Xenland (OP)
Legendary
Offline
Activity: 980
Merit: 1003
I'm not just any shaman, I'm a Sha256man
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 07:36:48 AM |
|
upstream_result = 'Y' ===> you found a block, NULL ===> wait moar
![Shocked](https://bitcointalk.org/Smileys/default/shocked.gif) Learn something new every day Are you serious ? You really didn't know that ? If you were just being sarcastic then sorry ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) If you weren't you should consider using it to properly monitor generated blocks. Are you just polling bitcoind to check for new blocks from time to time ? Its a little more complex then that but its not as practical. Then again when i think about it even if i did do it this way id still require all the checks and updates i have in place either way.
|
|
|
|
Chucksta
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 08:03:17 AM |
|
My installation of Pushpool seems to be falling down at the installation of Libmemcached.. Anyone know for why I get the following errors when running "make install" ? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.internetmarketier.com%2Fimages%2Fpushpool%2520libmemcached%2520error.jpg&t=665&c=pNGK2i2tPYRGow) I have tried both 0.48 and 0.49. Both give the same errors ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) Of course, when I try to install Pushpool, it complains that Libmemcached is not installed. Ubuntu 11.04 (64) being used.
|
|
|
|
Xenland (OP)
Legendary
Offline
Activity: 980
Merit: 1003
I'm not just any shaman, I'm a Sha256man
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 08:11:36 AM |
|
My installation of Pushpool seems to be falling down at the installation of Libmemcached.. Anyone know for why I get the following errors when running "make install" ? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.internetmarketier.com%2Fimages%2Fpushpool%2520libmemcached%2520error.jpg&t=665&c=pNGK2i2tPYRGow) I have tried both 0.48 and 0.49. Both give the same errors ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) Of course, when I try to install Pushpool, it complains that Libmemcached is not installed. Ubuntu 11.04 (64) being used. Make sure you have all the pre requisites for libmemcached. Ill post up a link to a list when i have more time
|
|
|
|
Chucksta
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 08:45:58 AM |
|
Make sure you have all the pre requisites for libmemcached. Ill post up a link to a list when i have more time
Thanks, I'll do some more Googling.. not much luck so far ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) , but I'll persevere !
|
|
|
|
Chucksta
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 09:22:46 AM |
|
Do'h... Silly me, you need to use sudo: sudo make installAll okay now ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
slowmining
Newbie
Offline
Activity: 22
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 03:13:03 PM |
|
It's recommanded to save all the shares without deleting them from the main table? Because my pool will be public and the number of shares in the table could be very big. For now I'm storing into an another table the number of shares per round of each worker in a table and deleting all the shares in the main table. Am I doing it wrong?
|
|
|
|
Xenland (OP)
Legendary
Offline
Activity: 980
Merit: 1003
I'm not just any shaman, I'm a Sha256man
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 03:43:27 PM |
|
It's recommended to save all the shares without deleting them from the main table? Because my pool will be public and the number of shares in the table could be very big. For now I'm storing into an another table the number of shares per round of each worker in a table and deleting all the shares in the main table. Am I doing it wrong?
