ASICMINER Auction: 50 Block Erupter Blades CHECK OP FOR PAYMENT

[teek]

anyone elses shipment "on hold"  ?   also i signed up for e-mail notification and did not receive a more detailed e-mail as some are saying..

were is your shipment on hold? You got 10 blades, right. Is it been shipped in single box?

e-mail notifications - waste of time, it will not provide more detailed info then you can see on web site.

yeah friedcat confirmed there is some customs issue and he is dealing with it.. hope it gets moving asap!

actually i just checked again,  he must have got it sorted out because it appears to be on the move now

[desired_username]

I think it would be benefical if we don't pursue this matter further. It's just pointless noise.

Can anyone please confirm the dimensions of the block erupters?

Did you find out the dimensions? i too would like to know before they arrive

Thanks!

That's what I found:

 Hasher size: 233mm x 116mm with a 227mm x 100mm x 19mm heat sink attached to its back      
  Power module size: 192mm x 89mm      
  Ethernet controller size: 86mm x 40mm      

[dogie]

Mine is on a plane from HK to Europe as we speak, but won't be in my hands until Tuesday?! [I called to ask]

All the cabling and wiring ready, I can be up and running in 2 minutes once I have my blades.

[Caesium]

Yeah, they'll land in Germany or something first I guess, move to the UK over the weekend with some luck, but then Bank Holiday on Monday, so Tuesday is the earliest we can hope for.

What number did you call for info, I'll check too

[Noitev]

Mine is on a plane from HK to Europe as we speak, but won't be in my hands until Tuesday?! [I called to ask]

All the cabling and wiring ready, I can be up and running in 2 minutes once I have my blades.

For some awesome reason, I'm getting mine on monday. Strange considering I'm literally as far away from china as you can be...

[radiumsoup]

For some awesome reason, I'm getting mine on monday. Strange considering I'm literally as far away from china as you can be...

Argentina? (The Moon?)

[Noitev]

For some awesome reason, I'm getting mine on monday. Strange considering I'm literally as far away from china as you can be...

Argentina? (The Moon?)

I'd answer, but the light won't reach you until tomorrow.

[bclcjunkie]

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

[dogie]

Yeah, they'll land in Germany or something first I guess, move to the UK over the weekend with some luck, but then Bank Holiday on Monday, so Tuesday is the earliest we can hope for.

What number did you call for info, I'll check too

http://www.dhl.co.uk/en/contact_centre/contact_express.html

[drlatino999]

Mine will be hear monday afternoon, called DHL Customer Service and got my shipping information corrected.

[drlatino999]

Mine will be hear monday afternoon, called DHL Customer Service and got my shipping information corrected.

Damn it, now the world will see I can't choose the correct here/hear.

[michelet]

Mine is on a plane from HK to Europe as we speak, but won't be in my hands until Tuesday?! [I called to ask]

All the cabling and wiring ready, I can be up and running in 2 minutes once I have my blades.

Same to me, they say it will arrive Tuesday. I am in Europe too.

[michelet]

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

[candoo]

Its in germany!

Saturday, May 04, 2013   Location   Time   
12   Customs status updated    LEIPZIG - GERMANY   10:12   
 
11   Departed Facility in HONG KONG - HONG KONG    HONG KONG - HONG KONG   04:34   
 
10   Processed at HONG KONG - HONG KONG    HONG KONG - HONG KONG   04:05   
 
Friday, May 03, 2013   Location   Time   
9   Clearance processing complete at HONG KONG - HONG KONG    HONG KONG - HONG KONG   12:43   
 
8   Processed at HONG KONG - HONG KONG    HONG KONG - HONG KONG   12:43   
 
7   Arrived at Sort Facility HONG KONG - HONG KONG    HONG KONG - HONG KONG   12:38   
 
6   Customs status updated    HONG KONG - HONG KONG   11:05   
 
5   Departed Facility in SHENZHEN - CHINA, PEOPLES REPUBLIC    SHENZHEN - CHINA, PEOPLES REPUBLIC   10:37   
 
4   Processed at SHENZHEN - CHINA, PEOPLES REPUBLIC    SHENZHEN - CHINA, PEOPLES REPUBLIC   10:36   
 
3   Customs status updated    LEIPZIG - GERMANY   04:03   
 
2   Arrived at Sort Facility SHENZHEN - CHINA, PEOPLES REPUBLIC    SHENZHEN - CHINA, PEOPLES REPUBLIC   09:29   
 
Thursday, May 02, 2013   Location   Time   
1   Shipment picked up    SHENZHEN - CHINA, PEOPLES REPUBLIC   21:58   
 

[phiz]

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

Is it really necessary to loop back both terminals like this? I thought friedcat had said these were for chaining boards (ie. are connected already on the PCB). My plan was to use a 6 pin PCIe connector from an ATX PSU and simply twist the three wires together to connect just one +ve and -ve input.

[Pinwheel]

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

Is it really necessary to loop back both terminals like this? I thought friedcat had said these were for chaining boards (ie. are connected already on the PCB). My plan was to use a 6 pin PCIe connector from an ATX PSU and simply twist the three wires together to connect just one +ve and -ve input.

2 wires will work the same, I connected first all 4 points, but now changed to two wires

[bclcjunkie]

awesome! thanks michelet!

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

[bclcjunkie]

pinwheel, has it been working well for you so far? so we just need to use 2 wires right?

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

Is it really necessary to loop back both terminals like this? I thought friedcat had said these were for chaining boards (ie. are connected already on the PCB). My plan was to use a 6 pin PCIe connector from an ATX PSU and simply twist the three wires together to connect just one +ve and -ve input.

2 wires will work the same, I connected first all 4 points, but now changed to two wires

[Noitev]

Is it ironic that each bitcoin I mine with this will be used to buy asicminer shares? lol

[Pinwheel]

pinwheel, has it been working well for you so far? so we just need to use 2 wires right?

Thanks! Appreciate the answer!

hey guys,

can anyone point me in the right direction in terms of electrically wiring this board?

https://docs.google.com/document/d/1VMO3VfIBy3KIwUaaQ8XhKrSVEbXeeMEqsVhhk6Bz9io/edit?pli=1

so the doc says this:

1. The two poles for the positive polarity are identical when cabling from the PSU, so are those for the negative polarity.

i'll be getting myself a psu with 12v/10a output so when i bare the wires, how will i know which wire goes into which hole? the picture below belongs to LainZ and i'm trying to figure out how to wire the board when it arrives...

look at another side of the blade. You will see "+ + - -" marks. So + goes to + and - to -.

Take a look here: https://bitcointalk.org/index.php?topic=178275.msg1928057#msg1928057

Is it really necessary to loop back both terminals like this? I thought friedcat had said these were for chaining boards (ie. are connected already on the PCB). My plan was to use a 6 pin PCIe connector from an ATX PSU and simply twist the three wires together to connect just one +ve and -ve input.

2 wires will work the same, I connected first all 4 points, but now changed to two wires

yes, two wires working perfect, what I have is very strong wires, no any temperature rise have been observed on wires iteself.  I'm mining  and testing it for about a week now. Also fixed 3 USB fans for cooling.  Weather is really hot here. Miining around 10200 mhs on one blade and 9800 mhs on another. Probably will do some overclocking next week. All well, working perfect.

One thing is, it seems miner talking to stratum proxy on http and there is no way to change it, maybe in proxy it self there is some way around, but I doubt that.  It is important task to get ASICminer work with stratum proxy. Perhaps friedcat can bring so clarification.  Most pools moving on stratum now and charging higher comission for those who mine on getwrok servers.