What can be problem then? I notice, when I erase old .bin file and put new one, after restarting rig old .bin file shows up again on same place, and then I have 2 bin files in same folder, miner using old bin file ofc...
This is what I'd try: Remove all bins from folder. Start miner. Stop after first hash. Copy name of bin file just created. Rename new bin with that bin name you just created. Do not have del *.bin in .bat file. Try that. |
|
|
|
how can i disable 1 card in this sgminer?
Press "g" then "disable" then pick gpu how can i do it in conf file? use the device command. For instance if you want to disable GPU 1 you use the command: "device": "0,2,3", |
|
|
|
I'm waiting for Wolf0miner.  |
|
|
|
R9 280X hynix rawintensity 6144 Worksize 256 tc 8192 1140/1600 gpu-threads 2 amd 14.6rc2 280 kH/s ..I need better settings  R9 280X hynix rawintensity 6144 Worksize 256 tc 8192 1000/1500 gpu-threads 2 amd 14.6 312 kH/s |
|
|
|
Can someone post comparison to X11 in terms of power consumption please? Is it higher? Is it lower?
With x11 you may not be too successful with undervolting your gpus much. Since neoscrypt is a scrypt algo, you can undervolt substantially. When I leave my cards at x11 settings (full voltage) and then switch to neoscrypt, it pulls 13% more from the wall. However, if I undervolt my cards to a scrypt setting it is only about 7% more. Of course this depends on which gpus you have. I may be able to work my cards down even more with neoscrypt but I am content here. |
|
|
|
|
I've found tons of Phoenixcoin with his .cl and the cgminer-3.7.7.bNeoscrypt. As for trust, well, he's given this kernel to us. What have you given us other than FUD?
|
|
|
|
I can solo mine with the Wolf0 neoscrypt.cl with cgminer-3.7.7.bNeoscrypt. I cannot with any sgminer. I get the same error message.
What error message are you getting? I solo-mine a lot of things with a lot of sgminer variants. I didn't think my post was unclear. I said the same error message. 3.7.7.b isn't his.  trolololol.. Tyvm for confirming my findings. Plz post a screenie or better yet the log file. I don't follow you. Of course he didn't write cgminer 3.7.7bNeoscrypt. But he did write the .cl which works fine with it. And it solo mines. So what is your point exactly? |
|
|
|
I can solo mine with the Wolf0 neoscrypt.cl with cgminer-3.7.7.bNeoscrypt. I cannot with any sgminer. I get the same error message.
What error message are you getting? I solo-mine a lot of things with a lot of sgminer variants. I didn't think my post was unclear. I said the same error message. |
|
|
|
|
I can solo mine with the Wolf0 neoscrypt.cl with cgminer-3.7.7.bNeoscrypt. I cannot with any sgminer. I get the same error message.
|
|
|
|
No, PM me, I've got 2.8965 TRILLION BTCRY |
|
|
|
|
Wolf0, you are the man!
my 14.6 and 14.7 rigs are flying!
|
|
|
|
How much electricity needed for neoscrypt compared to x11,x13,x15.?
My rigs are using about 13% more with neoscrypt over x11. |
|
|
|
What version AMD drivers are installed? 14.9?
Yeah 14.9. I just downgraded one rig to 14.7 RC3 on as suggested, and I do see an initial 5 kHash improvement. Right now running about 150-151 khash with 1040/1500 -w 48 -I 13 -g 1. Seems raising the core clock for me does nothing more and in some cases it even reduced the khash a bit. I am still fiddling with different settings, so holding out hope for a bit more.... I have four rigs, one with 14.6rc, 14.7rc, and the other 2 with 14.7rc3. By far, the 14.6rc leads in hashrate with hd7970s over hd7970s in the 14.7rc and the 14.7rc3 with 280xs. 1000/1500 -w 48 -I 13 -g2. |
|
|
|
Tbh, I'm finding it quite peculiar that my 140 khash noob's config is the best we have for 3.7.7b. And how the only alternative is Wolf0's blacklisted site with it's nsfw .pngs and promises of higher hashrates (on a client that can't or won't solo mine), seeminly designed to lure people to said site. wolf0s miner works well, iam useing his public release version. there is also an updated cgminer as well at 3.7.8 which has speeds similar to wolf0s. I am using Wolf modified neoscrypt140909.Cl file on my installs, so essentially it is the same as 3.7.8. I do have one rig running actually running the 3.7.9 and can confirm that my speeds are essentially the same. This is between rigs of both 7970 and 280x cards, which again are basically the same, but the road block for me seems to kick in at around 140 khash -145 khash. I have tried messing with clocks and settings, but to go from core clocks of ~1040 to 1150 for only a 1-2 khash improvement does not seem to be worth it considering my power draw from the wall goes up as well. Just when I read people getting 160-175 khash out of similar setups using similar settings makes me think I am overlooking something simple, thus why I am asking for input. Edit: I should add that all my GPU are using Hynix memory as those appear to be the cards capable of the 175 khash people are reporting. What version AMD drivers are installed? 14.9? |
|
|
|
i dont get how you guys are getting such high speeds. i have tried all the settings on my 280x's and they barley do 120khs. tried with both new sgminer and latest cgminer. I think the secret is to not have AMD 14.9 installed. I am using 14.6. This isn't the first algorithm I've seen to perform poorly with 14.9. p.s. see my comments here https://bitcointalk.org/index.php?topic=632503.msg9412232#msg9412232intresting, i will give it a go and see what results i gain, as its the same across my 2 rigs, 4 280x's do about 122khs and my 7950's do around 117khs. so i will change drivers and post the results. *Edit just noticed you cant download 14.6 drivers anymore :-/ only 14.4 and lower. also do you use a TC setting? No TC setting. But of course the .bin file shows that it is using 8192. I keep all my old AMD bundles, so going to 14.6 was easy. Big file though 300+MB. |
|
|
|
i dont get how you guys are getting such high speeds. i have tried all the settings on my 280x's and they barley do 120khs. tried with both new sgminer and latest cgminer. I think the secret is to not have AMD 14.9 installed. I am using 14.6. This isn't the first algorithm I've seen to perform poorly with 14.9. p.s. see my comments here https://bitcointalk.org/index.php?topic=632503.msg9412232#msg9412232 |
|
|
|
I am sorry, can't seem to find an answer anywhere. Whats the power consumption in neoscrypt compared to other algos? Like scrypt and x11 ie? Thanks for the answers  At one of my rigs X11 consumes 720w, neoscrypt is at 810-820w so it's 10-15% more. I can second that conclusion. |
|
|
|
|
0.9.2.6 will not advance past this last 0 hour. Stuck at 741010.
|
|
|
|
|
Show Posts