Yes this is how MiningFarm#2 works, I found it efficient to have a current round shares table, and when the round is over move all the shares to a history of shares table. Upon transferring to the history MF2 splits up the profit. You should check out my code in the cronjob folder a bunch of little tid bits like that Mining Farm #2: http://forum.bitcoin.org/index.php?topic=10617.0
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 07:17:51 PM |
|
ignore my earlier plea for help, now pushpoold is starting, and bitcoind is running. i am getting ustream RPC error on the miner, and JSON protocol request: {"method": "getwork", "params": [], "id":26}
* About to connect() to 127.0.0.1 port 8332 (#0) * Trying 127.0.0.1... * TCP_NODELAY set * connected * Connected to 127.0.0.1 (127.0.0.1) port 8332 (#0) * Server auth using Basic with user 'rpcproxy' > POST / HTTP/1.1 Authorization: Basic cnBjcHJveHk6bG9vcHAwMGxQdXNo Host: 127.0.0.1:8332 Accept: */* Accept-Encoding: deflate, gzip Content-type: application/json Content-Length: 46
* The requested URL returned error: 500 * Closing connection #0
server.json { # network ports "listen" : [ # binary protocol (default), port 8336 # { "port" : 8336 },
# HTTP JSON-RPC protocol, port 8337 { "port" : 8337, "protocol" : "http-json" },
# HTTP JSON-RPC protocol, port 8339, # with trusted proxy appserver.example.com forwarding # requests to us { "port" : 8339, "protocol" : "http-json", "proxy" : "derp.com" },
# binary protocol, localhost-only port 8338 { "host" : "127.0.0.1", "port" : 8338, "protocol" : "binary" } ],
# database settings "database" : { "engine" : "mysql",
# 'host' defaults to localhost, if not specified # "host" : "mysql.example.com",
# 'port' uses proper default port for the DB engine, # if not specified # "port" : 12121,
"name" : "sc", "username" : "pushpool", "password" : "hurpadurp",
"stmt.pwdb" : "SELECT password FROM pool_worker WHERE username = ?" },
# cache settings "memcached" : { "servers" : [ { "host" : "127.0.0.1", "port" : 11211 } ] },
"pid" : "/tmp/pushpoold.pid",
# overrides local hostname detection "forcehost" : "localhost.localdomain",
"log.requests" : "/tmp/request.log", "log.shares" : "/tmp/shares.log",
# the server assumes longpolling (w/ SIGUSR1 called for each blk) "longpoll.disable" : false,
# length of time to cache username/password credentials, in seconds "auth.cred_cache.expire" : 75,
# RPC settings "rpc.url" : "http://127.0.0.1:8332/", "rpc.user" : "rpcproxy", "rpc.pass" : "hurpadurp",
# rewrite returned 'target' to difficulty-1? "rpc.target.rewrite" : true
and bitcoin.conf # JSON-RPC options (for controlling a running Bitcoin/bitcoind process)
# server=1 tells Bitcoin to accept JSON-RPC commands. server=1
# You must set rpcuser and rpcpassword to secure the JSON-RPC api rpcuser=rpcproxy rpcpassword=hurpadurp
# How many seconds bitcoin will wait for a complete RPC HTTP request. # after the HTTP connection is established. rpctimeout=30
# By default, only RPC connections from localhost are allowed. Specify # as many rpcallowip= settings as you like to allow connections from # other hosts (and you may use * as a wildcard character): #rpcallowip=[i][b]I ASSUME LOCALHOST IS ON BY DEFAULT[/b][/i] #rpcallowip=192.168.1.*
# Listen for RPC connections on this TCP port: rpcport=8332
links http://127.0.0.1:8332/user rpcproxy pass hurpadurp {"result":null,"error":{"code":-32700,"message":"Parse error"},"id":null}
|
|
|
|
deluxor
Newbie
Offline
Activity: 8
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 09:45:22 PM |
|
I have exactly the same problem in above post! Please tell me what is wrong?
Thanks
|
|
|
|
uncooper
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 09:54:57 PM |
|
Jun 11 05:02:55 ip-10-124-17-59 pushpoold[18787]: tcp socket: Address family not supported by protocol
How did you resolved this error?
