myself in USA I simply have 1 220v circuit wired with 12avg wire rated at 20 amps with a 20 amp 220v double pole breaker and of course the 220v plug at the wall...to do so
into an ISOBAR Euro4 version surge protector 4 volt....here off amazon..I have 3 total 220v plugs/circuits and an isobar euro4 on each one...

http://www.amazon.com/Tripp-Lite-EURO-4-International-Protector/dp/B00006HZ4M/ref=sr_1_3?ie=UTF8&qid=1406427314&sr=8-3&keywords=euro+4

it is cheaper then a PDU and works for my needs...

this was easy to do because in my case it is in the bsmt near the panel..so what the heck overkill....1 power supply of the 2 on the sp30 will be plugged
into the above 20amp breaker/20 amp socket/indv 220v euro4 isobar for each 20amp line/breaker (again this model eruo4 at 220v because the sp30 comes
with cords that work for this)

YOU DO need however to purchase the 220v cord from the power outlet to the euro4 isobar..(it has interchangeable cords) the euro4 comes with the
same type of cord as the sp30 miners will come with...not the one that goes from the 220v isobar to the plug in the wall..you need to match (see below)

below is cords that come with the sp30 and the isobar euro4 above (at least the end that does not plug into the sp30 power supply that can be a different type)

http://www.amazon.com/gp/product/B003MG9F78/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

below here is the 3 220v cords from the isobar4 4 surge protector to the plug on the wall...

http://www.amazon.com/gp/product/B0093WFT5C/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

so yeah way over kill but....should work fine 3 circuits using 3 euro4 isobars...1 for each power supply on the sp30 and 1 for the KNC Titan if/when it comes

again overkill but what the heck...as to the tripplite isobars ...well they have saved my butt before so better safe then sorry...
and again cheaper then a PDU

(silly hobby I could have got a bass boat and it probably would have sunk....with my luck anyway..go figure....toys..toys...toys...)

Searing

We're communicating. We don't want to give inaccurate information. Stabilizing new system and new firmware takes time. Stress testing the systems also takes time.
I repeat my original request, please be patient.

Guy

Talk to a local electrician or talk to a friend of a friend who is one. This is not something you buy on eBay and do yourself. If you have a 16A breaker for all the outlets in your sleeping room you can use 12.8A of it (to stay within the 80% of the rating). If you need more than that, you could plugin the second power supply/cable in another room.

How much current the SP30 will pull will be clear by next week I guess. At 1200W the Murata PSU is rated 8A @ 200V, there are two.


These seem about right, but you need to add a bit of space for the handles of the PSUs and cabling. About 580mm total length, rest seems right. Add lots of space for air flow, do not obstruct front and back. And expect noise.
 

Look for a 30AMP outlet. You will usually find this in the kitchen around the stove and various enclaves where you plug in toasters and microwaves. This is where you can run an SP30 via heaviest duty extension cord if you don't want it competing with the blender noise or coffee grinder noise:

15-amp Circuit
Total Wattage Capacity: 15 amps x 120 volts = 1,800 watts  
Safe Wattage Capacity: 1,800 watts x 80% = 1,440 watts
Safe Amperage Capacity: 15 amps x 80% = 12 amps

20-amp Circuit

Total Wattage Capacity: 20 amps x 120 volts = 2,400 watts  
Safe Wattage Capacity: 2,400 watts x 80% = 1,920 watts
Safe Amperage Capacity: 20 amps x 80% = 16 amps

30-amp Circuit

Total Wattage Capacity: 30 amps x 120 volts = 3,600 watts
Safe Wattage Capacity: 3,600 watts x 80% = 2,880 watts
Safe Amperage Capacity: 30 amps x 80% = 24 amps

That's all good and nice for America with 120V or so, but in the civilized world we use something else
He asked if it would work with "230v 50Hz mains socket".

You need to know the amperage of the circuit breaker where you connect the SP30 to, or each of the power supplies. Not the main breaker.

SP30s are a continuous load (they are expected to run for 3 hours or longer at a time at full load), which means that their loads have to be multiplied by 125% before comparing the load to the circuit ampacity.

125% * 2750W / 220V = 15.0 amps. There's a chance you might be able to put that on a 15 amp circuit without tripping any breakers, but you should be planning for the worst, not for the best. Typical circuit breakers will have a moderate to high chance of tripping if they are loaded at a continuous 80% of their rated capacity.

http://advanceelectricaltraining.com/advance-electrical-training/continuous-loads-decoded/

The 125% (or 80%) rule is all over the place in the National Electric Code. It's also how circuit breakers generally work. You can get away with loading circuits higher than that sometimes, but it's basically the electrician equivalent of overclocking. You shouldn't do it unless you have a back-up plan and don't care much about breaking laws and tripping breakers.

Assholes deleted my post. It's okay, because most everything is known and archived.

But if you requested a refund from Minersource and did not get it, but they've tried to send you your equipment, drop me a message.

Yeah, they deleted my post too, fools.

I don't know if it would help or hurt, but perhaps opening the lawsuit up to being some type of class action suit. Wouldn't lawyers like this? The more they recoup the more they get? I know a lot of people who have been burned would more likely than not jump on board, if someone is willing to take the case perhaps it could sweeten the pot for them that much more.

Even the merchandise they have shipped seems to be sub par at best and missing things that were supposed to be included when originally ordered i.e lcd screens.

There is another non moderated thread for BA.

I just need the mounting ears for a standard data center 2U rack mount. Not sure what you call them. That seems like a ton of heat for an Apartment. I use air cooling in a Large Garage I pay for and its quite warm with 4000KW. Unless your Apartment is very Large?

I'm basically just curious, seems like a lot of power for an Apartment I guess.

But that "cabinet" is only 200mm deep.   

Patient please. We'll start shipping the SP30s and release more information next week.

Guy

Anyone have a link for what mounting rails/ears? Or specs on what to buy?

Should add meant for Sp30.

Where did you read this?

I have 9 Rigs in my possession, so they have shipped some....

I have updated the projected hardware to btc return chard and spread sheet to include the aug sept and original prices of the sp30.



Shared link to document. https://docs.google.com/spreadsheet/ccc?key=0AmeuPljmUNHCdEpqX2RmMDFwemJyLURVUWFtZ3J3aGc&usp=sharing