So, the z750 supplies work under heavy load. Typically a computer supply will claim a certain wattage capability and on the side list the current available on each voltage but don't supply that total wattage to any one voltage.
In switched mode, the z750 has a single rail 12v @ 62.4A which equates to 748.8W. In standby mode it is 3.3v @ 5.5A which equates to 18.15W
|
|
|
Fan mod 1. Thermalright 130CFM pull - fan is PWM but run with blue wire hack, aka full pelt) 2. Stock S3 fan running on PWM - push This is a strange setup, during the day when it is a bit warmer, the push fan (stock S3) runs at higher RPM (3600 max I've seen) and I get temps of 44 and 46. Freq 412.5 And when the push stock S3 fan ramps up to 3600 rpm .... (first time I've noticed it at night!) temps fall to 40, 43
|
|
|
wow awesome freq with very low temps ho much power to do it?
I use 2 550W Dell server PSU's, one for each blade. great.. i will try it on my s5. did you mod the bitmain-voltage in cgminer.conf? No I have not and it is running on the default voltage setting, but now that you mention it (and I am sure I have adequate power and cooling), I'll look into changing / setting different voltages.
|
|
|
wow awesome freq with very low temps ho much power to do it?
I use 2 550W Dell server PSU's, one for each blade.
|
|
|
Fan mod 1. Thermalright 130CFM pull - fan is PWM but run with blue wire hack, aka full pelt) 2. Stock S3 fan running on PWM - push This is a strange setup, during the day when it is a bit warmer, the push fan (stock S3) runs at higher RPM (3600 max I've seen) and I get temps of 44 and 46. Freq 412.5
|
|
|
Interesting. Batch Five is now sold out.
Nope, batch 5 is now / still available ...
|
|
|
Ugh. Nevermind. Like talking to a stone wall. I'll be the mature one and move on. Is that OK with you?
Now that you realise your nonsensical comments to be that ... do as you wish. Just don't delude yourself that you know it all, if anything, bitchie dogie. PS. That heatsink mod I described above was accomplished with no more than a power drill, snips and the trusty dremel that I used for tapping the holes ... so there you have it!
|
|
|
It 'has to do with me' when you attacked me for no reason. If you don't like what I'm posting, ignore me like I do to you.
And this is what you take to be an attack? .... I wish a company made a copper option with heatpipes, could make a huge difference for overclocking.
Heatpipes aren't something you can do yourself easily, they're not very use friendly to craft. Generally though, there wouldn't be much point making extreme stock heatsinks which add $40 and 400g of weight to everyone elses shipments when their additional capacity is going to be used by very few. You've raised your ugly head again ..... If you find dealing with heatpipes difficult, leave it to those who don't (both in practice and comments). No one asked you to add these to your homebrews, and unlike you, most people are not penny-pinching skinflints .... At least you do not distance yourself from bitchie .... you 2 are one and the same .... but like I said, if you find heatpipes difficult, leave it to those that don't. You do not have to throw in your 2 cents into any and everything all the time, mostly with your ignorance. For starters, my suggestion was a self moded copper heatsink, and I speak WITH experience here as I have a few aluminium slab + copper fins heatsinks that I made myself. The fins were made from split copper tubes and attached to the aluminium using screws and heatpads. Whether it costs more or not, you have no way of telling and therefore are not in a position to add any value to the conversation, thus has nothing to do with you. Millionaire at 13, went to MIT and left to work in family machine shop programming CNC's and wire EDM's bitchie dogie .....
|
|
|
Ofcourse, you need tools (that's a no-brainer) ... a dremel would be a good start .... but definitely not a task to be undertaken by feeble minded at DIY. But like I said, not that hard (does not mean it is easy!)
Having worked at my family's machine shop, programming CNC mills/lathes and Wire EDM's for a few years, if you can do what you're saying with a dremel and have it actually work, I'm sure we ALL would love to see that. Indeed. Pekatete is clearly so much better than us that I'd love for him to teach us how to manufacture high grade heatpipes from scratch. Because its easy, you know. What on earth has it to do with you (dogie and bitchie) if it costs more or is hard to fabricate? This is a case of nit-picking gone mad. The initial post was somebody wondering whether a copper heatsink would work better, and I actually concur with them as copper is a better heat conductor than aluminium, but of course (EVERYBODY KNOWS THIS!) more expensive. And for a person who claims to have worked in a family machine shop, apparently programming CNC mills and wire EDM's, this has to be a walk in the park! But hey, there have also been claims of people being millionaires at 13 and I would not be surprised if the two (pathological liars) are the same person.
|
|
|
.... I wish a company made a copper option with heatpipes, could make a huge difference for overclocking.
Should not be that hard to fabricate on your own .... just need to find out what thickness of the copper slab to get, slice some slots / channels in it and then split a few copper tubes to for the fins that are slid into the slots. All you are left to do is drilling tapped holes for attaching the PCB. I wonder how cost efficient it would be though for just a handful of units ..... ? Doesn't sound that easy to me. Unless you have a machine shop and all the tools necessary as well as the skills to do properly. Heatpipes aren't something you can do yourself easily, they're not very use friendly to craft. Generally though, there wouldn't be much point making extreme stock heatsinks which add $40 and 400g of weight to everyone elses shipments when their additional capacity is going to be used by very few. You've raised your ugly head again ..... If you find dealing with heatpipes difficult, leave it to those who don't (both in practice and comments). No one asked you to add these to your homebrews, and unlike you, most people are not penny-pinching skinflints ....
|
|
|
.... I wish a company made a copper option with heatpipes, could make a huge difference for overclocking.
