Hi Guys, Something seems wrong, Can someone check my link to see if everything is ok? I mined for a FULL 24 hrs since last payout and I got an even less amount to what I got yesterday and yesterday CGminer closed on me for a few hours, So I wasnt mining for atleast 3 hrs. I was expecting This payout to be ATLEAST .02 I am on 1.5mhz and it has shown me on the main page as Exactly 0.7270 for 48 hrs now. I only got 0.0174 Which is pretty low.. I checked on a few other guys with 1.5mhz and they have atleast 0.02? http://middlecoin2.s3-website-us-west-2.amazonaws.com/reports/1Ebrs5hygiN2oT7AqYJbVGPCXp6z9tuuQ2.htmlOne other thing - Is there a way we can see how much we mined without the fees taken out it seems the exact amount showing on your graph is the exact amount that gets transferred. How do we know the correct fees are being taken out and not 5-7%? Is this all just based on trust? Some days are better than others. There are many factors that can make the payouts more or less. My payout yesterday was: 0.07641323 Today's payout was: 0.07018740 Like you I also had a bit of downtime yesterday to as shown on my chart. http://middlecoin2.s3-website-us-west-2.amazonaws.com/reports/14e7qwzHbdLMdGJz7XcAG6oTMNtqTpn3Yv.htmlDont you mean your payout today was 0.05444536 ?? And Also i dont know if you would even call that down time, You were still hashing. Look at my down time... You know what ? maybe yesterday I would of got over 0.02 if it were not for those 3 hrs Down time... I will leave it on for a few days.. See whats the go. My bad, for some reason my page was not refreshed properly. I had to F5 it to see it. So yes my payout today was 0.05444536 By downtime, I meant one of my rigs was down. Others were still hashing though. |
|
|
|
Hi Guys, Something seems wrong, Can someone check my link to see if everything is ok? I mined for a FULL 24 hrs since last payout and I got an even less amount to what I got yesterday and yesterday CGminer closed on me for a few hours, So I wasnt mining for atleast 3 hrs. I was expecting This payout to be ATLEAST .02 I am on 1.5mhz and it has shown me on the main page as Exactly 0.7270 for 48 hrs now. I only got 0.0174 Which is pretty low.. I checked on a few other guys with 1.5mhz and they have atleast 0.02? http://middlecoin2.s3-website-us-west-2.amazonaws.com/reports/1Ebrs5hygiN2oT7AqYJbVGPCXp6z9tuuQ2.htmlOne other thing - Is there a way we can see how much we mined without the fees taken out it seems the exact amount showing on your graph is the exact amount that gets transferred. How do we know the correct fees are being taken out and not 5-7%? Is this all just based on trust? Some days are better than others. There are many factors that can make the payouts more or less. My payout yesterday was: 0.07641323 Today's payout was: 0.07018740 Like you I also had a bit of downtime yesterday too as shown on my chart. http://middlecoin2.s3-website-us-west-2.amazonaws.com/reports/14e7qwzHbdLMdGJz7XcAG6oTMNtqTpn3Yv.html |
|
|
|
It was for 0.25 BTC and I don't think the original poster will even see this thread to be honest  |
|
|
|
So... I've installed my 280x (ASUS R9280X-DC2T-3GD5) yesterday and having a hard time to get more than 575-600 kh/s with it.
Windows 7
Catalyst 13.12
cgminer 3.7.2 with:
"gpu-threads" : "2",
"intensity" : "13",
"worksize" : "256",
"shaders" : "2048",
"thread-concurrency" : "8192"
GPU core clock is 1070mhz
CPU mem clock is 6400mhz
GPU temp is around 74celcius (fan at 55%)
Increasing Intensity gives me hardware errors
what else can be done?
Add: "gpu-powertune" : "20" Also overclock your GPU memory as far as it will go. If that fails to give you the desired results then try "gpu-threads" : "1", "intensity" : "20", "worksize" : "256", "thread-concurrency" : "22400" "gpu-powertune" : "20" |
|
|
|
I use a mixture of cudaminer and cgminer across several workers.
They all point to a local stratum proxy using the above flags.
That sounds way too advanced for me to help you out. why do you have a local stratum? there's absolutely no reason to. I have a lot of hardware "all over the place" and it's much easier for me to have them all connect to a local server where I can control what pool and user/pass I am connecting all my workers with in one spot. Manually changing a pool or user/pass on each of my workers would take me probably an hour+ of connecting monitors and keyboards around the house. This is what the stratum proxy was designed for, and I use it all the time with other pools. It works great. I am sorry if I missed it in one of your previous posts but I am assuming that you are using Linux because if you are on windows then the solution to your problem is Teamviewer. You probably already know this though and are using Linux anyway I bet. |
|
|
|
Any ideas why I am hashing around 4.2MH/s but it only says I am hashing around 3.1MH/s ?
Also, when I check CGMiner, I get a lot of stratum from pool 0 detected new block.... then the same message then maybe an accept then another few lines of new block detected? Is there something wrong ?
All normal. Rates on the site will fluctuate. |
|
|
|
Just use -d option like:
cgminer blah blah -d 0 -g 2 -d 1 -g 1 ....
Card 0 will have 2 thread and card 1 will have 1 thread.
