grotoc
|
|
June 07, 2014, 07:31:20 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 07:32:44 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
That is strange, blocks are being detected while solo mining. Did you specify algo=x11 in your conf?
|
|
|
|
grotoc
|
|
June 07, 2014, 07:34:52 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
That is strange, blocks are being detected while solo mining. Did you specify algo=x11 in your conf? Yes I've got the right config file. My daemon see the blocks, but my stratum (based on NOMP) does not detect them, so I'm unable to calculate shares.
|
|
|
|
SlientBit
|
|
June 07, 2014, 07:39:27 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
That is strange, blocks are being detected while solo mining. Did you specify algo=x11 in your conf? Yes I've got the right config file. My daemon see the blocks, but my stratum (based on NOMP) does not detect them, so I'm unable to calculate shares. can't help, no coding skills whatsoever
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 07:44:40 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
That is strange, blocks are being detected while solo mining. Did you specify algo=x11 in your conf? Yes I've got the right config file. My daemon see the blocks, but my stratum (based on NOMP) does not detect them, so I'm unable to calculate shares. can't help, no coding skills whatsoever I just had a 2nd chain roll back. Sometimes this is caused because the network is yet to stabilize and we need more miners/clients on the new chain. The difficulties need to get higher and then the network will stabilize. Probably this is the problem your pool is facing. Please try after the network stabilizes. Just solo mine till then.
|
|
|
|
grotoc
|
|
June 07, 2014, 08:05:14 PM |
|
It's a bit messy. I have coins that appear, then disappear... Then I can mine others, then they disappear also... What's the right fork ? I'm at 114840 but it's still going very very fast...
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 08:08:25 PM |
|
It's a bit messy. I have coins that appear, then disappear... Then I can mine others, then they disappear also... What's the right fork ? I'm at 114840 but it's still going very very fast...
Give some time for the network to stabilize. There are 2 chains at present so it is a bit messy. Once everyone start to mine on this chain, it should be fine.
|
|
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 08:27:40 PM |
|
Hughjays, the difficulties are very low at start. Blocks will be found every second when the difficulty starts at 0.002 for any algo and any coin. Once the difficulty is higher, only then will a block be found every 90 secs.
|
|
|
|
cloudminers
|
|
June 07, 2014, 08:28:46 PM |
|
I don't think I will be able to solve it. The dev must have change something that makes my stratum unable to detect that valid blocks are ...valid ! I never have this issue with my other X11 pool.
That is strange, blocks are being detected while solo mining. Did you specify algo=x11 in your conf? Yes I've got the right config file. My daemon see the blocks, but my stratum (based on NOMP) does not detect them, so I'm unable to calculate shares. can't help, no coding skills whatsoever I just had a 2nd chain roll back. Sometimes this is caused because the network is yet to stabilize and we need more miners/clients on the new chain. The difficulties need to get higher and then the network will stabilize. Probably this is the problem your pool is facing. Please try after the network stabilizes. Just solo mine till then. The chain roll back caused issues at our pool. I just re-downloaded the block chain and performed some minor fixes, mining should be fine again.
|
|
|
|
|
hughjays77
|
|
June 07, 2014, 08:37:07 PM |
|
64.36 TH/s reported as Network Rate and 1 block per second for past 10 hours
Is this correct
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 08:38:36 PM |
|
64.36 TH/s reported as Network Rate and 1 block per second for past 10 hours
Is this correct
No. The p2p pools are not updated. The admin told me that he would update after a couple of hours.
|
|
|
|
hughjays77
|
|
June 07, 2014, 08:42:52 PM |
|
I have no idea where the hash power is coming from FFS !!! Blocks are coming in so fast (>2 /S ) that I get 0 shares ... WFT?? What am I missing?? Where's all that hashpower
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 08:45:40 PM |
|
I have no idea where the hash power is coming from FFS !!! Blocks are coming in so fast (>2 /S ) that I get 0 shares ... WFT?? What am I missing?? Where's all that hashpower Please wait the network is yet to stabilize due to 2 chains. Once more miners and nodes shift to this chain, everything will be fine.
|
|
|
|
Watchy312
Member
Offline
Activity: 193
Merit: 10
|
|
June 07, 2014, 08:46:28 PM |
|
Is there a blake pool?
|
|
|
|
saffroncoin (OP)
|
|
June 07, 2014, 08:48:26 PM |
|
Is there a blake pool?
Not yet. We are looking for a pool creator for it. This blake can't be merged mined yet.
|
|
|
|
grotoc
|
|
June 07, 2014, 08:52:06 PM |
|
We always go back to block 114640...
|
|
|
|
hughjays77
|
|
June 07, 2014, 08:53:02 PM |
|
Is their a working X11 pool?
|
|
|
|
|