Should not be that hard to fabricate on your own .... just need to find out what thickness of the copper slab to get, slice some slots / channels in it and then split a few copper tubes to for the fins that are slid into the slots. All you are left to do is drilling tapped holes for attaching the PCB. I wonder how cost efficient it would be though for just a handful of units ..... ? Doesn't sound that easy to me. Unless you have a machine shop and all the tools necessary as well as the skills to do properly. Ofcourse, you need tools (that's a no-brainer) ... a dremel would be a good start .... but definitely not a task to be undertaken by feeble minded at DIY. But like I said, not that hard (does not mean it is easy!)
|
|
|
.... I wish a company made a copper option with heatpipes, could make a huge difference for overclocking.
Should not be that hard to fabricate on your own .... just need to find out what thickness of the copper slab to get, slice some slots / channels in it and then split a few copper tubes to for the fins that are slid into the slots. All you are left to do is drilling tapped holes for attaching the PCB. I wonder how cost efficient it would be though for just a handful of units ..... ?
|
|
|
Damn... Shipping cost for 1 S5 (to Russia) via EMS became 129.613 USD. Who is crazy - Bitmain or EMS?....... Due to the large quantity of shipments abroad, customs request us to do official customs clearance before exporting. Current shipping cost provided in our website has included the handling fee charged by EMS. Thanks for your understanding. That would be nice if they include the VAT / import duty payments and the courier charges in the shipping cost to the UK, so all we are left with is signing for the item on delivery. PS. Where did you see that quotation?
|
|
|
So... Chance and luck are different things?
Of course! The word "chance" has gambling connotations, while the word "luck" is loaded with superstitious undertones :-) The only difference comes from the perspective of the person you ask. More semantics than anything of substance. Luck is the lay man's term for probability and has nothing to do with superstition. And chance, well, that's just luck! Semantics or not, some of us prefer to use technically correct terms for things. Who's stopping you from saying what you prefer, semantically insubstantial though it may be? Just don't expect the rest of us to be in the same boat as you.
|
|
|
So... Chance and luck are different things?
Of course! The word "chance" has gambling connotations, while the word "luck" is loaded with superstitious undertones :-) The only difference comes from the perspective of the person you ask. More semantics than anything of substance. Luck is the lay man's term for probability and has nothing to do with superstition. And chance, well, that's just luck!
|
|
|
@Pekatete, if your purcahse was within the last 90-days, please e-mail support@bitmain.zendesk.com and attach your Order Confirmation page in PDF with your shipping address information. There is a service center in Serbia that may be able to service you closer than USA. It is just inside 90 days, so I'll send an email to the above address and see what comes of it. Not sure what the wording should be in the email though (seeing it was info@bitmaintech.com who told me to get one from the local market) .... I'd like to get a replacement fan as the shipped one was a DOA .... would that suffice?
|
|
|
@pekatete, dead fan, we do offer replacement. The fans used on Antminer is not an easy one to find as it uses 4 wires and high RPM. We are sorry for the inconvenience. Our USA based team can take care of you faster usually and they are available 24/7. Thank you for the stats!!
52 is a bit warm but it is well in the range.
Not sure you are thanking me, but I'll accept anyway; You are welcome. The 52 refered to is the top temp, i.e with that configuration, the temps never go above 52 during the day (and currently below 48 at night). I actually believed 52 was a brilliant top temp, but I've not had a different temp to compare with as my S5 shipped with a stone dead fan that never turned a fin in anger! I was advised to buy one from the local market (without any hint of irony or any offer for a replacement .... not even a voucher offer!). Better late than never .... but I am not based in the US, rather the UK, so it may be tricky for me to send you the dead fan (which I still have and looks pristine next to the others I salvaged from my now decomisioned S1's!). If on the other hand you can send me the replacement without me having to meet the cost of mailing you the dead one, I'll be more than happy to furnish any info you require.
|
|
|
Thank you for the stats!!
52 is a bit warm but it is well in the range.
Not sure you are thanking me, but I'll accept anyway; You are welcome. The 52 refered to is the top temp, i.e with that configuration, the temps never go above 52 during the day (and currently below 48 at night). I actually believed 52 was a brilliant top temp, but I've not had a different temp to compare with as my S5 shipped with a stone dead fan that never turned a fin in anger! I was advised to buy one from the local market (without any hint of irony or any offer for a replacement .... not even a voucher offer!).
|
|
|
So no cares? Everyone here just talking about fans. I think they are missing the important information and a little delusional.
There are 179 pages in just this thread, and hundreds more (if not thousands) where your so called important information has been exhaustively commented on. You seem to be on a new account (not sure that equates to being new here), so before you castigate anyone and / or lay claim to being the clearest mind on the forum (I concur, being here can muddle your thinking), we are all eyes for your pearls of wisdom!
|
|
|
To get involved or not involved.
Give me your number ... I'll call you, maybe! One way you'll be involved, I don't have to tell you what the other way will be (I think).
|
|
|
|