[ANN] QQCoin- Scrypt Jane, ASIC Resistant, N-Factor, Multipool Resistant

[haggis]

Thank you! But it seems not helpful for my case. I tried all low/mid/high combinations of TC between 8192 and 32768 with lookup-gap between 2 and 8 while rawintensity was < 1000 

As I use BAMT which is 32 Bit only 2GB of 8GB are available. When I find some spare time I'll setup a 64Bit system and see if that works better for scrypt-jane

[lumberinvestments]

Thank you! But it seems not helpful for my case. I tried all low/mid/high combinations of TC between 8192 and 32768 with lookup-gap between 2 and 8 while rawintensity was < 1000 

As I use BAMT which is 32 Bit only 2GB of 8GB are available. When I find some spare time I'll setup a 64Bit system and see if that works better for scrypt-jane

Just throw in a 64 bit system.. 2 GB are never enough for scrypt-jane at higher N. You can try though TC of 4096 or 2048 to see which one is working. Raw intensity 1024/2048/4096 at lg 3 or higher. Then you just increase the TC until it will not start anymore. Then you go higher with R in increments of w (if w is 128 just add 128 each time).

[lenovothinkpad]

i7=150khs
955=100Khs
use the CPU mine
These are only rough mining specs.

when you look here ↗Welcome to the QQC community

[lumberinvestments]

i7=150khs
955=100Khs
use the CPU mine
These are only rough mining specs.

when you look here ↗Welcome to the QQC community

I think you are wrong. More like 10-15 kh/sec for that CPU as of now, not 150 kh/sec

[lenovothinkpad]

i7=150khs
955=100Khs
use the CPU mine
These are only rough mining specs.

when you look here ↗Welcome to the QQC community

I think you are wrong. More like 10-15 kh/sec for that CPU as of now, not 150 kh/sec

10-15 ?  my cpu is AMD 955 so I went to give it a try

[Nicho]

Does this coin have any active developers, community or founding?

[lumberinvestments]

Community is in China.
Heard pumping is coming soon, everybody should buy this coin as it is still so much undervalued, take a look at what happened to VTC.

[infofront]

I just tried buying more on coinedup and it says trading has been temporarily halted on this market. 

[cryptohunter]

I just tried buying more on coinedup and it says trading has been temporarily halted on this market. 

same, we need another exchange, get voting on mintpal everyone.... you can vote 3x per hour and don't even need to be registered there. Tell your friends to also.

[lenovothinkpad]

community also can join the development ,as coding as you can 

[lenovothinkpad]

news: allcrypt  exChange https://www.allcrypt.com accept QQC/BTC QQC/LTC QQC/DOGE
A new web site ,about this exchange We are still in the query details.

[trid]

I just tried buying more on coinedup and it says trading has been temporarily halted on this market. 

same, we need another exchange, get voting on mintpal everyone.... you can vote 3x per hour and don't even need to be registered there. Tell your friends to also.

qqc on https://www.allcoin.com/trade/qqc_btc too

[lumberinvestments]

Can you just stop dumping .. whoever mines big amount ??
This coin needs to go high. If you never stop dumping you will never see it high !

[Dopehaze]

Thank you! But it seems not helpful for my case. I tried all low/mid/high combinations of TC between 8192 and 32768 with lookup-gap between 2 and 8 while rawintensity was < 1000 

As I use BAMT which is 32 Bit only 2GB of 8GB are available. When I find some spare time I'll setup a 64Bit system and see if that works better for scrypt-jane

Just throw in a 64 bit system.. 2 GB are never enough for scrypt-jane at higher N. You can try though TC of 4096 or 2048 to see which one is working. Raw intensity 1024/2048/4096 at lg 3 or higher. Then you just increase the TC until it will not start anymore. Then you go higher with R in increments of w (if w is 128 just add 128 each time).

You don't need much system RAM on Linux, 256-512MB should be enough if you are running some lite distribution such as Lubuntu. Windows drivers have a bug, it queries amount of system RAM instead of VRAM.

Below are my settings for 280X, about 135khs per card.

Code:

"intensity" : "12,12,12,12",
"vectors" : "1,1,1,1",
"worksize" : "256,256,256,256",
"kernel" : "scrypt-jane,scrypt-jane,scrypt-jane,scrypt-jane",
"lookup-gap" : "0,0,0,0",
"thread-concurrency" : "16384,16384,16384,16384",
"shaders" : "0,0,0,0",
"gpu-engine" : "0-1050,0-1050,0-1050,0-1050",
"gpu-fan" : "0-85,0-85,0-85,0-85",
"gpu-memclock" : "0,0,0,0",
"gpu-memdiff" : "0,0,0,0",
"gpu-powertune" : "0,0,0,0",
"gpu-vddc" : "0.000,0.000,0.000,0.000",
"temp-cutoff" : "95,95,95,95",
"temp-overheat" : "85,85,85,85",
"temp-target" : "75,75,75,75",
"gpu-reorder" : true,
"api-mcast-port" : "4028",
"api-port" : "4028",
"auto-fan" : true,
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "2",
"gpu-reorder" : true,
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "60",
"scrypt" : true,
"scrypt-jane" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"

[lumberinvestments]

Thank you! But it seems not helpful for my case. I tried all low/mid/high combinations of TC between 8192 and 32768 with lookup-gap between 2 and 8 while rawintensity was < 1000 

As I use BAMT which is 32 Bit only 2GB of 8GB are available. When I find some spare time I'll setup a 64Bit system and see if that works better for scrypt-jane

Just throw in a 64 bit system.. 2 GB are never enough for scrypt-jane at higher N. You can try though TC of 4096 or 2048 to see which one is working. Raw intensity 1024/2048/4096 at lg 3 or higher. Then you just increase the TC until it will not start anymore. Then you go higher with R in increments of w (if w is 128 just add 128 each time).

