sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 11, 2021, 10:42:55 AM Last edit: November 08, 2021, 01:10:30 PM by mprep |
|
Can you verify how ethermine is on your 3090? I can crank the intensity upto 350 without issue but I see 224 being suggested a lot. Thoughts?
--xintensity 350 produce more stale shares than 224 and ethermine seems to have a reduced payout for stales, but you can try. Increased intensity usually give more hashrate, but more stale shares and powerusage. miningpoolhub.com pay for stale shares and 350 can be used with good results.
10 mhs slower with 6 gpu rig, just try it a couple minute ago
What cards in the rig, which pool, which launch configuration?
Can't exclude cards when AMD and Nvidia cards are selected.
This is is supported run tbminer --list-devices Manually specify which devices you want, start with cl, then cuda. Make sure that you don't select the same device for cuda and cl because cl is supported for NVIDIA devices as well --cl-devices [1,2] --cuda-devices [0,2] [moderator's note: consecutive posts merged]
|
|
|
|
ep690d01
Newbie
Offline
Activity: 21
Merit: 0
|
|
October 11, 2021, 01:44:25 PM |
|
384m [2021-10-11 15:42:39.022] eu1.ethermine.org (ethash) PING: 98ms DIFFICULTY: 1.00 EPOCH: 446 384m [2021-10-11 15:42:39.022] 384m [2021-10-11 15:42:39.022] 384m [2021-10-11 15:42:39.022] ID BOARD TYPE TEMP FAN CORE MEM WATT kW/h COST/h 384m [2021-10-11 15:42:39.022] GPU0 5500XT OpenCL 0/0 0 0 0 0 0.00 0.00USD 384m [2021-10-11 15:42:39.022] 0 0.00 0.00USD 384m [2021-10-11 15:42:39.022] 384m [2021-10-11 15:42:39.022] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES 384m [2021-10-11 15:42:39.022] GPU0 5500XT 0.00 H/W 27.75 MH/s 27.85 MH/s 149/0/2 (100.00) 384m [2021-10-11 15:42:39.022] 0.00 H/W 27.75 MH/s 27.85 MH/s 149/0/2 (100.00) 384m [2021-10-11 15:42:39.022]
last version --xintensity 64
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 11, 2021, 02:03:32 PM |
|
384m [2021-10-11 15:42:39.022] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES 384m [2021-10-11 15:42:39.022] GPU0 5500XT 0.00 H/W 27.75 MH/s 27.85 MH/s 149/0/2 (100.00)
On the 5500XT try --xintensity 24, no stales poolside, lower power
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
|
October 11, 2021, 02:16:37 PM |
|
Is xintensity 224 still recommended for nvidia cards mining on miningpoolhub?
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 11, 2021, 03:06:10 PM Last edit: November 08, 2021, 01:09:09 PM by mprep |
|
On miningpoolhub try --xintensity 352 (suggested by one of the other users)
We are making a watchdog to be able to detect gpu's that are hanging / timed out. Hopefully done in v1.14 [moderator's note: consecutive posts merged]
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
|
October 11, 2021, 03:42:08 PM |
|
On miningpoolhub try --xintensity 352 (suggested by one of the other users)
Is there a thread link to this suggestion? Also, would that increase more stale shares submitted since we are increasing the xintensity?
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 11, 2021, 04:21:42 PM Last edit: October 11, 2021, 04:50:21 PM by sp_ |
|
Is there a thread link to this suggestion? Also, would that increase more stale shares submitted since we are increasing the xintensity?
Scroll a few pages back and look at the pictures. Miningpoolhub pay 100% for stale shares so it doesn't matter. 2miners, nanopool, wollypooly 100% as well. ezil.me 70% , hiveon.com 80%. Flexpool, ethermine, nicehash, binance pay 0%. So the configuration of the mining software needs to be changed accordingly Note that the ethereum blockchain rewards stale work/blocks. They are called uncle blocks. The uncle blocks are protecting the security of the blockchain. For bitcoin based blockchains stale work is not rewarded and not needed.
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
|
October 11, 2021, 05:12:09 PM |
|
Is there a thread link to this suggestion? Also, would that increase more stale shares submitted since we are increasing the xintensity?
