Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner

[PostJok]

indeed... and i payed 6k :/ what a first experience with an asic... if only @zigminer could close his farm or lets say his factory with 200000000 z1's we could have a bit more profit as the difficulty could low a bit... :/ what will haooen when vertcoin leaves the algo? the Z1 ready for the trash dump?

Almost everbody knows asicminervalue.com
this website shows that DAYUN ZIG z1 14.50 USD (incl. electricity) 10.89 USD (excluding electricity)
it is completely wrong. i warned them many times. they did not change. actual earning is around 8 usd. they show at least 35 percent more.
i think they are getting money from dayun zig miner resellers to sell more. would you please write to asicminevalue.com that is WRONG calculation or attitude.
you already know right calc. or you can see true calculation their https://cryptominer.deals/product/dayun-zig-z1

Hi

Hundred percent right and dayun zig miner Thief company

You got a Z1 miner, didnt you?
Its hashing, isn´t it?
Dont think Dayun stated somewhere: Guaranteed profits for next 12 months.

Dont buy asics people  

No asics has dropped its profit by 800% in a month its true that it has not been guaranteed but we have lost our money  i dont know why u are defending it

A very interesting comparison in the picture below (please see)

**** Significant company ZigMiner

https://cdn.pbrd.co/images/HPIZkgu.jpg

NICEHASH Profitability calculator

Compare our profit per TH:
October 1 is about 1.7463 BTC
December 1 is about 0.2717 BTC

That means, a reduction of about 6.4 times our daily profit in 60 days ( 0.2717 x 642% = 1.7463 BTC ), only 60 days
And this is a disaster
For a company that wants to compete with companies like Bitmain and Innosilicon.
Dear. ZigMiner; in real ,You've failed, not your customers

  don´t buy Asics people, the equihash miners got lucky that zcash, komodo etc didn´t fork off  . there are mostly shitcoins on lyra. But blaming a company for less profit is just bad guys. On top the hole market went awole too.

[1714006282]

1714006282

[1714006282]

1714006282

[1714006282]

1714006282

[1714006282]

1714006282

[ipan76]

Has any1 came across a problem with Dayun Zig Z1+ where a massage "An Internal Server Error Occurred" on their browser when trying to connect to the miner?
At first when I got connected to  the miner the interface got changed slightly, and it worked like that for week or two.

At this moment I can see the miner on my router, and also it appears active on Nice Hash.
No changes were maid on the miner or the router prior this.
I'm using latest Chrome browser, and the router is https://www.asus.com/Networking/RTN12Plus/.

I did try to reset Chrome's settings, cookies etc...still the same   

Any suggestions and help will be greatly appreciated

[Yezzzuurrr]

Are you in the .1 network? 192.168.1.0?

Has any1 came across a problem with Dayun Zig Z1+ where a massage "An Internal Server Error Occurred" on their browser when trying to connect to the miner?
At first when I got connected to  the miner the interface got changed slightly, and it worked like that for week or two.

At this moment I can see the miner on my router, and also it appears active on Nice Hash.
No changes were maid on the miner or the router prior this.
I'm using latest Chrome browser, and the router is https://www.asus.com/Networking/RTN12Plus/.

I did try to reset Chrome's settings, cookies etc...still the same   

Any suggestions and help will be greatly appreciated

[ipan76]

Yes, its connected to a second router and the IP is 192.168.1.49
 

Are you in the .1 network? 192.168.1.0?

Has any1 came across a problem with Dayun Zig Z1+ where a massage "An Internal Server Error Occurred" on their browser when trying to connect to the miner?
At first when I got connected to  the miner the interface got changed slightly, and it worked like that for week or two.

At this moment I can see the miner on my router, and also it appears active on Nice Hash.
No changes were maid on the miner or the router prior this.
I'm using latest Chrome browser, and the router is https://www.asus.com/Networking/RTN12Plus/.

