greenfailure
Member
Offline
Activity: 145
Merit: 11
|
|
February 02, 2018, 04:37:06 PM |
|
I am new to this whole thing about antminer. This is my screenshoot of my antminer A3. It is still safe that the chip temps reach up to 90 C? Also what software can we use to monitor our A3 from outside computer ? 90 is a bit high, you may want to manually set your fan. Start at 95% and lower until you feel comfortable (also note that these machines are buggy and sometimes a simple power cycle will have it running a little cooler). I have mine running in a cold (50-55F) basement with the fan set to 90 and the clock set to 631 and the hottest chips are running just under 80C. Which is still slightly uncomfortable for me, but since it ran stock at 84C so I'm cool with it. 90 is worrying, though, and I'd try upping your fan speed. How to manually adjusting the fan ? under the main miner settings tab click the 'manual fan' control box, and set the % you want it to run at. I run all my Bitmain ASICs at 100%, never have had issues.
|
Owner/Operator of LARGEST Greater Toronto Area mining operation.
BUY BITCOIN
|
|
|
Tekno2020
Member
Offline
Activity: 262
Merit: 11
<<<-----( )----->>>
|
|
February 02, 2018, 04:44:28 PM |
|
Guys can we stop the miner FUD?
Global hashrate is around 8P right now, which means there were roughly 10K A3's released in batch one. Block time is still around 20 min's, this has been decreasing and will hit 10 min soon. Right now profitability is near 1300SC/day which should be near 2600SC/day when the block time corrects in a few days time.
Until batch 2, 2600SC/day should be stable. If batch 2 is also near 10K units this will halve to 1300SC/day which is still $30 ish per day at current price. If batch 2 is 20K units then we should be seeing around 650SC/day or $15 ish/day at current price.
So the only way batch 2 stands to not be profitable is if there is a major crash in sia price or more than 20K units are shipped. Is it the $600/day that people were getting on day one, no. But it will still likely be one of Bitmain's most profitable miners until batch 3.
I wish i could trust your calcs i would buy two more units. but idk Don't trust anybodys calcs.... you have to do your own. The devs may have a better idea about the structure of the difficulty algo and where the difficulty where level off.... but you have to do your own calcs. There are plenty of unknowns, like Bitmain's batch sizes. The folks at Obelisk disclosed their batch sizes which makes it easier to estimate difficulty and profitability, but look what happened to them.
|
~The Annointed One~ btc: 31pDmi6PDdHFUT51MTzJNYacxYMZp2bi58 ltc: MGnitxNo2qZNgb2biahDguxMZuCbGPQQ84
|
|
|
|
VoskCoin (OP)
|
|
February 02, 2018, 05:14:06 PM |
|
@VoskCoin
What freq do you run your A3? What are your temps?
freq 644 and I do not recommend overclocking in full disclosure etc whatever / full dash https://imgur.com/sN20uA7/ miner pulls in outside air currently around 40 f
|
|
|
|
nsummy
|
|
February 02, 2018, 05:29:41 PM |
|
I just got my A3 today....so what's the best pool for SC right now?
I like luxor. They pay out regularly and have a good interface, plus they are large but not the dominant and they donate back to the SIA devs. sia.luxor.tech I would recommend anyone who is thinking about mining at Luxor read this first: https://medium.com/@nitronick600/message-to-nebulous-labs-7c42df1f86d5 I mined there for a few days, thinking I was doing my civic duty to spread the hashrate and support the devs. Then my eyes were opened.
|
|
|
|
nsummy
|
|
February 02, 2018, 05:34:04 PM |
|
Guys can we stop the miner FUD?
Global hashrate is around 8P right now, which means there were roughly 10K A3's released in batch one. Block time is still around 20 min's, this has been decreasing and will hit 10 min soon. Right now profitability is near 1300SC/day which should be near 2600SC/day when the block time corrects in a few days time.
Until batch 2, 2600SC/day should be stable. If batch 2 is also near 10K units this will halve to 1300SC/day which is still $30 ish per day at current price. If batch 2 is 20K units then we should be seeing around 650SC/day or $15 ish/day at current price.
So the only way batch 2 stands to not be profitable is if there is a major crash in sia price or more than 20K units are shipped. Is it the $600/day that people were getting on day one, no. But it will still likely be one of Bitmain's most profitable miners until batch 3.
