WiWi
Member
Offline
Activity: 83
Merit: 10
|
|
October 15, 2014, 10:49:28 AM Last edit: October 15, 2014, 01:20:53 PM by WiWi |
|
Hi, For sure the board was tested. you have to check coolers attachment. use the whole set you had on your previous board. Give me TW access or contact Martin on skype
Regards: Vesi
Hi, vesi did indeed use the set on the previous board. I am available now for TeamViewer connection, i'll send a PM in 2 minutes. Ok, PM send edit: tried 0_4_0, does not work at all. Switched back to version 0_3_9 again thx to martin i know what to do now.
|
|
|
|
technobitVesi
Newbie
Offline
Activity: 65
Merit: 0
|
|
October 15, 2014, 12:38:19 PM |
|
Hi, For sure the board was tested. you have to check coolers attachment. use the whole set you had on your previous board. Give me TW access or contact Martin on skype
Regards: Vesi
Hi, vesi did indeed use the set on the previous board. I am available now for TeamViewer connection, i'll send a PM in 2 minutes. Ok, PM send edit: tried 0_4_0, does not work at all. Switched back to version 0_3_9 again Hi, It is written in 0_4_0 changelog after flashing device go ssh to the unit and type "fix_rc" + Enter the unit will reboot now everything should work as before Regards Vesi
|
|
|
|
WiWi
Member
Offline
Activity: 83
Merit: 10
|
|
October 15, 2014, 02:42:39 PM |
|
H Vesi,
Martin did help me on skype, the source of the problem is detected.
I'll send you PM about it
reagrds Wilco
|
|
|
|
Cortex7
|
|
October 16, 2014, 04:02:30 AM |
|
Hi Vesi,
order# HCRSHRFOY
2 x tplinks still not shipped yet?
Paid in full some time ago.
|
|
|
|
technobitVesi
Newbie
Offline
Activity: 65
Merit: 0
|
|
October 17, 2014, 08:28:04 PM |
|
HI, Sorry I did missed this. Will be fixed Monday
Regards: Vesi
|
|
|
|
WiWi
Member
Offline
Activity: 83
Merit: 10
|
|
October 18, 2014, 06:46:54 AM |
|
hi Vesi, Did you see the PM i send you?
|
|
|
|
me2014
|
|
October 19, 2014, 09:36:45 PM |
|
|
|
|
|
bboerst
Newbie
Offline
Activity: 18
Merit: 0
|
|
October 19, 2014, 11:59:58 PM |
|
Vesi- Can you please tell me what the value of the capacitor is at the location in red below? I have one board where this cap failed and I need to get a replacement: https://i.imgur.com/zlQZr21l.jpg
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
October 20, 2014, 12:37:43 AM |
|
Try to change hexminerm-reset-below-threshold setting to 75
|
|
|
|
Cortex7
|
|
October 20, 2014, 01:47:13 PM |
|
HI, Sorry I did missed this. Will be fixed Monday
Regards: Vesi
OK, thx vesi!
|
|
|
|
me2014
|
|
October 20, 2014, 02:56:11 PM |
|
Try to change hexminerm-reset-below-threshold setting to 75 already done..dont know whats going on,think it is the board problem because when I disconnect problematic board,it works fine :/
|
|
|
|
2GOOD
|
|
October 21, 2014, 07:13:27 AM |
|
Try to change hexminerm-reset-below-threshold setting to 75 already done..dont know whats going on,think it is the board problem because when I disconnect problematic board,it works fine :/ set hexminerm-reset-below-threshold even lower: 10 for example You can also flash back the router with version 3.8.0, don't forget to reset the settings.
|
|
|
|
me2014
|
|
October 21, 2014, 07:29:51 AM |
|
is 3.8 version better than 4.0 or what?
|
|
|
|
2GOOD
|
|
October 21, 2014, 07:40:28 AM |
|
is 3.8 version better than 4.0 or what?
3.8 lacks this "feature" of resetting the device if hashrate is bellow some percentage.
|
|
|
|
me2014
|
|
October 21, 2014, 07:45:11 AM |
|
kk,thanks..I will try that today..
|
|
|
|
technobitVesi
Newbie
Offline
Activity: 65
Merit: 0
|
|
October 22, 2014, 06:02:42 AM |
|
|
|
|
|
CH
Newbie
Offline
Activity: 22
Merit: 1
|
|
October 22, 2014, 03:41:40 PM |
|
Update: I can see a performance increase of about 200 to 300 GHs since yesterday evening. Thanks.
|
|
|
|
marto74 (OP)
|
|
October 23, 2014, 07:56:27 AM |
|
Hi, All and Bick I am back. I want to thank Mr Teal for the support too.
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
October 23, 2014, 08:03:51 AM |
|
Hi, All and Bick I am back. I want to thank Mr Teal for the support too.
Welcome back marto
|
|
|
|
retrogeek
Newbie
Offline
Activity: 9
Merit: 0
|
|
October 23, 2014, 11:02:50 AM |
|
I am back.
Hi Marto Welcome back! Hoping you can point me in the direction. I had a small problem with my cheap power supply - it melted the cables and damaged my HEX4M board. I've tried to clean up the board but it needs some replacement components: http://i1383.photobucket.com/albums/ah297/bob171/HEX4m_damaged_b_zpsee6233cc.jpgDoes this look like a straightforward repair? Thanks b
|
|
|
|
|