ANTMINER S5: 1155GH(+OverClock Potential), In Stock $0.319/GH & 0.51W/GH

[Rabinovitch]

Hello!

What was temp difference going from normal fan to that?

In Moscow it is now 20°. Indoor 35°.
Antminer 44°-47°
fan 240RPM

Well, S5 can work even without such perversions. 

Are you OK with 35°C indoor? 

[notlist3d]

Hello!

What was temp difference going from normal fan to that?

In Moscow it is now 20°. Indoor 35°.
Antminer 44°-47°
fan 240RPM

Well, S5 can work even without such perversions. 

Are you OK with 35°C indoor? 

He should be ok with manual it says "Operating ambient temp 0-35 C"   So it's right at the top.

I would wonder if it's in a garage or work area possibly to have that as ambient. I'm thinking the indoor is not like a house indoors with AC.  I did a overhaul for summer mining with fans.   And I have had no problems with any of the miners including S5 so far.  It's reached 85 or so max.   I do have some high CFM fans helping miners.   

I am running at stock speeds.   And I am very happy with mining during summer so far.

[igorwhite]

Well, S5 can work even without such perversions.  Wink

Are you OK with 35°C indoor?

All works fine
I have in this room a lot asic

[marvykkio]

I need to talk to someone who has fans, TCF1212DE (DELTA). someone there?

I can't find that model with Google (typo maybe).  I have Delta fans on my S5's.  I just hooked them onto the fans ports on the controller.  What's going on for you

these are the fan, but now I know for sure that the controller S5 can not handle

http://www.cwc-group.com/tfc1212desp07.html

[Crypto84]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

[aarons6]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

good question. the s3 has many more options then the s5 does..

are all your s5s connected to one network? you can always setup a vpn and connect to that through the firewall.. then you would have complete access to all the miners.

[Crypto84]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

good question. the s3 has many more options then the s5 does..

are all your s5s connected to one network? you can always setup a vpn and connect to that through the firewall.. then you would have complete access to all the miners.

Looks like it runs lighttpd i can edit the lighttpd.conf file. if i mess this up will hitting the reset button on the miner do anything?

http://redmine.lighttpd.net/boards/2/topics/4110

[PatSNL]

I need to talk to someone who has fans, TCF1212DE (DELTA). someone there?

I can't find that model with Google (typo maybe).  I have Delta fans on my S5's.  I just hooked them onto the fans ports on the controller.  What's going on for you

these are the fan, but now I know for sure that the controller S5 can not handle

http://www.cwc-group.com/tfc1212desp07.html

Some people had to change the order of the wires to work proper.   

Mine are the Delta AFB1212SHE and worked with the standard wiring configuration.

I hope you can get yours to work.

[Mudbankkeith]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

I use ipscan24.exe  (freeware from last year on this thread)
All s5 are on one network.

scans all ports for all devices.

[aarons6]

I need to talk to someone who has fans, TCF1212DE (DELTA). someone there?

I can't find that model with Google (typo maybe).  I have Delta fans on my S5's.  I just hooked them onto the fans ports on the controller.  What's going on for you

these are the fan, but now I know for sure that the controller S5 can not handle

http://www.cwc-group.com/tfc1212desp07.html

Some people had to change the order of the wires to work proper.  

Mine are the Delta AFB1212SHE and worked with the standard wiring configuration.

I hope you can get yours to work.

yours was a 5 pin fan, thats why..
yours is also only 1.6A


his is a 4pin PWM with Speed Sensor Inverter and also 4 AMPS per fan.. (i think he got the cheapest fans he can find as the afb fan is usually about 5-10$ more)

basically he has 2 issues.. well more then 2 issues since i have said this in 3 of his threads that he created..

issue 1, the s5 controller cant do 4 amps on the board.. when i plugged mine in the s5 woudlnt even turn on..

issue 2 is that fan as an inverted pwm controller.. you see normal fans have a pwm that uses 0v for full speed and 5v for off.. this is why when you cut the blue wire the fan goes full speed..
on this fan, it uses 0v for off and 5v for full speed..

this means that if you dont connect the blue wire to ~5v, the fan wont even turn on.

this is an issue on the s5 becuase when you first turn on the s5 it puts 0v to the pwm line, making the original fan turn on full speed while the unit is booting up.. but this fan wont appear to do anything at all. (since it wont boot up with 4 amp fans it probably wont ever do anything)
then when the s5 boots up, it lowers the volts down to whatever is needed temp wise. but since this fan is backwards, it will actually slow down as temps increase, eventually turning back off again as this fan wont run at under 2000 rpms or so.. so even if you hook the red and black wire to the black and yellow wires of a molex and then use the blue and yellow wires on this fan connected to the fan header it still wont work correctly

