Latest posts of: marto74

Wes the assembly service will be run by my company

Quote from: jkminkov on May 29, 2013, 07:24:16 PM

ако не съберем хора за 10К чипа какво става с поръчката Roll Eyes

Щe съберем

Все пак ако не стане Джон ще възстанови парите на всички по адресите на изпращане , а аза ще платя ескроу таксата от джоба си
Доста време се въздържах да пусна такава поръчка, но на лично ми потвърдиха няколко колеги по-големшки бройки и реших да се мятам.

Това е за К16
ЗА вентилаторите си прав и все пак ги има
Ще го решаваме когато направим прототип

this is OK?
I have something in mind to insist on 200x200 heatsink

3D sample design of 4xK16 over 200x200x25 heatsink.
This sink can be used as frame to be attached in 4-7 board mining device

I think you are right
here it is corrected

Sample 3D design of 4 x K16 over 200x200x25 mm heatsink

Here is a sample design of 4 K16 daisychained with 200x200x25 mm heatsink as frame

Sample 3D of the K16 with heatsink and 100 mm fan

Quote from: steamboat on May 29, 2013, 06:12:02 AM

Quote from: marto74 on May 29, 2013, 06:05:08 AM

How a single K16 with heatsink and fan will look

It's eerie how similar our designs are.

So there are 2 options:
Both We are doing great
Both made a mistake

We'll see when some chips are here working and distributing the heat

How a single K16 with heatsink and fan will look

In any case We are going to accept orders only after We have a working sample of the board design

Quote from: giulianoob on May 28, 2013, 07:38:20 PM

Would this adapter be suitable to power the boards?

For now We are going to use PCI-e . that said the adapter in your link will work with older PSU that have only molex conectors.
Most of the modern PSU have a few 6 pin PCI-e conectors integrated .
Of course later we can decide to put directly molex conectors or laptop type conector for a power brick

Quote from: prophetx on May 28, 2013, 07:46:38 PM

Quote from: marto74 on May 28, 2013, 07:30:43 PM

The assembly service we offer is including:
1. Prouction of PCB
2. Delivery of all the components excluding of ASIC chip
3. Asic chip delivered by you to us
4. Full smt assembly of the board.
5. Firmware upload and setup on the board
6. Test

In order to receive assembled board you'll have to send us your chips

Aditionaly you cаn order with us custom heat sink, suitable fan and even full assembled in an enclousure miner with 4-8 boards

great thanks!

And the cost for steps 1 - 6 (excluding cost of chip and delivery of chip to you) is between 46 to 55 Euros? Or is that just for 1 and 2?

1-6

Quote from: jelin1984 on May 28, 2013, 01:07:15 PM

Hello any photo to see the miner

Hi this is a group buy for this
http://store.avalon-asics.com/?page_id=9605

We are then offering assembly service with these chips
here
https://bitcointalk.org/index.php?topic=212031.0
The project is still in design , but will be ready for the arrival of the first sample chips from Avalon - mid June

marto74;12; 1.02; 12DNdacCtUZ99qcP74FwchaCPzeDL9Voff

Confirmed (not payed) for now

marto74 - 50
dimomit - 1500
skrubalov - 16
kokoboko- 100
______________
1666
8334 chip left