jheaton
|
|
December 27, 2013, 01:02:04 AM |
|
Hi there, I have several chili's, One of the new ones I just received is having issues. When its first plugged in the LED's 5,6,7,8 come on and stay on and never go off.
Any suggestions? Thanks in Advance!~
|
|
|
|
MrTeal (OP)
Legendary
Offline
Activity: 1274
Merit: 1004
|
|
December 27, 2013, 01:52:54 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can.
|
|
|
|
i3luefire
Member
Offline
Activity: 86
Merit: 10
|
|
December 27, 2013, 01:53:29 AM |
|
i may just try and replace the ftdi chip
Before doing that, try shorting the center two pins on the unpopulated 0.1" connector labeled PROG. Pin 5 is MCU reset and pin 6 is ground, so it will hold the microcontroller in reset. If it's an MCU issue holding it in reset should cause the device to pop up on your computer as the FTDI chip will be able to connect. If it doesn't show up, it likely is the FTDI. replacing the FTDI chip fixed it!!!!!!!!
|
|
|
|
MrTeal (OP)
Legendary
Offline
Activity: 1274
Merit: 1004
|
|
December 27, 2013, 01:55:37 AM |
|
My chilis in garage are not working if cold. Yesterday they stopped at 3 am and today same. I rebooted everything and LEDs are blinking well, but my raspberry pi doesn't recognize the devices. They may be gonna recovered Morning as the yesterday case. How are your chilis? Are they okay in -7 Celsius degree?
I found the reason. U25 temperature sensor doesn't work properly under low temperature. I covered it with a small tape and now all chilis are okay. Out of curiosity, how did you verify that the temperature sensor wasn't working correctly? It is specced to work linearly down to -40C, but I haven't actually tested that.
|
|
|
|
joeventura
|
|
December 27, 2013, 01:58:07 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can. Yes second hand. Made a few changes, hopefully it will stabilize
|
|
|
|
lightfoot
Legendary
Offline
Activity: 3122
Merit: 2242
I fix broken miners. And make holes in teeth :-)
|
|
December 27, 2013, 02:10:39 AM |
|
i may just try and replace the ftdi chip
Before doing that, try shorting the center two pins on the unpopulated 0.1" connector labeled PROG. Pin 5 is MCU reset and pin 6 is ground, so it will hold the microcontroller in reset. If it's an MCU issue holding it in reset should cause the device to pop up on your computer as the FTDI chip will be able to connect. If it doesn't show up, it likely is the FTDI. replacing the FTDI chip fixed it!!!!!!!! You rock. I've replaced a few of those on the BFL devices; bitch in heat. How did you do it on the Chili? And what is with those chips? C
|
|
|
|
MrTeal (OP)
Legendary
Offline
Activity: 1274
Merit: 1004
|
|
December 27, 2013, 02:13:44 AM |
|
i may just try and replace the ftdi chip
Before doing that, try shorting the center two pins on the unpopulated 0.1" connector labeled PROG. Pin 5 is MCU reset and pin 6 is ground, so it will hold the microcontroller in reset. If it's an MCU issue holding it in reset should cause the device to pop up on your computer as the FTDI chip will be able to connect. If it doesn't show up, it likely is the FTDI. replacing the FTDI chip fixed it!!!!!!!! You rock. I've replaced a few of those on the BFL devices; bitch in heat. How did you do it on the Chili? And what is with those chips? C It's the first one on a Chili I've heard of failing, but they're actually not that hard to remove. Just heat it with air and pull it off.
|
|
|
|
PhDMiner
Newbie
Offline
Activity: 29
Merit: 0
|
|
December 27, 2013, 02:14:45 AM |
|
My chilis in garage are not working if cold. Yesterday they stopped at 3 am and today same. I rebooted everything and LEDs are blinking well, but my raspberry pi doesn't recognize the devices. They may be gonna recovered Morning as the yesterday case. How are your chilis? Are they okay in -7 Celsius degree?
I found the reason. U25 temperature sensor doesn't work properly under low temperature. I covered it with a small tape and now all chilis are okay. Out of curiosity, how did you verify that the temperature sensor wasn't working correctly? It is specced to work linearly down to -40C, but I haven't actually tested that. Before covering U25, chilis stop soon, but now all fine after covering U25 with a thick tape. Blowing directly to U25 in this freezing cold weather (-7 Celsius degree) might be the reason. Let me check more and will report again.
|
|
|
|
miaviator
Donator
Hero Member
Offline
Activity: 686
Merit: 519
It's for the children!
|
|
December 27, 2013, 02:15:24 AM |
|
Shameless plug? I'm selling my chilis.
|
|
|
|
joeventura
|
|
December 27, 2013, 02:42:11 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can. Yes just the one LED stays on I sent you details and serial number in PM
|
|
|
|
Henchman24
|
|
December 27, 2013, 03:54:01 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can. Yes just the one LED stays on I sent you details and serial number in PM I'm sure this is the miner I just sold joeventura. This is a new symptom. All of my Chilis have performed w/o issue. I've offered to fully refund joeventura if he is unable to get it working. I just want to be clear that this is not a case of me dishing off a problem miner.