I did try to reset Chrome's settings, cookies etc...still the same   

Any suggestions and help will be greatly appreciated

[Yezzzuurrr]

And is your router connected to the internet provider router on the normal internet port connection or did you connect it like a switch? My internet provider router is in the .0 range and it is connected like a switch so i can reach the miner in the .0 range... i only have to change the ip first when i put new firmware on because its standard in de .1 range. Did you try to reboot your routers and after that the power of the miner for 5 minutes and retry?

Yes, its connected to a second router and the IP is 192.168.1.49
 

Are you in the .1 network? 192.168.1.0?

Has any1 came across a problem with Dayun Zig Z1+ where a massage "An Internal Server Error Occurred" on their browser when trying to connect to the miner?
At first when I got connected to  the miner the interface got changed slightly, and it worked like that for week or two.

At this moment I can see the miner on my router, and also it appears active on Nice Hash.
No changes were maid on the miner or the router prior this.
I'm using latest Chrome browser, and the router is https://www.asus.com/Networking/RTN12Plus/.

I did try to reset Chrome's settings, cookies etc...still the same   

Any suggestions and help will be greatly appreciated

[areyouathief]

December 1 is about 0.2717 BTC

That means, a reduction of about 6.4 times our daily profit in 60 days ( 0.2717 x 642% = 1.7463 BTC ), only 60 days
And this is a disaster
For a company that wants to compete with companies like Bitmain and Innosilicon.
Dear. ZigMiner; in real ,You've failed, not your customers

  don´t buy Asics people, the equihash miners got lucky that zcash, komodo etc didn´t fork off  . there are mostly shitcoins on lyra. But blaming a company for less profit is just bad guys. On top the hole market went awole too.

ZigMiner just did a quick, multimillion $$ profit - so, they've failed?

[Wolf6270]

Hi all ! faced such a problem, my miner works on firmware 09.14 + overclocking the core to 1000 and the auto frequency is set to 1. but there is no stability! with all this, it consumes 1500 watts of power! There are skoks up to 20 gigahash! and on the pool, too, these slopes are fixed! But I noticed that not all panels on the blade became active, but at the same time each blade gives out in peak to 10-15 gigagesh! which pushes to the idea that it is quite likely that the manufacturer has programmatically limited the power to 6.8 gigahesh! and sorry for the mistakes, I'm just from Russia)))
https://ibb.co/2Nyn4Q0
https://ibb.co/r5VRtdk
https://ibb.co/Y09yzHx
https://ibb.co/7nK6cKX

[metnet]

Hi all ! faced such a problem, my miner works on firmware 09.14 + overclocking the core to 1000 and the auto frequency is set to 1. but there is no stability! with all this, it consumes 1500 watts of power! There are skoks up to 20 gigahash! and on the pool, too, these slopes are fixed! But I noticed that not all panels on the blade became active, but at the same time each blade gives out in peak to 10-15 gigagesh! which pushes to the idea that it is quite likely that the manufacturer has programmatically limited the power to 6.8 gigahesh! and sorry for the mistakes, I'm just from Russia)))
https://ibb.co/2Nyn4Q0
https://ibb.co/r5VRtdk
https://ibb.co/Y09yzHx
https://ibb.co/7nK6cKX

yes it is true. my device z1 and my friend device is  z1, too. we bought them almost same date. both we are using 1409 image verison. we used same config but he made oc to 1000 mhz but i can not. think about how come it is possible. this is strange.

[Andartis]

yes it is true. my device z1 and my friend device is  z1, too. we bought them almost same date. both we are using 1409 image verison. we used same config but he made oc to 1000 mhz but i can not. think about how come it is possible. this is strange.

This is called "silicon lottery". Google it.

[metnet]

yes it is true. my device z1 and my friend device is  z1, too. we bought them almost same date. both we are using 1409 image verison. we used same config but he made oc to 1000 mhz but i can not. think about how come it is possible. this is strange.

