ANTMINER S7 is available at bitmaintech.com with 4.86TH/s, 0.25J/GH

[AriesIV10]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order 

I am sure to those that bought Batch 8 the coupon is appreciated, but there was to be some compensation for late orders on Batch1 along with the low hash rates of some of the Batch 1.  Is this coming soon?

[AriesIV10]

Batch 8 is for sale again.  Looks like a lower price.


ANTMINER S7 BATCH 8
Speed:    4.73TH/S
Weight:    4.5 kg
Price:       1650 USD
               ( 4.368 BTC )

[fullzero]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order 

 Batch 1 compensation?

[Ironworm]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order 

 Batch 1 compensation?

Havnt heard anything yet

[philipma1957]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order 

So I purchased  Batch 1  and one machine consistently runs under spec where is my coupon?

[fr4nkthetank]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order  

checking...coupon is there !  150usd coupon.  Well thanks Bitmain.  But i'm a bit confused.  I paid 4.73btc - which was around 1500usd at the time, or 1550usd I forget - now the price is 4.45btc, but around 1650usd.  Now I know we can argue btc = btc, but if I were to buy an additionnal s7, it would be with fiat so the cost for me would be 1650usd.  minus coupon, 1500.  and these are shipped at the same time ?  Maybe i'll wait...if btc price goes back down 50$ then the coupon would be a good deal  └(°ᴥ°)┘

[citronick]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

This batch is the worst in terms of efficiency... 700mhz with 135 chips

My first 3 x S7s are very hashing well - except for one unit with a "woooo...wooo..." sound coming from the intake fan.

[Biodom]

My first 3 x S7s are very hashing well - except for one unit with a "woooo...wooo..." sound coming from the intake fan.

Did you try easing the screw(s) just a little-this seemed to help many. I would look at it and see first if they are so overtightened that fan plastic is a bit distorted (I have seen it), then would start with just one screw at first (quarter of a turn or even less), then do the direct opposite, then proceed with other 1-2 if needed. I had to ease just one fan screw on B1 for it to stop making a similar sound.

[fr4nkthetank]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

wat lucky you, I havent heard anything.  I wish it would ship, its already -10celcius here, and my garage is cold

[citronick]

My first 3 x S7s are very hashing well - except for one unit with a "woooo...wooo..." sound coming from the intake fan.

Did you try easing the screw(s) just a little-this seemed to help many. I would look at it and see first if they are so overtightened that fan plastic is a bit distorted (I have seen it), then would start with just one screw at first (quarter of a turn or even less), then do the direct opposite, then proceed with other 1-2 if needed. I had to ease just one fan screw on B1 for it to stop making a similar sound.

Tried all of that but did not help.

I recall a post that "just stuck a piece of tape" to fix it, .... but still no cigar

Now, I have reduced the fan to 55% and that kind of eliminated 95% the annoying sound - that fan speed gives me about 65-67c during day and 59-61c at night.

[citronick]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

wat lucky you, I havent heard anything.  I wish it would ship, its already -10celcius here, and my garage is cold

-10c ... wow I wish I have your kind of weather to maximize the life of these S7s

[Tupsu]

Batch 8 is for sale again.  Looks like a lower price.


ANTMINER S7 BATCH 8
Speed:    4.73TH/S
Weight:    4.5 kg
Price:       1650 USD
               ( 4.368 BTC )

Now, at a fixed price  1650 USD

[yslyung]

My first 3 x S7s are very hashing well - except for one unit with a "woooo...wooo..." sound coming from the intake fan.

Did you try easing the screw(s) just a little-this seemed to help many. I would look at it and see first if they are so overtightened that fan plastic is a bit distorted (I have seen it), then would start with just one screw at first (quarter of a turn or even less), then do the direct opposite, then proceed with other 1-2 if needed. I had to ease just one fan screw on B1 for it to stop making a similar sound.

Tried all of that but did not help.

I recall a post that "just stuck a piece of tape" to fix it, .... but still no cigar

Now, I have reduced the fan to 55% and that kind of eliminated 95% the annoying sound - that fan speed gives me about 65-67c during day and 59-61c at night.

1 of the s7 b5 has this sound too but if fan is 65% & below it is not that loud but still very noticeable.

tried the screw trick no joy. i glued a small heatsink on the right side of the grill that lowered the woo woo woo sound but still there.

any other solutions ?

imo, better wait for next batch. 

[wolfen]

My first 3 x S7s are very hashing well - except for one unit with a "woooo...wooo..." sound coming from the intake fan.

Did you try easing the screw(s) just a little-this seemed to help many. I would look at it and see first if they are so overtightened that fan plastic is a bit distorted (I have seen it), then would start with just one screw at first (quarter of a turn or even less), then do the direct opposite, then proceed with other 1-2 if needed. I had to ease just one fan screw on B1 for it to stop making a similar sound.

Tried all of that but did not help.

