toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
April 28, 2017, 07:23:51 PM Last edit: May 10, 2017, 09:36:03 AM by toptek |
|
Hey Mich Ive been having some issue with my Alchemist, I wasn't before with minera ... i had to go to directly using BFG @ the black screen using SSH without minera .. it sometimes take me hours after i turn the miner off for a few days because of it's power usage, i have to watch it some it still pays good but i can't use it as much and run my A4 tube all most 24/7 but sadly that PI won't install minera and there is no way i can get it boot from a new SD image , I tried to manually install it .INNOSILICON uses closed software .... and users a old raspberry PI model with there A4's and a board that plugs into the PI that interacts with those model PI and miner ..... or actually controls it all ...that only boots with there software and fork of CGMNIER. what's happen with the Alchemist is i turn on the miner first, let it run 2 mins then turn on the PI minera is on .. and it won't all ways pick up all the boards right a way ,like it used to, unless I unplug everything a few times then plug it back in and tune it off and on a few more times. i tried different PSU's all kinds of others stuff, then I tried it with BFG direct using SSH and all five boards come to life in one try everytime .... like they used with minera ... just a heads up ... MY bad it's not minera like i thought, it's the OS for some reason https://www.armbian.com/ OS's stop running lighttpd after a reboot ... they have a major update coming out in a few days , till then i have to use it at the black BFG screen Direct. or use my RPI 3 custom install it works with RPI2 and 3 with Ubuntu 16...
|
|
|
|
michelem (OP)
Legendary
Offline
Activity: 1015
Merit: 1000
|
|
April 29, 2017, 07:59:08 AM |
|
What I mean is, even though it's installed when I go to localhost/minera I get an unable to connect page. Never prompted for a password. Currently searching for a HDMI cable so I can see what my Pis IP address, installed the image on there since the one on my Xubuntu install isnt functional.
Please explain where you installed it. Isn't it a raspberry? Did you install it manually without the SD card image?
|
|
|
|
jahwillprovide
Member
Offline
Activity: 70
Merit: 10
|
|
May 01, 2017, 04:04:35 AM |
|
What I mean is, even though it's installed when I go to localhost/minera I get an unable to connect page. Never prompted for a password. Currently searching for a HDMI cable so I can see what my Pis IP address, installed the image on there since the one on my Xubuntu install isnt functional.
Please explain where you installed it. Isn't it a raspberry? Did you install it manually without the SD card image? I installed it on my main work computer and couldn't access it thru it's web app on the same computer. I'll update when I go to work tomorrow, gonna build out 2 more racks loaded with 2650s. Eventually I'll need management software.
|
|
|
|
giantkin
|
|
May 01, 2017, 01:45:19 PM |
|
What I mean is, even though it's installed when I go to localhost/minera I get an unable to connect page. Never prompted for a password. Currently searching for a HDMI cable so I can see what my Pis IP address, installed the image on there since the one on my Xubuntu install isnt functional.
Please explain where you installed it. Isn't it a raspberry? Did you install it manually without the SD card image? I installed it on my main work computer and couldn't access it thru it's web app on the same computer. I'll update when I go to work tomorrow, gonna build out 2 more racks loaded with 2650s. Eventually I'll need management software. I have 60 or 70 HDMI cables in a box here... doesnt do you much good tho! lol. I keep meaning to list them on Amazon...one of these days ill remember. maybe. (probably not) its funny, never thought i would use as many as i got...but i keep taking another one out of the box. g
|
http://choicehost.biz Domains and DIY -hosting I save $5 or so, for each domain a year. (Compared to other Domain Registrars)
|
|
|
deni3en
Newbie
Offline
Activity: 1
Merit: 0
|
|
May 02, 2017, 07:43:28 AM |
|
Hi guys! I have some Antminer s9 hardware, can i monitor them with minera? Cant find solution for this
|
|
|
|
michelem (OP)
Legendary
Offline
Activity: 1015
Merit: 1000
|
|
May 02, 2017, 07:44:46 AM |
|
Hi guys! I have some Antminer s9 hardware, can i monitor them with minera? Cant find solution for this
You have to change the default miner with Cgminer. Here someone did something https://bitcointalk.org/index.php?topic=1569129.0
|
|
|
|
Trophonius
Newbie
Offline
Activity: 40
Merit: 0
|
|
May 05, 2017, 11:51:28 PM |
|
This actually is a great dashboard. I've been using it for a few hours now and it's working great. Sometimes I feel like it walks a but behind the actual stuff that's happening. Like that it has some kind of delay.
Probably just my own internet and it doesn't really bother me.
I hope that I can use this a lot more for a long time!
Thanks.
|
|
|
|
tukangkopi
|
|
May 07, 2017, 07:56:02 AM |
|
Sounds similar to my issue with the blades.. I issue freq settings but only one chip per in each array use that speed. the others all fall to the default 600. i was seeing it when running directly from command lien so I dont think its related to Minera.
|
|
|
|
jccoro
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 14, 2017, 02:34:04 AM |
|
Hi to all. Hope you can help me guys. I just install Minera few days ago. First on Mining Profitability shows old info and im not able to remove it. If im mining any crypto scrypt coin its not show it on the list.
Other issue that happend today is that i was hashing with a gridseed g-blade 40chips. and the cgminer continously restarts and on dashboard shows in errors/rejects NaN%. I been using gridseed for 3 days without a problem. The log doesnt show any error. just restart the cgminer around every 30 to 40 seconds.