This is called "silicon lottery". Google it.

yes i read it thanks. but it is little bit different. i think manufacturer limited some machines by bios. and then they announced zig1 plus. they sold more.

[HPrivakos]

to @zigminer founder
thanks for new image and fan speed option.
as you said below, we wait the autorestart option for low hashrate and hashboard.

i wonder that will these machines able to run lyra2rev3 in near future or any other algo.

about overclock , maybe next version. i need more test .
about hashrate goes down ,  just config autorestart , if hashrate low , auto restart will slove this problem.

Please stop crying for everything, make a minimum of research and read closely what he wrote...

"JUST CONFIG AUTORESTART", the option is already available, since the first release...
It's not zigminer fault if you can't even read a small dashboard

[astraleureka]

yes it is true. my device z1 and my friend device is  z1, too. we bought them almost same date. both we are using 1409 image verison. we used same config but he made oc to 1000 mhz but i can not. think about how come it is possible. this is strange.

This is called "silicon lottery". Google it.

yes i read it thanks. but it is little bit different. i think manufacturer limited some machines by bios. and then they announced zig1 plus. they sold more.

You can believe what you like, but if they're the same revision and the same firmware, it's a silicon lottery issue.

[metnet]

to @zigminer founder
thanks for new image and fan speed option.
as you said below, we wait the autorestart option for low hashrate and hashboard.

i wonder that will these machines able to run lyra2rev3 in near future or any other algo.

about overclock , maybe next version. i need more test .
about hashrate goes down ,  just config autorestart , if hashrate low , auto restart will slove this problem.

Please stop crying for everything, make a minimum of research and read closely what he wrote...

"JUST CONFIG AUTORESTART", the option is already available, since the first release...
It's not zigminer fault if you can't even read a small dashboard

who is crying? please pay attention what you wrote.

its old config what you mentioned does not work. you should try before you talk.
and zigminer said that "i will develop new autorestarter option depends on hashrate.

[metnet]

yes it is true. my device z1 and my friend device is  z1, too. we bought them almost same date. both we are using 1409 image verison. we used same config but he made oc to 1000 mhz but i can not. think about how come it is possible. this is strange.

This is called "silicon lottery". Google it.

yes i read it thanks. but it is little bit different. i think manufacturer limited some machines by bios. and then they announced zig1 plus. they sold more.

You can believe what you like, but if they're the same revision and the same firmware, it's a silicon lottery issue.

yes you are right. they manufactured these devices. and then they explorered some chips that runs at higher Mhz. and then they separated them.
after that they manufactured z1 PLUS with separated chips that running higher mhz.

[Andartis]

yes you are right. they manufactured these devices. and then they explorered some chips that runs at higher Mhz. and then they separated them.
after that they manufactured z1 PLUS with separated chips that running higher mhz.

Thats how it works. Also: If someone wants to overclock seriously, he would also ask for voltage control, not only frequency.

[astraleureka]

yes you are right. they manufactured these devices. and then they explorered some chips that runs at higher Mhz. and then they separated them.
after that they manufactured z1 PLUS with separated chips that running higher mhz.

Thats how it works. Also: If someone wants to overclock seriously, he would also ask for voltage control, not only frequency.

If the voltage regulation on these are the same as the PinIdea RR-210, there is no programmatic control available.

[lennujuht]

What is the better settings for  AUTORESTART ?

[metnet]

What is the better settings for  AUTORESTART ?

hashrate autorestart does not work.(@zigminer try to solve it soon i think.)
only working autorestart error counting.

[lennujuht]

Thanks! what about difficulty, if I add in pool password C=BTC,D=512 ?

What is the better settings for  AUTORESTART ?

hashrate autorestart does not work.(@zigminer try to solve it soon i think.)
only working autorestart error counting.

[metnet]

@zigminer

frequently one or two hashboard goes 0 (zero). if it goes to 0, it stays long time unless device restart.
would you please make it new image that detect low hashrate and zero and restart just one or two hashboard separately.

thanks in advance.