ASICMINER Auction: 50 Block Erupter Blades CHECK OP FOR PAYMENT

[Omen1855]

It was pure hell today, had to pick up from DHL myself. Total traffic disaster. 2 ATX PSUs I assumed to work were dead (thankfully I could sacrifice a third). Total heart-attack after boot failure (fans went on for one sec and then system shut down again). Tried again and now it's running at slightly less than 13 GH/s without overclocking.

It's pretty easy to assemble and easy enough to configure. Using a custom PSU is quite stressful, even though it works like a charm.

[michelet]

So happy!!

(this is a temporary case )

[wsoei]

So happy!!

(this is a temporary case )


http://w ww.easy.pc.it/34b.jpg

I'm totally Jelly!!!!  Grats on 40+ Gh/s

[Omen1855]

I don't even dare to show my current setup
Congrats!

[lan787]

did anyone check the power consumption?
my old fan controller reports 120 and 150 wats in low and high clocks respectievly.
I don't trust it much though

[Caesium]

I have a plug in power meter so can tell you tomorrow what mine do

damn bank holiday!

[desired_username]

Got mine set up and running.

It's on air atm, but I'm expecting to receive the oil tank, and some bits and pieces in 2 weeks

Also, I have one question, I'm on slush atm, and there's a suggested difficulty option, which was set to 8 by the pool.
Should I change this?

[dserrano5]

(this is a temporary case )

We all know what that means .

[lightbox]

Hmm my stratum proxy is spewing out all kinds of rejects (and my efficiency is hovering around 30-50%) in the blade UI..

REJECTED: (-2, u;lowdifficulty', None)

im using
./mining_proxy -o stratum.btcguild.com -p 3333 -cu myusername

and on the blades:

serveraddress: 192.168.1.200,192.168.1.200    (ip of server running stratum proxy)
ports:8332,8332


thoughts?

[pixel75]

(this is a temporary case )

We all know what that means .

probably that temporary = forever???

[Noitev]

can someone with a woorking miner (or knows how they work) PLEASE message me on irc [freenode] (or on here...), tips might be involved...

[rammy2k2]

anyone has any idea when friedcat will make next auction for these blades ? I pm-ed him but no reply ... i bet he's pretty busy tho

[pixel75]

can someone with a woorking miner (or knows how they work) PLEASE message me on irc [freenode] (or on here...), tips might be involved...

quote here your questions. someone like me will be glad to help you.

[lan787]

This is my "temporary". I think one board can be mounted into old desktop case.

Also, I have one question, I'm on slush atm, and there's a suggested difficulty option, which was set to 8 by the pool.
Should I change this?

I run this difficulty too. With this setting you have 100 packets and 10KB per minute. The variance per round is pretty large for me: 0.026-0.036.
So if you need more stable income you should decrease difficulty. If you have bandwidth issues or limited tariff plan you may wish to increase.

[lightbox]

Hmm my stratum proxy is spewing out all kinds of rejects (and my efficiency is hovering around 30-50%) in the blade UI..

REJECTED: (-2, u;lowdifficulty', None)

im using
./mining_proxy -o stratum.btcguild.com -p 3333 -cu myusername

and on the blades:

serveraddress: 192.168.1.200,192.168.1.200    (ip of server running stratum proxy)
ports:8332,8332


thoughts?

fixed -- need to use a different worker for each blade, cannot specify "-cu" and let them share a single worker.

[desired_username]

I run this difficulty too. With this setting you have 100 packets and 10KB per minute. The variance per round is pretty large for me: 0.026-0.036.
So if you need more stable income you should decrease difficulty. If you have bandwidth issues or limited tariff plan you may wish to increase.

thanks for the answer


my performance data (The values are the same (+-100) in the web interface)

[willphase]

congrats on you all getting your blades!  I'm sorta jealous that I missed winning by 1BTC...   It would have been nice to have a new mining toy to play with!

Will

[rammy2k2]

anyone has any idea when friedcat will make next auction for these blades ? I pm-ed him but no reply ... i bet he's pretty busy tho

[lan787]

I believe he has no idea too

[Gomeler]

Received mine and got it up and running use the stratum proxy pointed at btcguild. Has anyone bothered to try running any SHA256 alt-coins with this thing? I briefly tried to get TRC running with p2pool and failed miserably. p2pool was complaining about the blade returning hash values greater than expected.