You don't need much system RAM on Linux, 256-512MB should be enough if you are running some lite distribution such as Lubuntu. Windows drivers have a bug, it queries amount of system RAM instead of VRAM.

Below are my settings for 280X, about 135khs per card.

Code:

"intensity" : "12,12,12,12",
"vectors" : "1,1,1,1",
"worksize" : "256,256,256,256",
"kernel" : "scrypt-jane,scrypt-jane,scrypt-jane,scrypt-jane",
"lookup-gap" : "0,0,0,0",
"thread-concurrency" : "16384,16384,16384,16384",
"shaders" : "0,0,0,0",
"gpu-engine" : "0-1050,0-1050,0-1050,0-1050",
"gpu-fan" : "0-85,0-85,0-85,0-85",
"gpu-memclock" : "0,0,0,0",
"gpu-memdiff" : "0,0,0,0",
"gpu-powertune" : "0,0,0,0",
"gpu-vddc" : "0.000,0.000,0.000,0.000",
"temp-cutoff" : "95,95,95,95",
"temp-overheat" : "85,85,85,85",
"temp-target" : "75,75,75,75",
"gpu-reorder" : true,
"api-mcast-port" : "4028",
"api-port" : "4028",
"auto-fan" : true,
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "2",
"gpu-reorder" : true,
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "60",
"scrypt" : true,
"scrypt-jane" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"

Are you getting no hardware errors with that ?

[cryptohunter]

i don't think people realise how rare 30M minting is.  The price for this coin is below value for a no premine coin which is this fast. I have liked it from the start. If a billion new coins a day were not coming out qqc will do way better.

[Dopehaze]

Thank you! But it seems not helpful for my case. I tried all low/mid/high combinations of TC between 8192 and 32768 with lookup-gap between 2 and 8 while rawintensity was < 1000 

As I use BAMT which is 32 Bit only 2GB of 8GB are available. When I find some spare time I'll setup a 64Bit system and see if that works better for scrypt-jane

Just throw in a 64 bit system.. 2 GB are never enough for scrypt-jane at higher N. You can try though TC of 4096 or 2048 to see which one is working. Raw intensity 1024/2048/4096 at lg 3 or higher. Then you just increase the TC until it will not start anymore. Then you go higher with R in increments of w (if w is 128 just add 128 each time).

You don't need much system RAM on Linux, 256-512MB should be enough if you are running some lite distribution such as Lubuntu. Windows drivers have a bug, it queries amount of system RAM instead of VRAM.

Below are my settings for 280X, about 135khs per card.

Code:

"intensity" : "12,12,12,12",
"vectors" : "1,1,1,1",
"worksize" : "256,256,256,256",
"kernel" : "scrypt-jane,scrypt-jane,scrypt-jane,scrypt-jane",
"lookup-gap" : "0,0,0,0",
"thread-concurrency" : "16384,16384,16384,16384",
"shaders" : "0,0,0,0",
"gpu-engine" : "0-1050,0-1050,0-1050,0-1050",
"gpu-fan" : "0-85,0-85,0-85,0-85",
"gpu-memclock" : "0,0,0,0",
"gpu-memdiff" : "0,0,0,0",
"gpu-powertune" : "0,0,0,0",
"gpu-vddc" : "0.000,0.000,0.000,0.000",
"temp-cutoff" : "95,95,95,95",
"temp-overheat" : "85,85,85,85",
"temp-target" : "75,75,75,75",
"gpu-reorder" : true,
"api-mcast-port" : "4028",
"api-port" : "4028",
"auto-fan" : true,
"expiry" : "120",
"gpu-dyninterval" : "7",
"gpu-platform" : "0",
"gpu-threads" : "2",
"gpu-reorder" : true,
"log" : "5",
"no-pool-disable" : true,
"queue" : "1",
"scan-time" : "60",
"scrypt" : true,
"scrypt-jane" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"kernel-path" : "/usr/local/bin"

Are you getting no hardware errors with that ?

No HW errors on 4 Gigabyte and 4 Powercolor cards.

[KickAzzDude]

Need to get it on a bigger exchange, the current market cap for this coin is insanely low. We need to promote it more, how's the Chinese support coming? This is a great coin with N-Factor way before it started getting popular which means no multipool has mined and dumped it

[lumberinvestments]

Everyone, please vote QQC on mintpal.com at https://www.mintpal.com/voting
You can vote every hour, if we do this for sure the value of QQCoin will increase !

[ashao1015]

Voted for QQC.
We need a better exchange, the value of QQCoin will increase!