vcon
Newbie
Offline
Activity: 1
Merit: 0
|
|
October 31, 2018, 01:04:27 AM |
|
Has anyone found a way to enable SSH on the Z1+?
|
|
|
|
Tarlatata
Jr. Member
Offline
Activity: 102
Merit: 2
|
|
October 31, 2018, 01:36:25 AM |
|
Nice catch. Tomax is looking at avaibility/specs for me right now.
|
|
|
|
alex.asic
Newbie
Offline
Activity: 49
Merit: 0
|
|
October 31, 2018, 07:42:47 AM |
|
Thanks for that. Not worth buying unless almost free electricity it seems.
|
|
|
|
streenip
Jr. Member
Offline
Activity: 39
Merit: 1
|
|
October 31, 2018, 05:31:50 PM |
|
It’s 1:30 am in China, any improvement on the income?
|
|
|
|
xs.over
|
|
October 31, 2018, 05:48:54 PM |
|
It’s 1:30 am in China, any improvement on the income?
Remember a simple thing: nowadays mainly only miming hardware manufacturers and hardware resellers earn money in crypto mining sphere.
|
|
|
|
esol
Jr. Member
Offline
Activity: 41
Merit: 6
|
|
October 31, 2018, 07:16:42 PM |
|
hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"
of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...
any idea how to set by software to avoid FAN speed check?
any other idea? thanks! /E
|
|
|
|
deneme12
Newbie
Offline
Activity: 8
Merit: 0
|
|
November 01, 2018, 02:10:38 AM |
|
It’s 1:30 am in China, any improvement on the income?
Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words...
|
|
|
|
topoolscom
Newbie
Offline
Activity: 24
Merit: 0
topools.com
|
|
November 01, 2018, 03:47:52 AM |
|
It’s 1:30 am in China, any improvement on the income?
Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words... I think dayun.company is not Z1 official website.
|
|
|
|
alex.asic
Newbie
Offline
Activity: 49
Merit: 0
|
|
November 01, 2018, 07:07:03 AM |
|
Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher? Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement. Thanks.
|
|
|
|
streenip
Jr. Member
Offline
Activity: 39
Merit: 1
|
|
November 01, 2018, 07:48:30 AM |
|
Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher? Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement. Thanks.
Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.
|
|
|
|
alex.asic
Newbie
Offline
Activity: 49
Merit: 0
|
|
November 01, 2018, 08:15:56 AM |
|
Thank you i had forgotten about that write up. ill set the temp limit and see how we go. Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher? Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement. Thanks.
Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.
|
|
|
|
Yezzzuurrr
Newbie
Offline
Activity: 37
Merit: 0
|
|
November 01, 2018, 08:55:42 AM |
|
Thank you i had forgotten about that write up. ill set the temp limit and see how we go. Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher? Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement. Thanks.
Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine. On the auto stop which settings do you use for the fans? lowerfanspeed in and lowerfanspeed out
|
|
|
|
Yezzzuurrr
Newbie
Offline
Activity: 37
Merit: 0
|
|
November 01, 2018, 09:06:29 AM |
|
It’s 1:30 am in China, any improvement on the income?
Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words... i think http://www.dayunmining.com/ is official site?
|
|
|
|
alex.asic
Newbie
Offline
Activity: 49
Merit: 0
|
|
November 01, 2018, 09:08:07 AM Last edit: November 01, 2018, 09:25:25 AM by alex.asic |
|
i put them both to around 1500. they normally runn 3000+ so what ever you feel like is to low for fans Be aware though that it is only the core temp that is changed by that slider not the chip temp. Thank you i had forgotten about that write up. ill set the temp limit and see how we go. Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher? Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement. Thanks.
Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine. On the auto stop which settings do you use for the fans? lowerfanspeed in and lowerfanspeed out
|
|
|
|
korhank
Newbie
Offline
Activity: 11
Merit: 0
|
|
November 01, 2018, 10:40:45 AM |
|
Any update for Z1 income recovering today?
|
|
|
|
metnet
Newbie
Offline
Activity: 69
Merit: 0
|
|
November 01, 2018, 11:00:17 AM |
|
hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"
of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...
any idea how to set by software to avoid FAN speed check?
any other idea? thanks! /E
hi you can set ignore fan speed via setting section. on the interface of dayun z1, enter the setting and then auto stop miner you can make it off. but be careful you can burned the machine if fan does not properly work.
|
|
|
|
esol
Jr. Member
Offline
Activity: 41
Merit: 6
|
|
November 01, 2018, 01:09:22 PM Last edit: November 01, 2018, 01:27:52 PM by esol |
|
hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"
of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...
any idea how to set by software to avoid FAN speed check?
any other idea? thanks! /E
hi you can set ignore fan speed via setting section. on the interface of dayun z1, enter the setting and then auto stop miner you can make it off. but be careful you can burned the machine if fan does not properly work. thanks so much mate, but I cannot find any "ignore fan speed" setting anywhere; which firmare release? I'm running 20180926. Kindly let me know if Is there a specific entry (and his correct syntax) shown in your JSON Conf, /E update: just installed firmware 20181015, still no clue where to find that "magic" setting...
|
|
|
|
Gstamato3113
Newbie
Offline
Activity: 12
Merit: 0
|
|
November 01, 2018, 02:26:04 PM |
|
hello again
i have a problem. the miner Z1+ generates errors. the daily hash rate is not above 6,5gh/s. is this a problem?
can you advise?
|
|
|
|
lennujuht
Newbie
Offline
Activity: 84
Merit: 0
|
|
November 01, 2018, 04:05:19 PM |
|
Hi, where to download firmware 20181015?
|
|
|
|
PostJok
Newbie
Offline
Activity: 122
Merit: 0
|
|
November 01, 2018, 04:43:39 PM |
|
Will anyone actually ROI on those before you earn 4$/day?
|
|
|
|
|