[ANN] Technobit HEX8A1 -240 GHs Coincraft A1 board- Finished production

[gcube1305]

0.3.1 Milestone release http://technobit.eu/0_3_1.rar

Hello Martin,
Link down, is the 0.3.1 version available or is this a typo error ?
0.3.0 is available.

Try this http://technobit.eu/0_3_1.rar

Great thanks.

[gcube1305]

Is this update "mandatory"?
I mean my hex8 is working perfectly (more than 1 month now, no reboot at all, with default settings 260@1000 and almost no HW error), what will i gain with this update?

[loshia]

Is this update "mandatory"?
I mean my hex8 is working perfectly (more than 1 month now, no reboot at all, with default settings 260@1000 and almost no HW error), what will i gain with this update?

No tplink speed degradation over time

But the golden rule always is if it works do not touch it

[Lucko]

Hi marto74!

See you are working as always... Any news on my Repair/Replacement HEX8?

Regards

[Lucko]

0.3.0 Milestone release http://technobit.eu/0_3_0.rar
- GET WORK cgminer support is depreciated. !!!USE STRATUM ONLY!!!!
* cgminer patch to cgminer 4.2.1 rev df7dcab4677a9fea1e1b7ac7b756d72e2e9c6f46.patch
* cgminer bug fixes: thread locking, memleaks, stage work buffer length adjustments and many more. All hex drivers were rewritten
* cgminer the most stable release! We encourage all to upgrade!
* openwrt updated to r40295

- GET WORK cgminer support is depreciated. !!!USE STRATUM ONLY!!!!

Well I still use GET WORK... I run BFGminer in with get work virtual devices so I have all mining on one device... And can see at once if anything is wrong... Was that done by you or cgminer team? I don't see anything at new cgminer announcement

[HellDiverUK]

cgminer abandoned getwork, same way they pulled the plug on GPU mining.

[Zich]

Where would you use getwork today?

DeepBit is still getwork only ... almost dead, because of that.

Ah yes, out of sight, out of mind because of it too. I wasn't even sure there was anywhere I could even test it to fix it.

Okay, fixed it in git.

[glen123]

Hi !

@Marto :

can you pls check your PM ?

The Tracking Number for
Order :QSUFGPQFI    2014-03-06       PD PayPal + Extra Fee    Shipped

Track : 60084825146

not work .

Greetz Glen

[iFA88]

Sadly today my Hex8 260 mhash stopped hashing. The bottom fan has stopped working, and i believe the chips are burned out. On the board is nothing bad to see, all is well.
The PSU give 12+ volt up, the board LED's (orange and green) lights all time. I have tryed other USB port, but no ones help. The RED lead dont glow up at all.
The devide should have to mine 1.5 more BTC.. but now its full loss! I payed for that 1545EUR. i would like a fully support for that.
Some API stats:

Code:

---------------
Chip3 Nonces: 0
Chip6 Dupes: 0
Chip8 Dupes: 0
Last Share Time: 0
Chip4 Nonces: 0
USB Reset Count: 0
Chip5 Engines: 0
Chip2 Engines: 0
Chip4 Dupes: 0
Status: Alive
Chip3 Engines: 0
Chip7 Engines: 0
Chip8 Engines: 0
Chip6 Engines: 0
Chip8 Nonces: 0
Elapsed: 670
Hardware Errors: 0
Chip5 Dupes: 0
Chip Count: 8
Chip1 Nonces: 0
Chip7 Dupes: 0
Hardware Errors%: 0.0
Core Voltage: 1000
STATS: 6
Chip7 Nonces: 0
Enabled: Y
Chip1 Engines: 0
Chip1 Dupes: 0
PIC Voltage Readings: 800
ID: HEX80
Chip6 Nonces: 0
MHS av: 0.000
Chip5 Nonces: 0
MHS 5s: 0.000
Chip3 Dupes: 0
USB Write Errors: 0
Chip2 Dupes: 0
USB Read Errors: 0
Chip4 Engines: 0
Frequency: 260
Chip2 Nonces: 0
---------------

I have repoerted on the site too. (RMA)

[loshia]

Sadly today my Hex8 260 mhash stopped hashing. The bottom fan has stopped working, and i believe the chips are burned out. On the board is nothing bad to see, all is well.
The PSU give 12+ volt up, the board LED's (orange and green) lights all time. I have tryed other USB port, but no ones help. The RED lead dont glow up at all.
The devide should have to mine 1.5 more BTC.. but now its full loss! I payed for that 1545EUR. i would like a fully support for that.
Some API stats:

Code:

