|
stiffla
|
 |
February 13, 2014, 08:00:53 PM |
|
Set default to hex8 int the web and do not be angry it will work  just a little bit of reading. Post all startup options voltage clock and so on. Fill all blanks in the web cgminer configure using defaults do not leave nothing blank Do not forget to set user pass of tpli k if it is fresh install before that it is not getting any of your setings i left difficulty blank. Now I set it to one and it is working @250GH/s with Frequeny 250 and 980mV. PSU still running stable. Heatsink is not touchable  |
|
|
|
|
marto74 (OP)
|
|
February 13, 2014, 08:03:06 PM |
|
You are the second confirmed HEX8A1 running in the forum.
You can do 260 @ 1050 or 1100 if you are brave.
Please share cg miner screen
|
|
|
|
loshia
Legendary
 Offline
Activity: 1610
Merit: 1000
|
|
February 13, 2014, 08:03:32 PM |
|
Set default to hex8 int the web and do not be angry it will work just a little bit of reading. Post all startup options voltage clock and so on. Fill all blanks in the web cgminer configure using defaults do not leave nothing blank Do not forget to set user pass of tpli k if it is fresh install before that it is not getting any of your setings i left difficulty blank. Now I set it to one and it is working @250GH/s with Frequeny 250 and 980mV. PSU still running stable. Heatsink is not touchable Do not pay attention to it Up to 25 c room temp you are ok. You will get used to hot heatsink. If yo don't like it reduce clock power and hasrate |
|
|
|
|
stiffla
|
|
February 13, 2014, 08:06:17 PM |
|
You are the second confirmed HEX8A1 running in the forum.
You can do 260 @ 1050 or 1100 if you are brave.
Please share cg miner screen
I will do if I will get my stronger PSU tomorrow. what do I have to enter after I am connected to tplink via ssh? |
|
|
|
|
marto74 (OP)
|
|
February 13, 2014, 08:07:22 PM |
|
You are the second confirmed HEX8A1 running in the forum.
You can do 260 @ 1050 or 1100 if you are brave.
Please share cg miner screen
I will do if I will get my stronger PSU tomorrow. what do I have to enter after I am connected to tplink via ssh? user pass screen -r |
|
|
|
|
stiffla
|
|
February 13, 2014, 08:15:16 PM |
|
There you go  One board is still waiting to be set up  |
|
|
|
loshia
Legendary
Offline
Activity: 1610
Merit: 1000
|
|
February 13, 2014, 08:17:37 PM |
|
There you go One board is still waiting to be set up Try one volt 1000 mv and 257 clock |
|
|
|
|
stiffla
|
|
February 13, 2014, 08:19:19 PM |
|
Try one volt 1000 mv and 257 clock
I will give it a try, thx . Friend of mine just started his HEX8A1 board successfull with Odroid |
|
|
|
eiabea
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 13, 2014, 08:28:37 PM |
|
Try one volt 1000 mv and 257 clock
I will give it a try, thx . Friend of mine just started his HEX8A1 board successfull with Odroid yes it works, but it is just a matter of time when my neighbors call the police or my girlfriend kicks me out. this device is ridiculous loud!!  |
|
|
|
|
|
marto74 (OP)
|
|
February 13, 2014, 08:34:03 PM |
|
|
|
|
|
|
Gator-hex
|
|
February 13, 2014, 08:48:42 PM |
|
Can a TP-Link run both Hex16B and Hex8A1 at the same time? Which do u set as default then?
|
|
|
|
|
Gator-hex
|
|
February 13, 2014, 09:05:30 PM
Last edit: February 13, 2014, 09:17:04 PM by Gator-hex |
|
Can a TP-Link run both Hex16B and Hex8A1 at the same time? Which do u set as default then? That one Fan on the top is EXTREMELY noisy yes it works, but it is just a matter of time when my neighbors call the police or my girlfriend kicks me out. this device is ridiculous loud!! Beastlymac and dozerz are looking to buy if anyone hates the noise! I did warn you about Sunon Maglev 4500rpm. Did you get finger guards? If not, be very careful, these are industrial strength fans, can take the end off your fingers! I'm gonna replace the fans and run it at a lower clock, if mine ever arrive. What are good settings for 200GH? Will these A1 run at 1GH/1W there like Bitmine's A1? |
|
|
|
|
marto74 (OP)
|
|
February 13, 2014, 09:22:59 PM |
|
Gator
@ 200 you can run 850 mV stbale if HW more than 2 % for 1/2 hour rise voltage a bit
the you can use some 2500-3000 W fans
|
|
|
|
|
stiffla
|
|
February 13, 2014, 10:15:35 PM |
|
Try one volt 1000 mv and 257 clock
I will give it a try, thx . Friend of mine just started his HEX8A1 board successfull with Odroid This settings are not working after ~10min, but I guess it depends on my current PSU. I was wondering about putting a slower fan on the top of the miner and two 120mm on the sides to get an air stream. What do you guys think about this? I guess it would be much more silent than my curretn 80db |
|
|
|
|
Gator-hex
|
|
February 13, 2014, 10:28:55 PM |
|
Try one volt 1000 mv and 257 clock
I will give it a try, thx . Friend of mine just started his HEX8A1 board successfull with Odroid This settings are not working after ~10min, but I guess it depends on my current PSU. I was wondering about putting a slower fan on the top of the miner and two 120mm on the sides to get an air stream. What do you guys think about this? I guess it would be much more silent than my curretn 80db Where the heatsinks aligned like this = or this +? If they were like this = I was going to build a wind tunnel and put a 120mm fan at one end and blow air over both heatsinks. But last I saw Marto changed the heatsink design to +. For that configuration I was going to put 2x 43cfm 92mm fans on top with cable ties. |
|
|
|
|
|
|
Gator-hex
|
|
February 13, 2014, 10:34:01 PM
Last edit: February 13, 2014, 10:56:00 PM by Gator-hex |
|
Oh no! Please don't give Marto & Zich any suggestions for stronger fans! They'll use them! GH to the moon, just needs faster fans!  Shhh! Don't mention the Delta 92mm/4800rpm/110cfm! |
|
|
|
|
stiffla
|
|
February 13, 2014, 10:54:10 PM |
|
Where the heatsinks aligned like this = or this +?
If they were like this = I was going to build a wind tunnel and put a 120mm fan at one end and blow air over both heatsinks.
But last I saw Marto changed the heatsink design to +. For that configuration I was going to put 2x 43cfm 92mm fans on top with cable ties.
The heatsink is like this  |
|
|
|
|
Gator-hex
|
|
February 13, 2014, 11:00:11 PM |
|
Where the heatsinks aligned like this = or this +?
If they were like this = I was going to build a wind tunnel and put a 120mm fan at one end and blow air over both heatsinks.
But last I saw Marto changed the heatsink design to +. For that configuration I was going to put 2x 43cfm 92mm fans on top with cable ties.
The heatsink is like this Yeah the heatsink air flows are in a cross + so you cannot use a wind tunnel to cover both heatsinks with a big fan. Can you measure the length of the heatsink and see if it's 184mm long. 2x 92mm fans on the top was my next idea, depends on length of heatsink though. |
|
|
|
|
stiffla
|
|
February 13, 2014, 11:05:22 PM |
|
Yeah the heatsink air flows are in a cross + so you cannot use a wind tunnel to cover both heatsinks with a big fan.
Can you measure the length of the heatsink and see if it's 184mm long.
2x 92mm fans on the top was my next idea, depends on length of heatsink though.
yeah heatsink is 183mm long, both fans are 92mm |
|
|
|
|