The only people spreading fud are the ones who didn't get in on the initial order and/or are too broke to buy one for 1000 bucks. I don't think anyone is going to get rich buying a 2nd batch A3 but they will most likely make handsome profit. It is certainly no worse than buying a 1080ti right now.
|
|
|
|
Hendrikclaasen
Newbie
Offline
Activity: 47
Merit: 0
|
|
February 02, 2018, 05:40:03 PM |
|
Thx - think it is winter where you are...... we are in mid summer and with the default settings my temps are in the 88-92 range.... think I will not try the overclocking....
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 02, 2018, 11:54:15 PM |
|
I just got my A3 today....so what's the best pool for SC right now?
I like luxor. They pay out regularly and have a good interface, plus they are large but not the dominant and they donate back to the SIA devs. sia.luxor.tech I would recommend anyone who is thinking about mining at Luxor read this first: https://medium.com/@nitronick600/message-to-nebulous-labs-7c42df1f86d5 I mined there for a few days, thinking I was doing my civic duty to spread the hashrate and support the devs. Then my eyes were opened. I read that before I even got my miner. I see no problem with it, and in fact support many aspects of it.
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 02, 2018, 11:57:16 PM |
|
@VoskCoin
What freq do you run your A3? What are your temps?
freq 644 and I do not recommend overclocking in full disclosure etc whatever / full dash https://imgur.com/sN20uA7/ miner pulls in outside air currently around 40 f I'm running 631 @ 88% fans currently (100 makes an annoying vibration in my floor). Running fine, temps in the mid to high 70s (pulling cold basement air), though I am still baffled by the whole "if you reboot, your temperatures change by 5-10 degrees" thing.
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 03, 2018, 12:52:36 AM |
|
anyone using Luxor ? they use PPLNS now. I still get 0 SC on my balance since the last payout ( approx 2 hours ago). Is there a way to know what our current balance is ?
Just noticed that. Payout still seems about the same so far for me, but now I have to do some income comparisons again...
|
|
|
|
VoskCoin (OP)
|
|
February 03, 2018, 12:54:24 AM |
|
@VoskCoin
What freq do you run your A3? What are your temps?
freq 644 and I do not recommend overclocking in full disclosure etc whatever / full dash https://imgur.com/sN20uA7/ miner pulls in outside air currently around 40 f I'm running 631 @ 88% fans currently (100 makes an annoying vibration in my floor). Running fine, temps in the mid to high 70s (pulling cold basement air), though I am still baffled by the whole "if you reboot, your temperatures change by 5-10 degrees" thing. theyre 5-10 higher or lower for you?
|
|
|
|
dlezama
Member
Offline
Activity: 140
Merit: 17
|
|
February 03, 2018, 01:02:03 AM |
|
anyone using Luxor ? they use PPLNS now. I still get 0 SC on my balance since the last payout ( approx 2 hours ago). Is there a way to know what our current balance is ?
Just noticed that. Payout still seems about the same so far for me, but now I have to do some income comparisons again... They switched to PPLNS because they have some technical problem causing less than 50% luck as of now (here: https://siastats.info/mining_pools.html). So they were losing money with PPS. Now you will pay for this instead, getting half of what you should. I wouldn't use a PPLNS pool with 47% luck if I were you.
|
|
|
|
tavogl
Newbie
Offline
Activity: 25
Merit: 0
|
|
February 03, 2018, 01:10:27 AM |
|
how much are they making a day$? in the last 2 days? thanks! got someone selling one for 3k, is it worth it?
|
|
|
|
shaninium
|
|
February 03, 2018, 01:19:09 AM |
|
@VoskCoin
What freq do you run your A3? What are your temps?
freq 644 and I do not recommend overclocking in full disclosure etc whatever / full dash https://imgur.com/sN20uA7/ miner pulls in outside air currently around 40 f I'm running 631 @ 88% fans currently (100 makes an annoying vibration in my floor). Running fine, temps in the mid to high 70s (pulling cold basement air), though I am still baffled by the whole "if you reboot, your temperatures change by 5-10 degrees" thing. theyre 5-10 higher or lower for you? They would be lower because rebooting them cools them down cause mining stops then fans sync. Wont last though depending on ambient temp
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 03, 2018, 03:26:30 AM |
|
I'm running 631 @ 88% fans currently (100 makes an annoying vibration in my floor). Running fine, temps in the mid to high 70s (pulling cold basement air), though I am still baffled by the whole "if you reboot, your temperatures change by 5-10 degrees" thing.