---------------
Chip3 Nonces: 0
Chip6 Dupes: 0
Chip8 Dupes: 0
Last Share Time: 0
Chip4 Nonces: 0
USB Reset Count: 0
Chip5 Engines: 0
Chip2 Engines: 0
Chip4 Dupes: 0
Status: Alive
Chip3 Engines: 0
Chip7 Engines: 0
Chip8 Engines: 0
Chip6 Engines: 0
Chip8 Nonces: 0
Elapsed: 670
Hardware Errors: 0
Chip5 Dupes: 0
Chip Count: 8
Chip1 Nonces: 0
Chip7 Dupes: 0
Hardware Errors%: 0.0
Core Voltage: 1000
STATS: 6
Chip7 Nonces: 0
Enabled: Y
Chip1 Engines: 0
Chip1 Dupes: 0
PIC Voltage Readings: 800
ID: HEX80
Chip6 Nonces: 0
MHS av: 0.000
Chip5 Nonces: 0
MHS 5s: 0.000
Chip3 Dupes: 0
USB Write Errors: 0
Chip2 Dupes: 0
USB Read Errors: 0
Chip4 Engines: 0
Frequency: 260
Chip2 Nonces: 0
---------------

I have repoerted on the site too. (RMA)

Give it some time to rest 2-3 min without power
Then see if chips will be back?
Not much but this is only thing i can suggest

[iFA88]

Give it some time to rest 2-3 min without power
Then see if chips will be back?
Not much but this is only thing i can suggest

I have tryed soon, i have replaced to a other FAN in the bottom. The heat sink was cold.

[Gator-hex]

Give it some time to rest 2-3 min without power
Then see if chips will be back?
Not much but this is only thing i can suggest

I have tryed soon, i have replaced to a other FAN in the bottom. The heat sink was cold.

If it has polyfuses (those brown tags that stick out) it might take more than few minutes I'd leave it unplugged overnight (some pop it in the fridge).
http://en.wikipedia.org/wiki/Resettable_fuse

Your power supply probably went into emergency shutdown too. That usually requires the paper clip to be removed to reset that.
Some PSUs require something powered on the 5v line to stop them tripping into emergency mode. My ThermalTake 730W did.

Marto never said what the orange LED means, but I suspect it's a polyfuse error, my Hex8A1 with 2 detached polyfuses has orange LED, but still mines.

[ZBC3]

Glen123

Try this link;

http://www.speedy.bg/begin.php?nccharset=08F9FDFC&shipmentNumber=60084825146&lang=en&__ncforminfo=G9NcZtEOEt6Y3yJpGNGZQd3s88mBrJnrGsc1xj_dxeLGXCs2Pe6RSUH61V6ff7LIU9dooPTQrR9FyFlsGfPQPz5h-Ij_n4I0L1QlYEK3Pkc%3D

Usually it goes from Speedy to another courier depending on what country you live in. You can email speedy and they will tell you the new couriers tracking number.


Update:

Speedy shows the new tracking number is from DPD, 16602410119468.

http://www.dpd.com/tracking

[iFA88]

Thanks for the tip, i would test the polyfuses!

Give it some time to rest 2-3 min without power
Then see if chips will be back?
Not much but this is only thing i can suggest

I have tryed soon, i have replaced to a other FAN in the bottom. The heat sink was cold.

If it has polyfuses (those brown tags that stick out) it might take more than few minutes I'd leave it unplugged overnight (some pop it in the fridge).
http://en.wikipedia.org/wiki/Resettable_fuse

Your power supply probably went into emergency shutdown too. That usually requires the paper clip to be removed to reset that.

Marto never said what the orange LED means, but I suspect it's a polyfuse error, my Hex8A1 with 2 detached polyfuses has orange LED, but mines.

[iFA88]

I have tested all polyfuses and all working, no one is defected. The PSU give the 12 volt i have messed with multimeter. The 2 fans work too normaly. The board simple not hashing.

Give it some time to rest 2-3 min without power
Then see if chips will be back?
Not much but this is only thing i can suggest

I have tryed soon, i have replaced to a other FAN in the bottom. The heat sink was cold.

If it has polyfuses (those brown tags that stick out) it might take more than few minutes I'd leave it unplugged overnight (some pop it in the fridge).
http://en.wikipedia.org/wiki/Resettable_fuse

Your power supply probably went into emergency shutdown too. That usually requires the paper clip to be removed to reset that.
Some PSUs require something powered on the 5v line to stop them tripping into emergency mode. My ThermalTake 730W did.

Marto never said what the orange LED means, but I suspect it's a polyfuse error, my Hex8A1 with 2 detached polyfuses has orange LED, but still mines.

[glen123]

Glen123

Try this link;

http://www.speedy.bg/begin.php?nccharset=08F9FDFC&shipmentNumber=60084825146&lang=en&__ncforminfo=G9NcZtEOEt6Y3yJpGNGZQd3s88mBrJnrGsc1xj_dxeLGXCs2Pe6RSUH61V6ff7LIU9dooPTQrR9FyFlsGfPQPz5h-Ij_n4I0L1QlYEK3Pkc%3D

Usually it goes from Speedy to another courier depending on what country you live in. You can email speedy and they will tell you the new couriers tracking number.