Scroll a few pages back and look at the pictures. Miningpoolhub pay 100% for stale shares so it doesn't matter. 2miners, nanopool, wollypooly 100% as well. ezil.me 70% , hiveon.com 80%. Flexpool, ethermine, nicehash, binance pay 0%. So the configuration of the mining software needs to be changed accordingly Note that the ethereum blockchain rewards stale work/blocks. They are called uncle blocks. The uncle blocks are protecting the security of the blockchain. For bitcoin based blockchains stale work is not rewarded and not needed. Thanks for the explanation. I updated the xintensity to 352 and currently mining on miningpoolhub.com. Will provide results in the next 8-10 hours.
|
|
|
|
abanamat
Jr. Member
Offline
Activity: 274
Merit: 1
|
|
October 11, 2021, 07:03:14 PM |
|
Still use 1.09 with better results than latest versions
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 11, 2021, 07:15:36 PM |
|
In the later versions on Nvidia you need to multiply the xintensity by 4 (cuda 11.4 build)
1.09: rtx 3080 --xintensity 300... 109MHASH 1.13: rtx 3080 --xintensity 1200... 109MHASH
We nerfed it because of too many stale shares and poor results on some pools.
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
|
October 12, 2021, 01:12:03 AM |
|
Is there a thread link to this suggestion? Also, would that increase more stale shares submitted since we are increasing the xintensity?
Scroll a few pages back and look at the pictures. Miningpoolhub pay 100% for stale shares so it doesn't matter. 2miners, nanopool, wollypooly 100% as well. ezil.me 70% , hiveon.com 80%. Flexpool, ethermine, nicehash, binance pay 0%. So the configuration of the mining software needs to be changed accordingly Note that the ethereum blockchain rewards stale work/blocks. They are called uncle blocks. The uncle blocks are protecting the security of the blockchain. For bitcoin based blockchains stale work is not rewarded and not needed. Thanks for the explanation. I updated the xintensity to 352 and currently mining on miningpoolhub.com. Will provide results in the next 8-10 hours. Been running TBM 1.13 with xintensity 352 for 8 hours and my results are below: 485m [2021-10-11 20:07:37.418] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES 485m [2021-10-11 20:07:37.418] GPU0 3060Ti 436.17 kH/W 64.99 MH/s 64.99 MH/s 133/0/0 (100.00) 485m [2021-10-11 20:07:37.418] GPU1 3060Ti 362.99 kH/W 64.98 MH/s 64.98 MH/s 155/0/0 (100.00) 485m [2021-10-11 20:07:37.418] GPU2 3060Ti 435.92 kH/W 64.95 MH/s 64.95 MH/s 134/1/0 (99.26) 485m [2021-10-11 20:07:37.418] GPU3 3060Ti 363.04 kH/W 64.98 MH/s 64.98 MH/s 128/0/0 (100.00) 485m [2021-10-11 20:07:37.418] GPU4 3060Ti 435.91 kH/W 64.95 MH/s 64.96 MH/s 135/0/0 (100.00) 485m [2021-10-11 20:07:37.418] GPU5 3060Ti 436.15 kH/W 64.99 MH/s 64.99 MH/s 160/0/0 (100.00) 485m [2021-10-11 20:07:37.418] 2470.18 kH/W 389.84 MH/s 389.85 MH/s 845/1/0 (99.88)
|
|
|
|
somaton
Jr. Member
Offline
Activity: 211
Merit: 6
|
|
October 12, 2021, 02:04:54 AM |
|
Still use 1.09 with better results than latest versions
Same here, if gpu is limited by tdp, any version after 1.09 will be much slower compared to any other miners. Only with core-lock 1.10 and newer will be as fast as 1.09. What i dont like in 1.09 - high cpu usage.
|
|
|
|
Ramsete2
Jr. Member
Offline
Activity: 87
Merit: 5
|
|
October 12, 2021, 05:28:36 AM |
|
Which xintensity should I set on Flexpool for the following cards to get the best performances? - NVIDIA RTX 3080 and 3070 (not LHR)
- AMD RX 6800 and 6800 XT
Thanks.
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 12, 2021, 06:24:11 AM Last edit: November 08, 2021, 01:09:24 PM by mprep |
|
Only with core-lock 1.10 and newer will be as fast as 1.09. What i dont like in 1.09 - high cpu usage.
Core lock? Increase the Temp limit so the cards don't trottle. The cpu usage in 1.09 is increasing the hashrate with 1-2% on low intensity but using too much power to be justified. We can add a flag --cpu-mining in the next version. If you use 1.09 with --xintensity you have to multiply by 4 to compare the two versions.