Thanks
|
|
|
|
michelem (OP)
Legendary
Offline
Activity: 1015
Merit: 1000
|
|
May 14, 2017, 05:29:33 AM |
|
Hi to all. Hope you can help me guys. I just install Minera few days ago. First on Mining Profitability shows old info and im not able to remove it. If im mining any crypto scrypt coin its not show it on the list.
Other issue that happend today is that i was hashing with a gridseed g-blade 40chips. and the cgminer continously restarts and on dashboard shows in errors/rejects NaN%. I been using gridseed for 3 days without a problem. The log doesnt show any error. just restart the cgminer around every 30 to 40 seconds.
Thanks
Hello and welcome to Minera, first of all Mining Profitability panel has "fixed" data that only me can change from the server. So that's normal. For the blade problem, try to change the pool and if possible give us the cgminer log.
|
|
|
|
jccoro
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 15, 2017, 12:37:36 AM |
|
Michelem thanks for your help. I reinstall the cgminer and reset the minera and everything goes normal again. At the end y dont know what happend.
On the mining profitability i dont undestand what you say about fixed values. If im mining novacoins it not going to be show on that widget in the dashboard?
Thanks
|
|
|
|
michelem (OP)
Legendary
Offline
Activity: 1015
Merit: 1000
|
|
May 15, 2017, 06:00:29 AM |
|
Michelem thanks for your help. I reinstall the cgminer and reset the minera and everything goes normal again. At the end y dont know what happend.
On the mining profitability i dont undestand what you say about fixed values. If im mining novacoins it not going to be show on that widget in the dashboard?
Thanks
No. It displays only Litecoin and Bitcoin by now and it's not connected to what you are mining. May be in the future....
|
|
|
|
MaximC
Jr. Member
Offline
Activity: 42
Merit: 2
|
|
May 25, 2017, 10:45:51 AM |
|
|
|
|
|
michelem (OP)
Legendary
Offline
Activity: 1015
Merit: 1000
|
|
May 25, 2017, 12:09:28 PM |
|
Claymore isn't supported by lack of API. L3+ isn't out yet but I don't think it will have the requirements.
|
|
|
|
MaximC
Jr. Member
Offline
Activity: 42
Merit: 2
|
|
May 25, 2017, 12:13:31 PM |
|
Claymore isn't supported by lack of API. L3+ isn't out yet but I don't think it will have the requirements. We plan do some L3+ and GPU mining (thinking about two currencies mine - in this case Claymore). But is there any alternative to mine tw currencies in same time and is it supported by Minera? Do you offer custom development/support of Minera also?
|
|
|
|
jccoro
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 27, 2017, 02:48:48 AM Last edit: May 28, 2017, 03:12:59 PM by jccoro |
|
Hi Michelem and all the comunity.
Can someone help me?
I just get a ZeusMiner Thunder x3 128 chips. im trying to setting up with cgminer but im getting a lot of errors. Can you tell me the correct setting on miner settings? including all the available options tu run it ok The settings i have now are: --scrypt --zeus-chips 128 --zeus-clock 280 the clock i change it to 328, 333 and the same.
hope you can help me.
thanks a lot!!
|
|
|
|
jccoro
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 28, 2017, 05:22:32 PM |
|
Hi Michelem and all the comunity.
Can someone help me?
I just get a ZeusMiner Thunder x3 128 chips. im trying to setting up with cgminer but im getting a lot of errors. Can you tell me the correct setting on miner settings? including all the available options tu run it ok The settings i have now are: --scrypt --zeus-chips 128 --zeus-clock 280 the clock i change it to 328, 333 and the same.
hope you can help me.
thanks a lot!!
I found the correct settings: --scrypt --zeus-chips 128 --zeus-clock 340 --retries 1 Only missing instruction is temperature. Can some one tell me how to show the correct temp?. Using CGminer Thanks
|
|
|
|
hallo_frosch
Member
Offline
Activity: 87
Merit: 10
|
|
May 31, 2017, 12:31:50 PM |
|
Hello Michelem,
since a few days my Minera installation stops collectiing data for hashrate and WU´s after a few hours uptime. There is plenty of free space on the Pi´s SD-Card and the file system seems intact. Do you have a tip what´s the cause for this behavior ? Regards
Stephan
|
|
|
|
T0rNie
Newbie
Offline
Activity: 17
Merit: 0
|
|
June 03, 2017, 09:08:47 PM |
|
Hello there,
I did a fresh install of minera at my Raspberry Pi and it doesn't want to connect with the ethernet.. Any clue?
|
|
|
|
giantkin
|
|
June 03, 2017, 10:04:10 PM |
|
Hello there,
I did a fresh install of minera at my Raspberry Pi and it doesn't want to connect with the ethernet.. Any clue?
First step... do the basics. Check the cords, yup, unplug and replug everything. which version of pi? with wireless/without give more details on the steps you've already tried. sure, lots of times its something more... but if you list the things you did do... noone has to think about them first. is your router letting the connection in... did you switch the wireless settings for the new setup? im guessing it got a new ip, and myabe its blocked... everything else is working but that? your having trouble with wireless part? plug it directly, now it works... IE: pinpoint the problem by elimination ... gl
|
http://choicehost.biz Domains and DIY -hosting I save $5 or so, for each domain a year. (Compared to other Domain Registrars)
|
|
|
|