Update:

Speedy shows the new tracking number is from DPD, 16602410119468.

http://www.dpd.com/tracking

Wow , thank You for Help !
Seems to be a good Birthday Present ( 03.04 ) for me when its delivered ;-)

Glen

[iFA88]

The hex8 is still not working. Why work these RMA? Where should i post the item? How many time need to replace/repair ? Every day its a deficit for me..

[Lucko]

You send it Technobit. My unit is there now for a week. And as far as I know they are shipping it back to me today...

[Gator-hex]

The hex8 is still not working. Why work these RMA? Where should i post the item? How many time need to replace/repair ? Every day its a deficit for me..

"Make this as a regular order and choose  Bank wire payment @ the end The you'll get shiping address for your broken unit to be delivered to"

http://technobit.eu/index.php?id_category=14&controller=category&id_lang=1

[glen123]

 

HEX was delivered today ;-)))))))))))))

Thx all for your Help .

under Windows its Worked , now i worked with the PI ( Minepeon ) . Its starts , but no Hashrate . Hardware found and show under cgminer  !

Greetz Glen

Edit :
Can anybody help ?

0: HEX8 0       : 200  800/ 800mV         | A:0 R:0/0.00% HW:0/0.00% WU:0.0/m
--------------------------------------------------------------------------------
 [2014-04-02 18:10:00] Started cgminer 4.2.2
 [2014-04-02 18:10:00] Loaded configuration file /opt/minepeon/etc/miner.conf
 [2014-04-02 18:10:01] Probing for an alive pool
 [2014-04-02 18:10:01] Pool 0 difficulty changed to 16
 [2014-04-02 18:10:01] Pool 1 difficulty changed to 32
 [2014-04-02 18:10:02] Network diff set to 96.6M
 [2014-04-02 18:10:07] API running in IP access mode on port 4028 (11)

MinePeon Version
    0.2.4.6
Miner Version
    cgminer4.2.2  updatet fromthis thread

stratum+tcp://peercoin.ecoining.com:3336

Edit 2:
 [2014-04-02 18:33:33] Discarded work
 [2014-04-02 18:33:33] (5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s
 [2014-04-02 18:33:33] Selecting pool 0 for work
 [2014-04-02 18:33:33] Generated stratum merkle 3f7effb66b2cd994311914cadad3424c2bac50423279f01661a083c71eff0984
 [2014-04-02 18:33:33] Generated stratum header 000000012894832a6b02071ebe4875a45ae7c05c48dd5547f94a95f7633ba8b2eaf4e8283f7effb 66b2cd994311914cadad3424c2bac5
0423279f01661a083c71eff0984533c57f9192c705a000000000000008000000000000000000000 000000000000000000000000000000000000
 [2014-04-02 18:33:33] Work job_id a441 nonce2 89 ntime 533c57f9
 [2014-04-02 18:33:33] Generated target 00000000000000000000000000000000000000000000000000f0ff0f00000000
 [2014-04-02 18:33:33] Generated stratum work
 [2014-04-02 18:33:33] Pushing work from pool 0 to hash queue
 [2014-04-02 18:33:33] [thread 0: 0 hashes, 0.0 mhash/sec]
 [2014-04-02 18:33:35] Discarded work
 [2014-04-02 18:33:35] Selecting pool 0 for work
 [2014-04-02 18:33:35] Generated stratum merkle e784e75f1522945a26ee320479f549a306b80dd3ab88053c9976621e5a5a22c7
 [2014-04-02 18:33:35] Generated stratum header 000000012894832a6b02071ebe4875a45ae7c05c48dd5547f94a95f7633ba8b2eaf4e828e784e75 f1522945a26ee320479f549a306b80
dd3ab88053c9976621e5a5a22c7533c57f9192c705a000000000000008000000000000000000000 000000000000000000000000000000000000
 [2014-04-02 18:33:35] Work job_id a441 nonce2 90 ntime 533c57f9
 [2014-04-02 18:33:35] Generated target 00000000000000000000000000000000000000000000000000f0ff0f00000000
 [2014-04-02 18:33:35] Generated stratum work
 [2014-04-02 18:33:35] Pushing work from pool 0 to hash queue
 [2014-04-02 18:33:37] USB scan devices: checking for HEXa devices
 [2014-04-02 18:33:37] HEXa looking for HEXa 04d8:000a but found 05e3:0608 instead
 [2014-04-02 18:33:37] HEXa looking for and found HEXa 04d8:000a
 [2014-04-02 18:33:37] HEXa looking for HEXa 04d8:000a but found 05e3:0608 instead
 [2014-04-02 18:33:37] HEXa looking for HEXa 04d8:000a but found 0424:ec00 instead
 [2014-04-02 18:33:37] HEXa looking for HEXa 04d8:000a but found 0424:9512 instead
 [2014-04-02 18:33:37] HEXa looking for HEXa 04d8:000a but found 1d6b:0002 instead
 [2014-04-02 18:33:37] USB scan devices: checking for HEXb devices


Any suggestions ?

Glen