Been running TBM 1.13 with xintensity 352 for 8 hours and my results are below:
485m [2021-10-11 20:07:37.418] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES 485m [2021-10-11 20:07:37.418] GPU0 3060Ti 436.17 kH/W 64.99 MH/s 64.99 MH/s 133/0/0 485m [2021-10-11 20:07:37.418] 2470.18 kH/W 389.84 MH/s 389.85 MH/s 845/1/0 (99.88)
Looks good with no calculated stale shares. The most important is how is the payout / poolside reward? Try with --xintensity 1408
Which xintensity should I set on Flexpool for the following cards to get the best performances? - NVIDIA RTX 3080 and 3070 (not LHR)
- AMD RX 6800 and 6800 XT
On flexpool you should mine on the high difficulty port. Why don't you try out 10 intensities and check yourself? What hashrate are you getting with rtx 3080 --xintensity 1200 ? Amd cards works best with lower --xintensities than NVIDIA teamred miner: 58.8 s-eth.2miners.com:2020 (ethash) DIFFICULTY: 2.03 EPOCH: 440 (At least 2 shares/10 mins at each intensity) 'Stock' settings - 6800xt (2400 clock / 1990 mem) Xintensity = -1: 62.32 Xintensity = 1: 58.51 - 213W Xintensity = 12: 61.10 Xintensity = 24: 61.94 Xintensity = 36: 62.03 Xintensity = 48: 62.11 Xintensity = 78: 62.15 Xintensity = 128: 62.33 Xintensity = 240: 62.60 Xintensity = 360: 62.64 Xintensity = 512: 62.70 - 230W No shares reject
[moderator's note: consecutive posts merged]
|
|
|
|
Ramsete2
Jr. Member
Offline
Activity: 87
Merit: 5
|
|
October 12, 2021, 07:41:51 AM |
|
Testing Flexpool with xintensity 896:
│[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] flexpool.io (ethash) PING: 26ms DIFFICULTY: 0.931 EPOCH: 446 │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] ID BOARD TYPE TEMP FAN CORE MEM WATT kW/h COST/h │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] GPU0 3080 Cuda 50/0 55 1050 10201 224 0.22 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] GPU1 3080 Cuda 43/0 50 1050 10201 217 0.22 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] GPU2 3080 Cuda 51/0 50 1050 10201 222 0.22 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] GPU3 3080 Cuda 49/0 50 1050 10201 221 0.22 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] GPU4 3080 Cuda 50/0 54 1050 10201 215 0.21 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU5 3080 Cuda 50/0 56 1050 10201 221 0.22 0.02USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] 1320 1.32 0.13USD │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU0 3080 455.01 kH/W 101.92 MH/s 102.13 MH/s 36/0/8 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU1 3080 471.69 kH/W 102.36 MH/s 102.31 MH/s 29/0/5 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU2 3080 460.93 kH/W 102.33 MH/s 102.31 MH/s 21/0/3 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU3 3080 462.98 kH/W 102.32 MH/s 102.31 MH/s 21/0/3 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU4 3080 475.96 kH/W 102.33 MH/s 102.32 MH/s 23/0/2 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] GPU5 3080 463.04 kH/W 102.33 MH/s 102.32 MH/s 25/0/3 (100.00%) │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.270] 2789.60 kH/W 613.59 MH/s 613.70 MH/s 155/0/24 (100.00%)
|
|
|
|
Michael20
Member
Offline
Activity: 118
Merit: 10
|
|
October 12, 2021, 07:46:34 AM |
|
1-2 times 1.13 got lagging, so no new entry to see, gpu temp also show no mining because its cold. Faith enter helped. So go back to 1.11 same if you mark something in the miner, or slide up with the bar and hold there. It seems after Enter it starts again, and gpu temp is raising. Hope you understand my bad english
|
|
|
|
Ramsete2
Jr. Member
Offline
Activity: 87
Merit: 5
|
|
October 12, 2021, 08:10:38 AM |
|
When I start the miner I always got these warnings, is it normal?
│[2021-10-12 08:08:40][info][miner/0]: 0m [2021-10-12 08:08:38.199] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:08:40][info][miner/0]: 0m [2021-10-12 08:08:38.218] GPU5 Dag buffer verified ok! │[2021-10-12 08:08:42][info][miner/0]: 0m [2021-10-12 08:08:40.691] Job d99abc21 │[2021-10-12 08:08:43][info][miner/0]: 0m [2021-10-12 08:08:41.434] Job 7f2c7774 │[2021-10-12 08:08:46][info][miner/0]: 0m [2021-10-12 08:08:44.199] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:08:46][info][miner/0]: 0m [2021-10-12 08:08:44.408] Job 0be78c4e │[2021-10-12 08:08:49][info][miner/0]: 0m [2021-10-12 08:08:47.380] Job c2223eb4 │[2021-10-12 08:08:51][info][miner/0]: 0m [2021-10-12 08:08:49.610] Job 5978c555 │[2021-10-12 08:08:52][info][miner/0]: 0m [2021-10-12 08:08:50.200] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:08:55][info][miner/0]: 0m [2021-10-12 08:08:53.327] Job 68aae417 │[2021-10-12 08:08:58][info][miner/0]: 0m [2021-10-12 08:08:56.200] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:08:58][info][miner/0]: 0m [2021-10-12 08:08:56.299] Job e3bdd953 │[2021-10-12 08:09:01][info][miner/0]: 0m [2021-10-12 08:08:59.272] Job 86b4891b │[2021-10-12 08:09:04][info][miner/0]: 0m [2021-10-12 08:09:02.200] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:09:04][info][miner/0]: 0m [2021-10-12 08:09:02.245] Job 9f793b52 │[2021-10-12 08:09:07][info][miner/0]: 0m [2021-10-12 08:09:05.218] Job 111e356d │[2021-10-12 08:09:10][info][miner/0]: 0m [2021-10-12 08:09:08.200] Cannot initialize API server. Port in use. Retrying in 6 secs │[2021-10-12 08:09:10][info][miner/0]: 0m [2021-10-12 08:09:08.933] Job 2aa7c9b6 │[2021-10-12 08:09:13][info][miner/0]: 0m [2021-10-12 08:09:11.906] Job 5da54083
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 12, 2021, 08:35:54 AM Last edit: November 08, 2021, 01:09:44 PM by mprep |
|
Testing Flexpool with xintensity 896: │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] flexpool.io (ethash) PING: 26ms DIFFICULTY: 0.931 EPOCH: 446
You are using port 4444 on flexpool which is 4GH if you use high intensity switch to port 14444 which is 100GH. If not, you will get too many stale shares..