|
|
|
|
joeventura
|
|
December 27, 2013, 04:09:08 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can. Yes just the one LED stays on I sent you details and serial number in PM I'm sure this is the miner I just sold joeventura. This is a new symptom. All of my Chilis have performed w/o issue. I've offered to fully refund joeventura if he is unable to get it working. I just want to be clear that this is not a case of me dishing off a problem miner. I am not saying you are doing any such thing. I have no doubt you are an honorable member of the community. I have no worries that if I ask for a refund I will get one.
|
|
|
|
Henchman24
|
|
December 27, 2013, 04:19:41 AM |
|
Just received a Chili today and within minutes of it starting to hash it starts reporting that it is receiving an empty string from the temp sensor and the last Diag LED goes on, its in a 40 degree F room with three fans on it and heat sinks.
Any ideas?
Can I get an RMA?
Just one LED is on, and it just stays on? Was this one you got second hand from someone? PM the serial number and any other details on the symptoms if you can. Yes just the one LED stays on I sent you details and serial number in PM I'm sure this is the miner I just sold joeventura. This is a new symptom. All of my Chilis have performed w/o issue. I've offered to fully refund joeventura if he is unable to get it working. I just want to be clear that this is not a case of me dishing off a problem miner. I am not saying you are doing any such thing. I have no doubt you are an honorable member of the community. I have no worries that if I ask for a refund I will get one. Rats. I was worried that might be misinterpreted. I know you don't think that, joeventura. I just wanted to make sure MrTeal and any third party observers didn't get that impression.
|
|
|
|
i3luefire
Member
Offline
Activity: 86
Merit: 10
|
|
December 27, 2013, 04:36:26 AM |
|
i may just try and replace the ftdi chip
Before doing that, try shorting the center two pins on the unpopulated 0.1" connector labeled PROG. Pin 5 is MCU reset and pin 6 is ground, so it will hold the microcontroller in reset. If it's an MCU issue holding it in reset should cause the device to pop up on your computer as the FTDI chip will be able to connect. If it doesn't show up, it likely is the FTDI. replacing the FTDI chip fixed it!!!!!!!! You rock. I've replaced a few of those on the BFL devices; bitch in heat. How did you do it on the Chili? And what is with those chips? C It's the first one on a Chili I've heard of failing, but they're actually not that hard to remove. Just heat it with air and pull it off. I used an X-acto blade to cut the legs off then cleaned the pads off with solder wick and replaced the chip. no hot air gun available.
|
|
|
|
i3luefire
Member
Offline
Activity: 86
Merit: 10
|
|
December 27, 2013, 04:40:19 AM |
|
The hot air would have been preferable but I have removed plenty of chips this way before so there wasn't much to worry about. The biggest challenge was the large ground plane and my crappy home soldering iron. If I had taken it to work to use the equipment there it would have been much easier but I am on vacation.
|
|
|
|
ZBC3
|
|
December 27, 2013, 06:50:44 AM |
|
Bought 2 boards, one works great 34 ghz, but the other board only has LED's 1-4 come on and is unrecognized by cgminer. PM sent with details.
Thank you MR Teal in advance for your assistance.
|
|
|
|
SosDk
Newbie
Offline
Activity: 24
Merit: 0
|
|
December 27, 2013, 11:59:04 AM |
|
Would like to use the M4x50mm version - but not sure how it will fit. The backplate needs 1 "side" of the screw to be "flat". Are you using a special M4 or am I missing something ?
|
|
|
|
jheaton
|
|
December 27, 2013, 11:03:39 PM |
|
Hi there, I have several chili's, One of the new ones I just received is having issues. When its first plugged in the LED's 5,6,7,8 come on and stay on and never go off.
Any suggestions? Thanks in Advance!~
guess you have to be a Sr. member around here to get a response..
|
|
|
|
miaviator
Donator
Hero Member
Offline
Activity: 686
Merit: 519
It's for the children!
|
|
December 27, 2013, 11:16:06 PM |
|
Hi there, I have several chili's, One of the new ones I just received is having issues. When its first plugged in the LED's 5,6,7,8 come on and stay on and never go off.
Any suggestions? Thanks in Advance!~
guess you have to be a Sr. member around here to get a response.. Or patient. Did you try unplugging, waiting 30 seconds and plugging in again?
|
|
|
|
Hands
Member
Offline
Activity: 67
Merit: 10
|
|
December 27, 2013, 11:30:13 PM |
|
I have a wide range of hardware error rates.. I am wondering if they are related to cooling, luck or random chance... So before I go tearing down my cards and reseating them how do these numbers sound?
1 card at 3.5% error rate, 7 cards around 8% error rate 2 cards at 10% (and change).
So should I be worried with 10% error rates or is this one of those random chance things?
Thanks in advance.
|
|
|
|
|