|
A bit offtopic question, but I don't know where to ask. Can I send BTC to a native SegWit bc1 address using Armory 0.96.5 + Core 0.19.1? And just for further info: Is any bitcoin core client able to send to a bc1 address?
Thanks!
|
|
|
|
|
Is there a way to speed up the Scanning part when importing a new wallet? Is the CPU the bottleneck or it's something else?
|
|
|
|
just got mine in, just started testing but have 3 newpacs running @ 350 MHz
Is 3 newpacs the maximum for this hub? If not then what's the maximum? |
|
|
|
|
15x Halong DragonMint T1 16.5 TH/s w/ Myrig MP288 PSU - $500 each + shipping from Asia
Hello. A friend of mine asked me to post this ad for him. He is located in Asia and he is selling 15x DragonMints T1. Shipping will be done from an Asian country I am open for any kind of inquiries.
|
|
|
|
Are you going to do anything SHA or stick with other algos?
-Dave
Regarding SHA maybe, but not in the near future. I will be available anytime for a group buy! mate, your sig.. move away from the past and move on. You are correct. Edited my sig. Thank you! |
|
|
|
Are you going to do anything SHA or stick with other algos?
-Dave
Regarding SHA maybe, but not in the near future. I will be available anytime for a group buy! |
|
|
|
Missed us?
  |
|
|
|
I am having the exact same problems with Halong software.
How do you install Innosilicon software on B52?
Just like you would install a regular firmware. |
|
|
|
|
How do you restore miner settings to default without the credentials?
|
|
|
|
I can confirm, not that it matters. The S11 Firmware from Innosilicon works on the DragonMint B52 and appears to provide a noticeable increase in the poolside hashrate. It also doesn't get stuck in auto-tune so you can crank up to performance mode if you want.
Wasn't the issue resolved in the Halong firmware? |
|
|
|
this thread has April and May links not sure about the oem (march firmware).
9th April is the earliest that I could find. |
|
|
|
For T1, if hash PCB is unstable, please try, original firmware it came with, then some from late March, then April 28th version and newest ones. each of these version may have a good compatibility if you have some strange case of stability or not hashing PCB. To speed up the exchange be, to email support@myrig.com with Myrig or Halong original order number and use same original shipping address as place of warranty item delivery location, and include serial number of the unit along with picture of the miner or damaged item.
I have found for my five try low speed and middle speed on multiple firmwares it has so far always (fingers crossed) work on the one t1 with a weak board.
Where can I find the original firmware and late March? |
|
|
|
Can somebody tell me with the latest firmware update what the power consumption is on all 3 modes?
Also, is there any reason to NOT run on performance mode if I'm paying a flat rate in a datacenter?
It depends on whether you're using 120 or 220/240V and what efficiency your PSU is. They're usually around 1200,1540,1640 here for 14, 16, 16.4TH at 240V with 94% titanium PSUs. I would not run them in performance mode unless 1. you had a lot of cooling (ambient at or below 20C), 2. your PSUs were rated above 1750W and 3. your electricity costs were extra low and efficiency did not matter; the Myrig PSUs are rated at 1680 which is cutting it too fine. Good information! Thank you. |
|
|
|
Hello. What should be the performance setting after applying the mentioned firmware? Is there an update for this? I got 2 miners that have 1 dead PCB. After many restarts one miner revived 1 PCB, but only for a couple of days. Board seems to light when powering the miner on, dies afterwards. Changing the power/interface cables/slots has any impact? |
|
|
|
Great, thanks for the feedback  Thank you too for the code! |
|
|
|
|
I would like to buy a spare PSU. What are the specs of the PSU and where can I buy one? Halong should sell separate PSUs...
|
|
|
|
Hey Inno_ASIC when will you release the next batch of S11 miner?
Still waiting for a reply Inno_ASIC |
|
|
|
|
Hey Inno_ASIC when will you release the next batch of S11 miner?
|
|
|
|
I have an issue after trying the latest firmware. After ~20 secs after the miner starts the PCBs are turning off one by one and the nothing happens. Any ideas? The same happens with the 15.04 firmware. Works fine with the original firmware.
Thank you!Edit: Apparently I just had to wait  |
|
|
|
|
Show Posts