[toptek]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

I use ipscan24.exe  (freeware from last year on this thread)
All s5 are on one network.

scans all ports for all devices.

http://www.advanced-ip-scanner.com/?utm_expid=62919999-2.Y9iZ50TUTPOtSKALjFcehg.0&utm_referrer=http%3A%2F%2Fwww.google.com%2Furl%3Fsa%3Dt%26rct%3Dj%26q%3D%26esrc%3Ds%26source%3Dweb%26cd%3D1%26ved%3D0CB8QFjAA%26url%3Dhttp%253A%252F%252Fwww.advanced-ip-scanner.com%252F%26ei%3D9UNyVYnvH4KdgwTIhYDQBw%26usg%3DAFQjCNHb-tg5d4NJPy4r_dPloXJpAhSYXQ%26bvm%3Dbv.95039771%2Cd.eXY

or this one unless that's the same one not sure .



yup same one !!! .

[notlist3d]

anyone know how to change the http port from 80 on the S5? i want to port forward to it and i need my second one on a different port.

I use ipscan24.exe  (freeware from last year on this thread)
All s5 are on one network.

scans all ports for all devices.

http://www.advanced-ip-scanner.com/?utm_expid=62919999-2.Y9iZ50TUTPOtSKALjFcehg.0&utm_referrer=http%3A%2F%2Fwww.google.com%2Furl%3Fsa%3Dt%26rct%3Dj%26q%3D%26esrc%3Ds%26source%3Dweb%26cd%3D1%26ved%3D0CB8QFjAA%26url%3Dhttp%253A%252F%252Fwww.advanced-ip-scanner.com%252F%26ei%3D9UNyVYnvH4KdgwTIhYDQBw%26usg%3DAFQjCNHb-tg5d4NJPy4r_dPloXJpAhSYXQ%26bvm%3Dbv.95039771%2Cd.eXY

or this one unless that's the same one not sure .



yup same one !!! .

Also if you have a decent router looking at connected devices can do wonders.  Part of it depends on how many items you have connected to network.

But if you look at device list normally you can start going to IP's and find it.

[aarons6]

you guys are all miss understanding what he wants.. its not that he cant find the s5s on the network.

he wants to connect with them over the internet or something.. which is a bad idea..

i told him he should setup a vpn through windows and then he can access all the miners like he was at home.. but he ignored me.

[notlist3d]

you guys are all miss understanding what he wants.. its not that he cant find the s5s on the network.

he wants to connect with them over the internet or something.. which is a bad idea..

i told him he should setup a vpn through windows and then he can access all the miners like he was at home.. but he ignored me.

I personally would throw them behind a firewall/router.   You can use VPN/Teamviewer, etc to log into home network and change items as you want.

This way you don't have them out there for the world to see.

[Crypto84]

you guys are all miss understanding what he wants.. its not that he cant find the s5s on the network.

he wants to connect with them over the internet or something.. which is a bad idea..

i told him he should setup a vpn through windows and then he can access all the miners like he was at home.. but he ignored me.

I personally would throw them behind a firewall/router.   You can use VPN/Teamviewer, etc to log into home network and change items as you want.

This way you don't have them out there for the world to see.

this is what im trying to do. Im currently using teamviewer.I have new 13" macbook pro i leave on all day. it only uses less than 8.6watts idle with the screen off. I was just looking for a better solution. guess ill have to stick with this.

[oztusk]

overclocking c1... what voltage can i go up to before im redlining? where does it become unsafe?

[dogie]

overclocking c1... what voltage can i go up to before im redlining? where does it become unsafe?

While no amount of overclocking is safe, I personally wouldn't go above 72-740. You shouldn't really need to bump voltage to overclock though, you'll cap out the chips before any additional voltage will help.

[Fatman3001]

Question to Bitmain, Dogie or whoever is in the know:

Will Bitmain sell their next gen 14/16nm Finfet machines or solely mine themselves? Any time frame?

[oztusk]

Question to Bitmain, Dogie or whoever is in the know:

Will Bitmain sell their next gen 14/16nm Finfet machines or solely mine themselves? Any time frame?

Bitmain says s7 late july.

idk if this is 14 nm though....

i reckon Bitmain will always sell miners to anyone who buys them and pays the electric bill.
much easier profit for Bitmain that way.

[aarons6]

Question to Bitmain, Dogie or whoever is in the know:

Will Bitmain sell their next gen 14/16nm Finfet machines or solely mine themselves? Any time frame?

Bitmain says s7 late july.

idk if this is 14 nm though....

im not seeing any official announcements..

where do you get this s7 story?