When I start the miner I always got these warnings, is it normal?
Do you have 2 instances of the miner running on the same computer? Find the option to switch off the api, or change the api port
1-2 times 1.13 got lagging, so no new entry to see, gpu temp also show no mining because its cold. Press enter helped.
This is an issue in windows 10 if you mark text in the commandline window, the app will stop mining. f.ex by rightclicking in it. Has nothing to do with the version number.
I suggest that you report issues on our github https://github.com/sp-hash/TeamBlackMiner/issues4 open, 53 closed. The watchdog has been completed in v1.14. If a gpu crash because of high oc and don't report hashrate in 3 minutes, the watchdog will restart the thread. This will improve the performance on rigs with "has timed out" messages. Every time the EPOC changes, TBMiner have to recalculate the DAG buffer. If the rig is tuned too high clocks, v1.00 - v1.13 could crash with "has timed out" messages. [moderator's note: consecutive posts merged]
|
|
|
|
Ramsete2
Jr. Member
Offline
Activity: 87
Merit: 5
|
|
October 12, 2021, 09:39:21 AM Last edit: November 08, 2021, 01:08:25 PM by mprep |
|
Testing Flexpool with xintensity 896: │[2021-10-12 07:39:34][info][miner/0]: 19m [2021-10-12 07:39:33.269] flexpool.io (ethash) PING: 26ms DIFFICULTY: 0.931 EPOCH: 446
You are using port 4444 on flexpool which is 4GH if you use high intensity switch to port 14444 which is 100GH. If not, you will get too many stale shares.. I switched to 100GH port but still got too many stales (xintensity at 1024 at the moment): │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU0 3080 453.35 kH/W 102.00 MH/s 102.30 MH/s 12/0/1 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU1 3080 457.05 kH/W 102.38 MH/s 102.36 MH/s 5/0/0 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU2 3080 465.35 kH/W 102.38 MH/s 102.36 MH/s 8/0/1 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU3 3080 455.02 kH/W 102.38 MH/s 102.36 MH/s 2/0/1 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU4 3080 463.25 kH/W 102.38 MH/s 102.36 MH/s 5/0/4 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] GPU5 3080 476.15 kH/W 102.37 MH/s 102.36 MH/s 9/0/1 (100.00%) │[2021-10-12 09:37:06][info][miner/0]: 91m [2021-10-12 09:37:05.284] 2770.18 kH/W 613.89 MH/s 614.11 MH/s 41/0/8 (100.00%) I'm thinking to try MiningPoolHub, is it OK to keep xintensity to 1024 for this pool?
Got a problem with one of my rigs (2x3070 + 4x3080) Miner doesn't start with this errors: │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.279] GPU3 Dag buffer verified ok! │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.281] GPU2 Dag buffer verified ok! │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.293] GPU0 Dag buffer verified ok! │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.293] GPU5 Dag buffer verified ok! │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.769] GPU4 Dag verification failed. Exiting... │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.769] Shutting down threads │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.770] Stratum thread exited │[2021-10-12 10:07:56][info][miner/0]: 0m [2021-10-12 10:07:55.778] GPU1 Dag verification failed. Exiting... Don't know what to do... [moderator's note: consecutive posts merged]
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
|
October 12, 2021, 10:23:31 AM |
|
reduce the clocks and or increase power on gpu4. --xintensity 1024 is fine with miningpoolhub. Stales are rewarded 100%, so stale count doesn't matter
|
|
|
|
|