Thanks a lot man!! Finally my multicard rig can work with one instance! I am fairly certain that you cannot do it this way. You need to run another instance of cgminer to run different thread settings. Yea you right, I was happy too soon, the crappy card still shows two threads. How is the hash/s for each card, good or not ? I get exactly the same hash/s with multicard and -d (--device not disable) like every card in a single card setup. Don't know if they really get 1 or 2 thread but the result say me it's working. Click on the cgminer command window frame and then hit the 'G' key and it will list the cards and thread counts. |
|
|
|
The two 7970's running at 788= 1130 core / 1745 mem, I 13, G 2, 8192 tc. Brand is XFX on these.
The one 7970 running at 746= 1070 core / 1690 mem, I 13, G 2, 8192 tc. Brand is HIS
The lame 7970 running at 540= 1050 / 1500, I 13, G 1 (will not run at g2) 8192 tc. Brand is HIS
The two 290x's running at 880= 900 core / 1495 mem, I 20 , G 1, 32765 tc. Brand is XFX on these. Pretty impressive on that XFX brand 7970. I can only get around 700 KH/s. http://zsprawl.com/iOS/2013/12/mining-bitcoins-in-esxi-using-an-xfx-7970/They have been running great for me. No complaints so far.   |
|
|
|
It is gone now. Coingeek must be playing with the graphics. |
|
|
|
With intention |
|
|
|
I might have missed this over the last few days, but whats with the little half moon that now appears on my page graphics???
Possible reference to the term: "To tha moon" |
|
|
|
Isnt multipool only mining the most profitable coin at one time? can you choose what you want to mine on there?
You can manually choose one of the coins there if you want |
|
|
|
Do a bunch of small buys with PP, wait 30, 60 or 90 days then do multiple charge backs citing these were unauthorized = $$$$$$ This is why PP is frowned upon. This happens everyday despite multiple warnings and yet it continues. Ever wonder why some have no pity on the scammed? Care to venture a guess?
+1 Happens all the time. The OP saying he is trustworthy means nothing at the end of the day. Try explaining to Gaypal that the buyer said he was trustworthy and had x amount of trades and see what response you get back. |
|
|
|
|
This thread is for the 280x
For the 290x you could use:
/cgminer --scrypt -I 20 -g 1 -w 512 --gpu-engine 900 --gpu-memclock 1500 --gpu-powertune 20 --thread-concurrency 32765 -o stratum+tcp://xxxxxxx -u xxxxxxxx --no-submit-stale
That should get you 800+
|
|
|
|
|
You need to over clock your memory too. See if you can get it to 1700 on the mem. Or as high as you can. So something like 1050+/1700.
If you can do that then you should be able to run in the 700's using:
/cgminer --scrypt -I 13 -g 2 -w 256 --gpu-engine 1050 --gpu-memclock 1700 --gpu-powertune 20 --thread-concurrency 8192 -o stratum+tcp://xxxxxxx -u xxxxxxxx --no-submit-stale
Or alternatively you could try this for -I 20 -g 1:
/cgminer --scrypt -I 20 -g 1 -w 256 --gpu-engine 1050 --gpu-memclock 1700 --gpu-powertune 20 --thread-concurrency 22400 -o stratum+tcp://xxxxxxx -u xxxxxxxx --no-submit-stale
|
|
|
|
yes the animal coins are making a farce out of the serious business of pumping and dumping shitcoins.
This. +2 |
|
|
|
Just use -d option like:
cgminer blah blah -d 0 -g 2 -d 1 -g 1 ....
Card 0 will have 2 thread and card 1 will have 1 thread.
Thanks a lot man!! Finally my multicard rig can work with one instance! I am fairly certain that you cannot do it this way. You need to run another instance of cgminer to run different thread settings. Yea you right, I was happy too soon, the crappy card still shows two threads. Oh I see so I still need to run two instances of cgminer but the -d just tells each instance which cards it is controlling. I can still see this being a pain in the arse with bamt though. I might install some other linux distro and get a separate monitor program. -d tells it which card to disable. --remove-disabled removes the disabled card from the cgminer display otherwise you will have a card showing 0.000 Mhz and it hinders the performance of the card that is running. according to https://bitcointalk.org/index.php?topic=28402.0, the -d tells it which device to use... --device|-d <arg> Select device to use, one value, range and/or comma separated (e.g. 0-2,4) default: all Can you please stop spreading misinformation =] kthx My bad, sorry. The method is still sound even though I confused the -d flag meaning. So an example bat file would look like so:
Card one that only likes G 1:
cgminer.exe --scrypt -o stratum+tcp://eu.middlecoin.com:3333 -u 14e7qwzHbdLMdGJz7XcAG6oTMNtqTpn3Yv -p x -d 0 -I 13 -g 1 --gpu-engine 1050 --gpu-memclock 1500 --gpu-fan 100 --thread-concurrency 8192 -w 256 --gpu-powertune 20 --no-submit-stale --remove-disabled
Card two that likes G 2:
cgminer.exe --scrypt -o stratum+tcp://eu.middlecoin.com:3333 -u 14e7qwzHbdLMdGJz7XcAG6oTMNtqTpn3Yv -p x -d 1 -I 13 -g 2 --thread-concurrency 8192 --gpu-engine 1070 --gpu-memclock 1700 --gpu-fan 100 -w 256 --gpu-powertune 20 --no-submit-stale --remove-disabled
Just trying to help, which I think I have. =] kthx |
|
|
|
|
Show Posts
