ethOS - Ethereum Mining Platform

[kjs]

New version is out - 1.31 from April 4th

Someone checked if voltage can go below 0.9v with this one? I see they improved their voltage control tool.

Yes, you can set voltage to less than 950 mV by setting

Code:

safevolt disabled

within your config file.

[sadkosius]

Hey guys. I was wondering whether someone can explain to me about the custom panel name. I can't figure it out. How to set it up in a config file and what if someone else has or will take the same custom panel name? Thanks.

[Xexen4]

after setting  vol RIGID 900 900 xxx parameter pwr parameter did not working. my cards powertune is 5 now. i use pwr RIDIG 2 2 2 with vol parameter. i have no idea about power consumption now.
why pwr params disabled with using vol ?

[greyday]

after setting  vol RIGID 900 900 xxx parameter pwr parameter did not working. my cards powertune is 5 now. i use pwr RIDIG 2 2 2 with vol parameter. i have no idea about power consumption now.
why pwr params disabled with using vol ?

If you updated to 1.3.1, it should directly report wattage now.

[Xexen4]

after setting  vol RIGID 900 900 xxx parameter pwr parameter did not working. my cards powertune is 5 now. i use pwr RIDIG 2 2 2 with vol parameter. i have no idea about power consumption now.
why pwr params disabled with using vol ?

If you updated to 1.3.1, it should directly report wattage now.

yea i upgrade ethos to 1.3.1 but on ati gpus watt consumption not shown on panel. with nvidia gpus i can see watt consumption per gpu. if i am not wrong, pwr parameter works with 1-7 values on amd gpus as powertune settings.

[hagbase]

You're wrong and it also depends on how heavy your VBios is modded.

# KNOWN GOOD SAMPLE AMDGPU (RX 400/500) GLOBAL CONFIG
# ------------------------------------------------------
# globalcore 1180
# globalmem 2000
# ------------------------------------------------------
#
# NOTE:   AS of ethOS 1.3.1, OPTIONAL "pwr"/"globalpowertune" adjusts AMDGPU watts, and OPTIONAL dpm adjusts AMDGPU dpm state.
#       Set lower for lower power usage, set higher if overclocking. Limiting power this way will negatively impact hashrate.
#       It is advised to use voltage adjustment to achieve low power draw while maintaining high hashrate.
#       Default DPM is 5
#       "dpm"/"globaldpm" is DPM state range 0-7 (OPTIONAL). Set lower may lower power usage, set higher if overclocking.
#       "vlt" has a safe voltage range of 950 (low) to stock +150mv.
#       To enable UNSAFE/DANGEROUS voltage adjustments, set "safevolt disabled".
#
# ------------------------------------------------------
# globalpowertune 130
# globaldpm 5
# safevolt enabled
# ------------------------------------------------------
#
# SAMPLE PER-RIG CONFIG FOR AMDGPU (for a 6-gpu rig)
# ------------------------------------------------------
# cor c94e13 1180 1180 1180 1180 1180 1180
# mem c94e13 2150 2150 2150 2150 2150 2150
# pwr c94e13 130 130 130 130 130 130
# dpm c94e13 5 5 5 5 5 5
# vlt c94e13 950 950 950 950 950 950
# ------------------------------------------------------
#
# ADVANCED AMDGPU (RX 400/500)  Overclocking notes:
# NOTE: vddci is adjustable between values of 700 and 1000 (mv)
# WARNING: Do not adjust without understanding what VDDCI does as you may damage your hardware!
#
# VDDCI CONFIG EXAMPLE (PER-RIG):
# ------------------------------------------------------
# vddci c94e13 900 900 900 900 990 900 900
# ------------------------------------------------------

[greyday]

after setting  vol RIGID 900 900 xxx parameter pwr parameter did not working. my cards powertune is 5 now. i use pwr RIDIG 2 2 2 with vol parameter. i have no idea about power consumption now.
why pwr params disabled with using vol ?

If you updated to 1.3.1, it should directly report wattage now.

yea i upgrade ethos to 1.3.1 but on ati gpus watt consumption not shown on panel. with nvidia gpus i can see watt consumption per gpu. if i am not wrong, pwr parameter works with 1-7 values on amd gpus as powertune settings.

Make sure your upgrade worked and your panel shows 1.3.1 for the rig; mine reports AMD wattage for 6x580...

[Xexen4]

after using pwr parameter rig was lowered hashes and crashed. i did not find stable config parameters yet. i will re-update my vbioses with new one.

[greyday]

after using pwr parameter rig was lowered hashes and crashed. i did not find stable config parameters yet. i will re-update my vbioses with new one.

Yeah, I abandoned the globalpowertune setting for now. Still getting 4h/s increase per card and a decent voltage drop since the update just using my previous settings. Will play with them when I have time, but I'm happy enough with my rig at the moment.

[Zeruel]

Is there a miner in ethos 1.3.1 to mine CN Heavy?

If there isn't, please include it in the next update.

I've tried compile miners on my own and even try sgminer-gm 5.5.6 with no luck.