theyre 5-10 higher or lower for you? They would be lower because rebooting them cools them down cause mining stops then fans sync. Wont last though depending on ambient temp Nope, they're both. I'm talking about a bug in the A3 itself (that others have reported too). If I make a change, as it is resetting it will either go up 5-10 from the previous running or down, but whichever it is it runs consistently at. So for example, my current temps are 79-75-81. The last time I changed wallets, the temps were all in the mid 80s, so I reset again and they are back down. It's been a pretty common thing based on posts on this board (though I don't know if it is universal or not), so if your A3 is running hot, you might be able to bring it down a bit just by hitting "save and apply".
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 03, 2018, 03:34:16 AM |
|
anyone using Luxor ? they use PPLNS now. I still get 0 SC on my balance since the last payout ( approx 2 hours ago). Is there a way to know what our current balance is ?
Just noticed that. Payout still seems about the same so far for me, but now I have to do some income comparisons again... They switched to PPLNS because they have some technical problem causing less than 50% luck as of now (here: https://siastats.info/mining_pools.html). So they were losing money with PPS. Now you will pay for this instead, getting half of what you should. I wouldn't use a PPLNS pool with 47% luck if I were you. THANK YOU for this. Swapping over to Siamining until this is sorted!
|
|
|
|
nsummy
|
|
February 03, 2018, 05:26:08 AM |
|
I just got my A3 today....so what's the best pool for SC right now?
I like luxor. They pay out regularly and have a good interface, plus they are large but not the dominant and they donate back to the SIA devs. sia.luxor.tech I would recommend anyone who is thinking about mining at Luxor read this first: https://medium.com/@nitronick600/message-to-nebulous-labs-7c42df1f86d5 I mined there for a few days, thinking I was doing my civic duty to spread the hashrate and support the devs. Then my eyes were opened. I read that before I even got my miner. I see no problem with it, and in fact support many aspects of it. So you support the pool that wants to render the miner you just spent $2500 on useless? That makes no sense.
|
|
|
|
greyday
Member
Offline
Activity: 434
Merit: 52
|
|
February 03, 2018, 05:29:18 AM |
|
I just got my A3 today....so what's the best pool for SC right now?
I like luxor. They pay out regularly and have a good interface, plus they are large but not the dominant and they donate back to the SIA devs. sia.luxor.tech I would recommend anyone who is thinking about mining at Luxor read this first: https://medium.com/@nitronick600/message-to-nebulous-labs-7c42df1f86d5 I mined there for a few days, thinking I was doing my civic duty to spread the hashrate and support the devs. Then my eyes were opened. I read that before I even got my miner. I see no problem with it, and in fact support many aspects of it. So you support the pool that wants to render the miner you just spent $2500 on useless? That makes no sense. No, I do not. I said I support many aspects of it. That doesn't mean all of it.
|
|
|
|
VoskCoin (OP)
|
|
February 03, 2018, 01:48:48 PM |
|
I'm running 631 @ 88% fans currently (100 makes an annoying vibration in my floor). Running fine, temps in the mid to high 70s (pulling cold basement air), though I am still baffled by the whole "if you reboot, your temperatures change by 5-10 degrees" thing.
theyre 5-10 higher or lower for you? They would be lower because rebooting them cools them down cause mining stops then fans sync. Wont last though depending on ambient temp Nope, they're both. I'm talking about a bug in the A3 itself (that others have reported too). If I make a change, as it is resetting it will either go up 5-10 from the previous running or down, but whichever it is it runs consistently at. So for example, my current temps are 79-75-81. The last time I changed wallets, the temps were all in the mid 80s, so I reset again and they are back down. It's been a pretty common thing based on posts on this board (though I don't know if it is universal or not), so if your A3 is running hot, you might be able to bring it down a bit just by hitting "save and apply". I dont have good data to support this but I've basically noticed the same thing and found it really odd. . . couple restarts and monitoring temps for just a short period seemed to yield "yeah it looks good now.." lol
|
|
|
|
CryptoDemonElite
Jr. Member
Offline
Activity: 238
Merit: 7
|
|
February 03, 2018, 02:12:44 PM |
|
I really want to get in this mining business, but don't know where to start. Any help?
|
|
|
|
|