Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner

[vcon]

Has anyone found  a way to enable SSH on the Z1+?

[Tarlatata]

New miner from Dayun listed here. Any info? Says its a x11 miner 48GH/s

https://www.zigminer.com/miner.html

Nice catch. Tomax is looking at avaibility/specs for me right now.

[alex.asic]

Thanks for that. Not worth buying unless almost free electricity it seems.

New miner from Dayun listed here. Any info? Says its a x11 miner 48GH/s

https://www.zigminer.com/miner.html

Yes ,it is new Dayun miner called Dayun Zig D1 ,x11 miner 48GH/s ,more details you will find from here :

https://www.akminer.com/all-products/new-dayun-x11-d1-ship-now

[streenip]

It’s 1:30 am in China, any improvement on the income?

[xs.over]

It’s 1:30 am in China, any improvement on the income?

Remember a simple thing: nowadays mainly only miming hardware manufacturers and hardware resellers earn money in crypto mining  sphere.

[esol]

hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"

of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...

any idea how to set by software to avoid FAN speed check?

any other idea?
thanks!
/E

[deneme12]

It’s 1:30 am in China, any improvement on the income?

Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words...

[topoolscom]

It’s 1:30 am in China, any improvement on the income?

Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words...

I think dayun.company is not Z1 official website.

[alex.asic]

Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher?  Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement.  Thanks.

[streenip]

Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher?  Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement.  Thanks.

Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.

[alex.asic]

Thank you i had forgotten about that write up. ill set the temp limit and see how we go.

Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher?  Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement.  Thanks.

Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.

[Yezzzuurrr]

Thank you i had forgotten about that write up. ill set the temp limit and see how we go.

Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher?  Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement.  Thanks.

Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.

On the auto stop which settings do you use for the fans? lowerfanspeed in and lowerfanspeed out

[Yezzzuurrr]

It’s 1:30 am in China, any improvement on the income?

Discount coupon is valid until 31 october. Why not november? Because 1st of november nothing will change and people will mark them as a lier. I wrote before write a review for zig 1 in dayun.company and see what happens when they publish. They write good words and 5 star and use your name like it is yours. Never trust any of their words...

i think http://www.dayunmining.com/ is official site?

[alex.asic]

i put them both to around 1500. they normally runn 3000+ so what ever you feel like is to low for fans
Be aware though that it is only the core temp that is changed by that slider not the chip temp.

Thank you i had forgotten about that write up. ill set the temp limit and see how we go.

Gday gents. being in Australia we get some hot temps. today was the first day over 30 in my area. My miners have been shutting down. first on 950 auto and now on 900 auto. Iam assuming that when the temps stay over 50 degrees it will shut off. Looking at the json file it is set to shutdown at 50 degress. has any one changed the temp to 60 or higher?  Iam running the 9.30 software. Or do you reckon re doing the thermal paste will help out enough? The miners are in my garage which isn't plastered so has ok air movement.  Thanks.

Hi, go to the message thread #174...I used these settings suggested by Mordred for my Z1+ and it works as my machine core temperature gets to 52-53 degrees Celsius but it still runs fine.

On the auto stop which settings do you use for the fans? lowerfanspeed in and lowerfanspeed out

[korhank]

Any update for Z1 income recovering today?

[metnet]

hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"

of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...

any idea how to set by software to avoid FAN speed check?

any other idea?
thanks!
/E

hi

you can set ignore fan speed via setting section. on the interface of dayun z1, enter the setting  and then auto stop miner  you can make it off.  but be careful  you can burned the machine if fan does not properly work.

[esol]

hi, my Z1 stopped mining suddenly as I've discovered the dashboard reports outtake fan speed to "0"

of course the fan is connected and running, but most likely the logic board don't recognise anymore the RPM sensor. Some component possibly has gone...

any idea how to set by software to avoid FAN speed check?

any other idea?
thanks!
/E

hi

you can set ignore fan speed via setting section. on the interface of dayun z1, enter the setting  and then auto stop miner  you can make it off.  but be careful  you can burned the machine if fan does not properly work.

thanks so much mate, but I cannot find any "ignore fan speed" setting anywhere;
which firmare release? I'm running 20180926.

Kindly let me know if Is there a specific entry (and his correct syntax) shown in your JSON Conf,
/E

update: just installed firmware 20181015, still no clue where to find that "magic" setting...

[Gstamato3113]

hello again

i have a problem. the miner Z1+ generates errors. the daily hash rate is not above 6,5gh/s. is this a problem?

can you advise?

[lennujuht]

Hi, where to download  firmware 20181015?

[PostJok]

Will anyone actually ROI on those before you earn 4$/day?