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 11, 2011, 11:55:55 PM Last edit: June 12, 2011, 12:32:37 AM by genewitch |
|
pushpool is not setting mysql pool_worker "active" and hashrate. pushpool is working, because it accepts the login i gave it and throws client errors if i use anything else. Pushpool is also not updated the "shares" table with any data, it says it's an empty set. mysql> select * from sc.pool_worker; +----+------------------+-------------+----------+--------+----------+ | id | associatedUserId | username | password | active | hashrate | +----+------------------+-------------+----------+--------+----------+ | 1 | 1 | genewitch.1 | x | 0 | 0 | +----+------------------+-------------+----------+--------+----------+ 1 row in set (0.00 sec)
mysql> select * from sc.shares; Empty set (0.00 sec)
Do i need to write the logic to set these, or should pushpoold be doing this itself? Please advise! :-D edit: /tmp/shares.log is full of stuff: [2011-06-12 00:30:9.000529] ::ffff:76.91.146.36 genewitch.1 Y - - 000000011023d492df81b494de90f30e854e953d1e72515dad22dd21000013a800000000633913820a277592654e47a21fe21701c20f542b45b0c2c345cea70e66c5ba204df4088e1a1d932f5e7ff9ff000000800000000000000000000000000000000000000000000000000000000000000000000000000000000080020000 [2011-06-12 00:30:12.190757] ::ffff:76.91.146.36 genewitch.1 Y - - 000000011023d492df81b494de90f30e854e953d1e72515dad22dd21000013a800000000633913820a277592654e47a21fe21701c20f542b45b0c2c345cea70e66c5ba204df408911a1d932f073e1230000000800000000000000000000000000000000000000000000000000000000000000000000000000000000080020000
So obviously something is going wrong somewhere in the database calls. I'd like to know if i screwed something up or if there's something i can help patch. I know it is a weekend, though, so i'll just grin and bear it for now. edit: my miner has been running ~300MH/s for hours now, and has submitted nearly a thousand shares (and they were accepted) - but this isn't reflected anywhere in the database. Is this a privilege setting or something? I have exactly the same problem in above post! Please tell me what is wrong?
Thanks
Actually it resolved itself, bitcoind had to run for about 20 minutes before it finally stopped giving upstream RPC errors and connection lost in the client. Jun 11 05:02:55 ip-10-124-17-59 pushpoold[18787]: tcp socket: Address family not supported by protocol
How did you resolved this error? Stopped using gentoo and switched to ubuntu. It has something to do with ipv6, although on gentoo i changed USE="-ipv6 ipv4" and did emerge -DN @world and it did not fix it. edit to ^: It's a gentoo issue 90% and the code in pushpool 10% because of the way that it gets a socket. I am not a C programmer. I cannot patch this while ensuring it works for everyone. Thanks to the developers for making something like this that is free and works at all. I couldn't have done it, that's for sure.
|
|
|
|
deluxor
Newbie
Offline
Activity: 8
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 01:59:37 AM |
|
YAY! Thanks dude! ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif) But now im stucked as you... ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) Seems that we have the same problems! LOL BTW dude check your PM folder pls
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 02:00:11 AM Last edit: June 12, 2011, 02:57:10 AM by genewitch |
|
the pin cannot start with 0. if you try it throws invalid pin. probably because whatever command php uses to determine the length cuts leading zeros. bug just cost me a pool worker :-( in register.php (onyl one i looked at) look for this section
$authPin = (int) $_POST["authPin"]; change to: $authPin = (string) $_POST["authPin"]; look for: //valid date authpin is valid change the block under it to read: //valid date authpin is valid if(strlen($authPin) >= 4){ if(!is_numeric($authPin)){ $validRegister = 0; $returnError .= " | Not a valid authpin"; } }else{ $validRegister = 0; $returnError .= " | Authorization pin number is not valid"; } verified myself this time. ![Roll Eyes](https://bitcointalk.org/Smileys/default/rolleyes.gif)
|
|
|
|
deluxor
Newbie
Offline
Activity: 8
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 02:02:52 AM Last edit: June 12, 2011, 02:20:48 AM by deluxor |
|
|
|
|
|
Xenland (OP)
Legendary
Offline
Activity: 980
Merit: 1003
I'm not just any shaman, I'm a Sha256man
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 02:35:01 AM |
|
the pin cannot start with 0. if you try it throws invalid pin. probably because whatever command php uses to determine the length cuts leading zeros. bug just cost me a pool worker :-(
in register.php (onyl one i looked at) look for this section
//valid date authpin is valid if($authPin > 9999){ if(!is_int($authPin)){ $validRegister = 0; $returnError .= " | Not a valid authpin"; } }else{ $validRegister = 0; $returnError .= " | Authorization pin number is not valid"; }
change the strlen($authpin) >=4 to what i put there so it looks just like that.