[greyday]

Is there a miner in ethos 1.3.1 to mine CN Heavy?

If there isn't, please include it in the next update.

I've tried compile miners on my own and even try sgminer-gm 5.5.6 with no luck.

If any of the miners in their list have updates that support it, try sudo update-miners (or do your specific one). You can also install miners that aren't on their list. It CAN break ethos, fair warning, but it likely won't (still, I tend to do a full drive image backup before I install anything on active rigs).

[coinmancan]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

[greyday]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

If that was the only rig reporting and it was offline for a little bit, the system probably just changed your panel "name". Confirm the address by typing helpme into your rig.

[coinmancan]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

If that was the only rig reporting and it was offline for a little bit, the system probably just changed your panel "name". Confirm the address by typing helpme into your rig.

Thanks for your quick response.  The rig boots and hashes fine. The name is the same.  The problem is that the Chromium browser window is all black and then a Page Unresponsive alert window pops up.  I've rebooted the machine numerous times.  Same problem.  "helpme" works fine as well as the "browser" command, however the Chromium window is blank and unresponsive. I've read this thread and searched the internet and haven't seen any answers.

[greyday]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

If that was the only rig reporting and it was offline for a little bit, the system probably just changed your panel "name". Confirm the address by typing helpme into your rig.

Thanks for your quick response.  The rig boots and hashes fine. The name is the same.  The problem is that the Chromium browser window is all black and then a Page Unresponsive alert window pops up.  I've rebooted the machine numerous times.  Same problem.  "helpme" works fine as well as the "browser" command, however the Chromium window is blank and unresponsive. I've read this thread and searched the internet and haven't seen any answers.

Test it in another browser? Or email them; the OS isn't technically supported but I've found the panel tends to be (I usually get a response within a day or so).

You can also try testing it in the iOS/android app, or post it here and one of us can try it...

[ethosdash]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

If that was the only rig reporting and it was offline for a little bit, the system probably just changed your panel "name". Confirm the address by typing helpme into your rig.

just type in 'browser' in command line to launch Chromium

[ethosdash]

Hello.  I just updated my rig to 1.3.1 and clicking on the menu shortcuts for ethOS Stats Panel and ethOS Knowledgebase bring up a blank Chromium screen.  After a little bit, an alert pops up that says the page is unresponsive, but that is blacked out as well.  I see no other ways to open Chromium and this bug was not there before the update.  Next steps?

If that was the only rig reporting and it was offline for a little bit, the system probably just changed your panel "name". Confirm the address by typing helpme into your rig.

just type in 'browser' in command line to launch Chromium

alternatively, you can use this website for stats and profit calculations, at https://ethosdash.com it's using API from ethosdidtro server, and it woks a bit faster.

[coinmancan]

I appreciate everyone's chiming in. At the same time no one's taken the time to (carefully) read what I've written and we're really going down the wrong path here.  As written previously:

The rig was updated to 1.3.1.
The rig boots and hashes fine.
The Chromium window is unresponsive. and blank/black.
The "browser" command works.
The menu shortcut works.
After a while a notification pops up that says "Page unresponsive". This is also blank/black.

The info posted is helpful, just not applicable. I'm re-writing this so that if someone else searches they can see that they were not the only person with the problem.  Also re-writing for the sake of showing that we can help each other better when we read what each other has written. This happens a lot nowdays, people skim emails and messages and communication suffers.

To solve the issue I've redownloaded ethOS and will reinstall as I need to use the internet on the machine and the Chromium program, as mentioned above, is not working.

[ethosdash]

I appreciate everyone's chiming in. At the same time no one's taken the time to (carefully) read what I've written and we're really going down the wrong path here.  As written previously:

The rig was updated to 1.3.1.
The rig boots and hashes fine.
The Chromium window is unresponsive. and blank/black.
The "browser" command works.
The menu shortcut works.
After a while a notification pops up that says "Page unresponsive". This is also blank/black.

The info posted is helpful, just not applicable. I'm re-writing this so that if someone else searches they can see that they were not the only person with the problem.  Also re-writing for the sake of showing that we can help each other better when we read what each other has written. This happens a lot nowdays, people skim emails and messages and communication suffers.

To solve the issue I've redownloaded ethOS and will reinstall as I need to use the internet on the machine and the Chromium program, as mentioned above, is not working.

hi coinman, i'm sorry to hear of your frustration with chromium, but as long as your rig and miner are working, perhaps it's not an ethOS issue as such, but rather Ubuntu or Chromium itself. I had an instance were home page -  panelid.ethosdistro.com wasn't responding and I was getting same message, but other web content was displayed with no issues. Good luck with it anyways. I hope my message hasn't cause any suffer to the communication channel))

[Maxxbill]

BIP-32 : Ethos
BIP-32 describes what Hierarchical Deterministic wallets (HD wallets) are and how they operate. An HD wallet is a system for deriving seemingly infinite private/public key pairs from

https://support.ethos.io/support/solutions/articles/35000072135-bip-32