I recall a post that "just stuck a piece of tape" to fix it, .... but still no cigar

Now, I have reduced the fan to 55% and that kind of eliminated 95% the annoying sound - that fan speed gives me about 65-67c during day and 59-61c at night.

1 of the s7 b5 has this sound too but if fan is 65% & below it is not that loud but still very noticeable.

tried the screw trick no joy. i glued a small heatsink on the right side of the grill that lowered the woo woo woo sound but still there.

any other solutions ?

imo, better wait for next batch.  

If I hold my hand up kinda close to the back fan the sounds stops. So some kind of rig for that?
Mine are in a datacenter so it can woo woo all day.
I used to put a gutted 120mm fan as a spacer between my s5 front fan and the chassis with 90mm screws.
Also put little spacers between the front grille and the fan giving about a quarter inch of space all around the edge of the grille.
Quieted down the s5 a bit. Fan is more efficient also.
The fan is really too close to the chassis on the s5 and s7.
So maybe a spacer between the back fan and the chassis?

[BitAurum]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

wat lucky you, I havent heard anything.  I wish it would ship, its already -10celcius here, and my garage is cold

-10c ... wow I wish I have your kind of weather to maximize the life of these S7s

I wish I had that kind of weather.
@citronick, What's the electricity rates at the location you live?

[thedreamer]

Coupons were offered to customers who bought S7 Batch 8 and the order has been paid till Nov. 30, 19:00 of Beijing time.
Please kindly check your account if you've already had Batch 8 order  

HOW ABOUT ANSWERING YOUR TICKETS REGARDING THE COMPENSATION OF BATCH1'S AND OTHER FINANCE RELATED QUESTIONS?

Ticket ID:#4955
Ticket ID:#4923

Bother opened 15 and 16 days ago!

[citronick]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

wat lucky you, I havent heard anything.  I wish it would ship, its already -10celcius here, and my garage is cold

-10c ... wow I wish I have your kind of weather to maximize the life of these S7s

I wish I had that kind of weather.
@citronick, What's the electricity rates at the location you live?

The electricity rates here is expensive SGD$0.21kwh or about SGD$175 per S7 per month. SGD/USD ROE 1.4

[dmwardjr]

If I hold my hand up kinda close to the back fan the sounds stops. So some kind of rig for that?
Mine are in a datacenter so it can woo woo all day.
I used to put a gutted 120mm fan as a spacer between my s5 front fan and the chassis with 90mm screws.
Also put little spacers between the front grille and the fan giving about a quarter inch of space all around the edge of the grille.
Quieted down the s5 a bit. Fan is more efficient also.
The fan is really too close to the chassis on the s5 and s7.
So maybe a spacer between the back fan and the chassis?

I would agree with using your hand to investigate.  What I did was use two fingers extended out over the edge over the back fan and the front fan.  I would move my two fingers (index and middle finger) around the edge in a circular motion until my fingers were at a point where the noise was no longer audible.  Once I found the location where the air being sucked in was no longer audible, I placed only one finger (my index finger) over the same spot and the sound was still no longer audible until I moved my index finger to another location.  So, I was able to find the "sweet spot" to place the tape on the grille of the intake fan in front.

Every rig does not have the radiator type heat sinks in the exact same location on every chip.  Some could be off or aligned in a certain way after manufacturing that allows for a whistling sound as wind is sucked in between the fins of the heat sinks when they are positioned just right.  Since every rig does not have heat sinks in the exact same location and the exact same size [varying by thousandths of an inch]... this whistling noise is audible only on a small percentage of rigs that have these heat sinks aligned just right to allow for this audible noise.

This is why I feel a small piece of tape is sufficient to reduce the amount of air across particular heat sink(s) causing the noise.  I noticed one miner had placed a piece of foam on the shelf in front of the fan to reduce the noise because that just happened to be the location on his particular S7 where heatsink fins were aligned just right to allow for the whistling noise.  The location of where the wind rushes in across heatsinks will vary from one rig to another more than likely.

[BitAurum]

I got an email from BITMAIN that my order is paid and preparing for shipment.

Its Batch 8 :-( but I paid 1557.55 for it (excluding DHL 44$)

wat lucky you, I havent heard anything.  I wish it would ship, its already -10celcius here, and my garage is cold

-10c ... wow I wish I have your kind of weather to maximize the life of these S7s

I wish I had that kind of weather.
@citronick, What's the electricity rates at the location you live?

The electricity rates here is expensive SGD$0.21kwh or about SGD$175 per S7 per month. SGD/USD ROE 1.4

Ouch. Ouch. That looks very expensive. It would be cheaper for you to get your Antminer's hosted.

[willi9974]

Hello,

if someone had left a coupon, I'd like to buy an S7. it would be a very nice Christmas gift for me...

Bitmain Account: willi9974
Mailadresse: ziegler.christian@gmx.net

Best Regards and happy mining
Willi