In lieu, another suggestion was strlen(('x' + $authpin) -1)
Thanks for the bug report ill have that fix uploaded very soon. On a features note im still on schedule i just got my 6990 so trying to ge that running so i can get back to work on the features like worker graphs, blog updates editor, and i still have to test out a potential bug in the blockfound page. Thanks for everyone patience in this down time
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 03:34:26 AM Last edit: June 12, 2011, 04:18:40 AM by genewitch |
|
the pin cannot start with 0. if you try it throws invalid pin. probably because whatever command php uses to determine the length cuts leading zeros.
Thanks for the bug report ill have that fix uploaded very soon. On a features note im still on schedule i just got my 6990 so trying to ge that running so i can get back to work on the features like worker graphs, blog updates editor, and i still have to test out a potential bug in the blockfound page. Thanks for everyone patience in this down time don't use the patch i typed up there it doesn't work. use this patchfile 55c55 < $authPin = (int) $_POST["authPin"]; --- > $authPin = (string) $_POST["authPin"]; 89c89 < if(!is_int($authPin)){ --- > if(!is_numeric($authPin)){
pushpulld isn't updating anything in the mysql database, such as shares, active column in the pool_worker table, hashrate, etc. I haven't gone through everything but as far as i can tell it's not doing any updates of the tables. Any way to debug this?
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 06:34:22 AM |
|
for those hitting my errors earlier: use these command to pull the latest source for pushpool git clone https://github.com/jgarzik/pushpool.git cd pushpool ./autogen.sh ./configure make sudo make installsetup your server.json properly, make sure you add to the "database" section. start pushpoold. handle your business. *autogen.sh fails on EC2 ubuntu natty narwhal, you have to to get aclocal!
|
|
|
|
Xenland (OP)
Legendary
Offline
Activity: 980
Merit: 1003
I'm not just any shaman, I'm a Sha256man
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 09:54:38 AM |
|
the pin cannot start with 0. if you try it throws invalid pin. probably because whatever command php uses to determine the length cuts leading zeros.
Thanks for the bug report ill have that fix uploaded very soon. On a features note im still on schedule i just got my 6990 so trying to ge that running so i can get back to work on the features like worker graphs, blog updates editor, and i still have to test out a potential bug in the blockfound page. Thanks for everyone patience in this down time don't use the patch i typed up there it doesn't work. use this patchfile 55c55 < $authPin = (int) $_POST["authPin"]; --- > $authPin = (string) $_POST["authPin"]; 89c89 < if(!is_int($authPin)){ --- > if(!is_numeric($authPin)){
pushpulld isn't updating anything in the mysql database, such as shares, active column in the pool_worker table, hashrate, etc. I haven't gone through everything but as far as i can tell it's not doing any updates of the tables. Any way to debug this? I have a question for you, where are you getting your hashrates for you tend to mention this alot, Im so confused
|
|
|
|
dikidera
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 02:50:41 PM |
|
genewitch - pushpool has never calculated hashrate. I don't understand how you even had this idea in the first place.
|
|
|
|
genewitch
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
June 12, 2011, 04:59:01 PM |
|
genewitch - pushpool has never calculated hashrate. I don't understand how you even had this idea in the first place.
pushpool was not putting anything in the database, just reading from it. Therefore every other piece of software that relied on the shares table to be updated by pushpoold was not calculating the hashrate, or activity. Picking one part of my statement that is incorrect and lambasting it without acknowledging the real problem is called the strawman fallacy. I got it working (there was a bug somewhere in the pushpoold code, haven't diffed everything to figure out where yet) - and i will write a guide that uses the git snapshot i have as a base. It just took 12 hours on my part and a lot of "works for everyone else!!!!!!111" from others. I'm still glad the software exists, though.
|
|
|
|
|