tokens. |
|
|
|
Tried contacting sellers before they don't respond, feels sketchy to me buying from China tbh.
Yep, generally DAF and good luck getting a refund or any customer service from most of these 'vendors'  |
|
|
|
Nice, out of interest what is your electricity cost? Are you hosting at home or in a data centre? |
|
|
|
Not at this stage unless you have an advantage versus the competition. Just buy your choice of coin(s) directly at this stage, lock them away securely, then check back in a years time  |
|
|
|
To answer the OP:
ASROCK AB350 Pro 4 - Craps out after 4 cards. Will POST, but Windows won't complete boot. Tried using M.2 adapters and everything, but it didn't work. Maybe in the future with bios updates.
I had no issues getting the AB350 Pro 4 to detect and mine with 6 x GPU's running EthOS. I could not get past 4 cards Did you change anything at Bios? If yes, could you tell us what has changed? I thank you Not that I remember, it was quite a while ago that I set the board up though. It has 5 x GPU's running without issues, and I expect it would do 6 if I had a PSU here to support adding a 6th GPU. |
|
|
|
I haven't found a efficient way to use the 1080ti.
ETH hashrate is low, about 35 MH/S. DGB-skein hashrate is high, about 950 MH/S, but the price of GDB becomes lower, any ideas? Which coin do you mine using the 1080ti?
Zcash is one of the best coins to mine with NVIDIA GPU's, including the 1080 Ti. |
|
|
|
To answer the OP:
ASROCK AB350 Pro 4 - Craps out after 4 cards. Will POST, but Windows won't complete boot. Tried using M.2 adapters and everything, but it didn't work. Maybe in the future with bios updates.
I had no issues getting the AB350 Pro 4 to detect and mine with 6 x GPU's running EthOS. |
|
|
|
The AB350 pro 4 works with 6 GPUs, I have 2 along with a ryzen 7 in both
I confirm this too, tested and working with Ryzen 5 1400. |
|
|
|
If you are up to it... I would love to know your full specs and how it is arranged.
I can't give all my tricks away, to be fair I have shared a lot more already than I normally would |
|
|
|
damn, just looked it up and it's not cheap
It's only $39 USD which is cheaper than Windows and its worth the money. You pay for what you get (and don't get)..  |
|
|
|
Awsome rig, dude, do you use 2 psu 1600w for this rig? And can you share what kind of MOBO you use please?
2 x EVGA 1300 G2 PSU 1 x EVGA 1200 P2 PSU Note that I just used what I had on hand, 3 x 1200W PSU's would do the job. Motherboard is SMC X9DRX-F with 2 x Intel E5-2620 CPU's and 8 x 8GB DDR3 ECC RAM modules. |
|
|
|
how many volts are risers using?
What about the "issue" I've read on here that the motherboard and risers should have the same power source?
PCIe powered risers with a 6-pin PCIe power connector are 12V. PCIe powered risers with a Molex power connector are 12V. PCIe powered risers with a SATA power connector are 5V. |
|
|
|
I have 6 MSI rx570 card and asus z270p motherboard
Here is the problem I can't see all cards in windows platform
if I turn on the above 4g decoding in windows, system fall into eror an restart windows again and again
My 6 card works simplemining.net right now so motherboard seems to be support 6 card
but I want to install ubuntu and works all my cards in there I think ubuntu is much easier and painless than windows
I tried install ubuntu and drivers but I can't set some overclock definitions and fan speed.
What is your suggestions can you help me ?
Obtain a copy of EthOS from gpuShack and use that, it supports overclocking and will be better than Windows, and easier than configuring Ubuntu Linux yourself. |
|
|
|
Yeah i am pretty sure he knows how to set something like that up.
That wasn't the question.. Why don't you offer to lend him a hand |
|
|
|
Nothing particularly special, here are the settings: nvidia-smi -pm 1
nvidia-smi -acp 0
nvidia-smi -pl 300
nvidia-settings -a GPUPowerMizerMode=1
nvidia-settings -a GPUFanControlState=1
nvidia-settings -a GPUTargetFanSpeed=100
nvidia-settings -a GPUGraphicsClockOffset[3]=100
you put those in the bat file or in the cfg file? I am running Ubuntu Linux, so it goes into a .bash file. |
|
|
|
I mine in my garage (see the server rack in photo below) and have absolutely no issues with heat at all. mind you.. I live on the side of a mountain in Colorado at 8000ft   cheers, Ed Nice setup! |
|
|
|
Pretty sure they stopped selling them and are mining with them themselves at the moment.
They have massive supply issues with AMD GPU's and a load of orders to get through. And yes, they could be mining themselves  |
|
|
|
|
They only have 6 x 8-pin PCIE power connectors shared between GPU's and CPU's, this means you can only have 5 connectors dedicated to GPU's.
|
|
|
|
|
What you need here is a 'splitter contract' to split the earnings to two different wallet addresses.
|
|
|
|
|
Show Posts
