thanks sebastian for update.
we all did it! i believe the latest scam postings on bitsyncoms profile did help alot and our constant pushing.
well done people.
now what to buy?

im sure he will take care of responses on email..

I won't bid without escrow. and prefer with PSU.

hes answering his own posts.. not even mining to selling address.. scam.

this sold? im interested in one module for b2.

Hehe! don't leave the refund space. It will only get processed once a full 10k batch has been filled as refund status if i read steamboat right.. And then he will post a refund ticket with bitsyncom, and then if they process for us, we'll get paid in turn..

 (and then, those who dont want refund from batch 6, will be pushed up to batch 5, and if he fills the entire amount for batch 5 for refund they will be pushed to batch 4..)

You can bring your laptop, and send btc when you get the goods..
However, I do believe this to be a scam.

question, im sure its been answered a thousand times, but the rejection rate, i see it a bit high now?
a:5929 r:434
but maybe it settles as ive read? running avalon-auto.

346 1800 2280 2400 21 46 46

i'll see in a while if it goes up to 350 as temp is ok, if it settles on a lower rate as previously shown in past of this thread.

4 hours in, and its still on 10% reject. That normal? on b2 3 unit, i now get 70avg instead of 80..
and its not hot, running 342mhz.
im setting --avalon-freq 340-355 to test..

works alot better with std freq 340, and avalon-freq 340-365.. 0.7% rejects.. temp 24 48 49.
Next il try std 350 and 350-375 or 380.

Well done steamboat, thanks for update. Asicminer drop in blades, will for sure make these batches not roi for most of us.. even if delivered today.
I emailed for my refund. I hope now some of you gets your chips delivered faster, as the last batches will get refunded as yifu (hopefully) processes them and put your line in the queue further up.

to prove yourself, put all the 6x avalons on mining to your own address at eligius! 1MxZmNSnspm2Ya5upvFvW9vQsyr8W76GWf
Then we will all see your hashing power..

Yeah, i'd go with a refund. And maybe invest in something on hand.

So, if your interested, i have a poll in my footer.. But, mining is dead from now on..  Refund must be the only option.

hi,
i now got it on lan (after wifi not working well at all), but somehow, the lan ip was not working, i think i set the broadcast address wrong (since my hosting center has /28 subnet)
Anyway, i now reset it in to failsafe mode (ip became 192.168.1.1 as openwrt says ,not 192.168.0.100 as avalon says).
however, when i try command firstboot, i get this:
root@(none):/# firstboot
/sbin/firstboot: line 3: /sbin/jffs2reset: not found

Any idea how i can get it back to the working firmware with preset ip of 192.168.0.100? so i can login and set the new ip once again?
Thanks for help. Winning help gets minimum 1 hour of mining. (b2 3 unit 82gh)

EDIT: (this is where you set ip in openwrt if you entered it wrong)
vi /etc/config/network
config interface 'lan'
        option ifname 'eth0'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.0.100'
        option netmask '255.255.255.0'
        option gateway '192.168.0.1'
        option broadcast ''
        option dns ''

No deal winner this time..

i think i found the cause of my problem, i read somewhere, that the current is not strong enough to the wifi unit, and since i dont have an antennae, its around 30% reception only. this makes the connection strong in the beginning (before overclocking kicks in), and when OC is on max, there is not enough for the wifi, and then it starts slowly dying off.. it takes around 30min to one hour to go from 100% hash speed down to basically thousands of hashes.. will try lan tomorrow. but annoying as it worked just fine for three days!

I'd imagine that also. since b2 readings are not on chip and should be 20dgrs cooler than chip. at 50+ your chip reading should be 70+.

I will leave all temp settings out then. However, what could be the reason for it to just stop mining? fans are not going high at all.
Could it be connectivity that dies? Its on wifi for now.
Thank you for your time!

After a few hours off, it connected cgminer (i did no changes of firmware, i still run the 0821 version). i now have it on std freq 300, avalon-auto 300-350 avalon-fan 80 , or should i do 100 on fan? its damn noisy..
heat says 30,40,40, so i believe its 40,60,60? ill let it run a few hours, and then check heat again and maybe put fan on 90?
It was on for a while, then it stopped hashing again.. i am fearing that its the wifi thats not connecting too well. or is it really overheating with 300-350 on fan at 80%?

Thanks, i will try it later. I even tried standard chip freq 280, and without --avalon-auto..
Just doesnt seem to connect to cgminer?

Applying changes
Loading /etc/config/cgminer

its just stuck there! just reflashed to factory defaults, it gets an ip from the wifi.
[Firmware Version] => 20130821
cgminer-70bc62c
luci-d854edc+
cgminer-openwrt-packages-800cc58
Socket connect failed: Connection refused

thats what cgminer api says.
ive tried waiting for 2 minutes.. and restart. it was working fine for 3 days straight.
should i try an older firmware?

Hi,

batch2 does not have proper chip heat reading? so the 20, 40, 42 reading in reality is 40, 60 and 62 reading?
It ran fine for 3 days straight, then it just went to zero hashing.. and restarting it gets back to hashing a while, then goes down again.
--avalon-auto freq 300-355
what is best fan setting? it is in a 20dgr ac room..