My second ZEC + XMR+ ETH thread builds info links thoughts and photos.

[xleejohnx]

So, can i ask which pool most of you here are using for ZEC?  I have been on flypool since the start and the payouts are very quick and reliable. However, I am beginning to wonder about what seems like a pretty big hash-rate difference as reported on their dashboard vs what I see directly in Claymore.  My 2 rigs are currently showing 1,050 S/s consistently but my avg hash-rate at flypool is around 960. Not only that, but the range of reported rates is still all over the place on flypool. In the last 5 hours alone, it showed a high of 1130 and a low of 770... all this time both rigs were at full capacity.  I don't have a huge problem with the spikes as long as the average H/R is being recognized correctly, but it seems to be about 10% short.

Is this normal?  Wondering if I should try Dwarfpool or Suprnova as both seem to be getting some love in other threads I've read.

I recently switched from flypool to suprvova, since I've seen reports ( probably here ), as a test. It will take a few days to see

I may switch on the weekend.

@ LoneRangir As a complete aside please watch for your package I sent It has a holiday surprise gift.

@GabryRox your package should arrive today.

it isnt the pool thats the problem..
even at nicehash with claymore its all over the place ill be at 700 one min then 1300 the next

i only found that optiminer gives the right amount more consistent than claymore but it is slower than claymore anywhere from 20-50 sol/s

[GabryRox]

Happy weekend everyone!  I have a weird issue that is occurring on my 2nd mining rig and was wondering if anyone had experienced similar and/or had any suggestions on what to tweak to try and fix it.  Here's the scenario...

Rig Details:
- i4790k CPU
- ASRock H81 Pro BTC R2 Mobo
- 16GB RAM (2x8)
- Win7 Pro
- 16 GB Virtual Memory
- 1200W Plat PSU
- Claymore ZEC Miner v8

I had 2 MSI 470's running for 3-4 days very stably.  With no tweaks at all, were running about 160 S/s.  After undervolting and setting core/mem clocks to 1300/1900, they were producing about 170-175 S/s.  I had an issue with strapping the first GPU, so reverting back to original BIOS.

After the molex cables from Phil arrived yesterday, I hooked up the 3rd GPU, a Sapphire 470 8GB.  This also ran fine, providing about 180 S/s with no mods (but it comes factory over-clocked).  In addition, the 2 MSI 470's were still running at previous speeds.

The problem started after I hooked up the 4th GPU, another MSI 470.  While my system recognized it fine, after running Claymore for a while, I realized that the hash-rate on all 4 GPUs had dropped.  Now, the 3 MSI's are barely getting 150 and the Sapphire about 155... so, all are about 25 S/s short.  Even stranger, when I set the core/clock speeds of the MSIs to 1300/1900 in afterburner, it has no apparent effect on speeds.

I am using the exact same config file with Claymore v8 as I am on my first rig and all other settings seem to also be inline, but all 4 cards on rig #2 are running about 25 S/s slower than they should be since I added the 4th GPU.  I double checked virtual memory and it is set to 16GB just like rig #1, so not sure what else to check.

Not sure this matters, but I have the 4 GPU's plugged into slots 1, 3, 4, & 5 (all x1 slots).  Slot #2 in the x16 slot and although Phil sent me a ribbon riser, I still need to figure out how to connect it given the design of my rig.  So, after running with USB powered risers in slots 1 & 3 stably, I added the Sapphire to slot 4 and then the 3rd MSI to slot 5.

Anybody seen anything like this before on this or similar Mobo?  I know there are tons of people running this Mobos at full speeds with 6 GPUs, so I must be missing something.  Any suggestions would be highly welcomed.

[LoneRangir]

Happy weekend everyone!  I have a weird issue that is occurring on my 2nd mining rig and was wondering if anyone had experienced similar and/or had any suggestions on what to tweak to try and fix it.  Here's the scenario...

Rig Details:
- i4790k CPU
- ASRock H81 Pro BTC R2 Mobo
- 16GB RAM (2x8)
- Win7 Pro
- 16 GB Virtual Memory
- 1200W Plat PSU
- Claymore ZEC Miner v8

I had 2 MSI 470's running for 3-4 days very stably.  With no tweaks at all, were running about 160 S/s.  After undervolting and setting core/mem clocks to 1300/1900, they were producing about 170-175 S/s.  I had an issue with strapping the first GPU, so reverting back to original BIOS.

After the molex cables from Phil arrived yesterday, I hooked up the 3rd GPU, a Sapphire 470 8GB.  This also ran fine, providing about 180 S/s with no mods (but it comes factory over-clocked).  In addition, the 2 MSI 470's were still running at previous speeds.

The problem started after I hooked up the 4th GPU, another MSI 470.  While my system recognized it fine, after running Claymore for a while, I realized that the hash-rate on all 4 GPUs had dropped.  Now, the 3 MSI's are barely getting 150 and the Sapphire about 155... so, all are about 25 S/s short.  Even stranger, when I set the core/clock speeds of the MSIs to 1300/1900 in afterburner, it has no apparent effect on speeds.

I am using the exact same config file with Claymore v8 as I am on my first rig and all other settings seem to also be inline, but all 4 cards on rig #2 are running about 25 S/s slower than they should be since I added the 4th GPU.  I double checked virtual memory and it is set to 16GB just like rig #1, so not sure what else to check.

Not sure this matters, but I have the 4 GPU's plugged into slots 1, 3, 4, & 5 (all x1 slots).  Slot #2 in the x16 slot and although Phil sent me a ribbon riser, I still need to figure out how to connect it given the design of my rig.  So, after running with USB powered risers in slots 1 & 3 stably, I added the Sapphire to slot 4 and then the 3rd MSI to slot 5.

Anybody seen anything like this before on this or similar Mobo?  I know there are tons of people running this Mobos at full speeds with 6 GPUs, so I must be missing something.  Any suggestions would be highly welcomed.

I have to go inside AMD WattMan from time to time after the cards heat up and toggle 'voltage control' on each card. This only needs to be done on my W7 boxes, the W10 boxes are fine.

[GabryRox]

Thanks Lone!  Amazingly, it seems like just opening up Wattman has resolved this issue.  When I opened the AMD utility, I went to the Wattman tab for my first GPU.  The Voltage control was set to Auto so I toggled it to Manual.  But either right before or right around the time i did this (before clicking Apply, mind you), the speed started to increase on all 4 GPUs... pretty much to their expected rate.  I went ahead and applied the change to manual on all 4 cards and they are now running at the expected pre-overclocking speed.

Out of curiosity, is there any downside to leaving the Voltage control toggled to Manual?

Thanks again for the tip!

[xleejohnx]

Happy weekend everyone!  I have a weird issue that is occurring on my 2nd mining rig and was wondering if anyone had experienced similar and/or had any suggestions on what to tweak to try and fix it.  Here's the scenario...

Rig Details:
- i4790k CPU
- ASRock H81 Pro BTC R2 Mobo
- 16GB RAM (2x8)
- Win7 Pro
- 16 GB Virtual Memory
- 1200W Plat PSU
- Claymore ZEC Miner v8

I had 2 MSI 470's running for 3-4 days very stably.  With no tweaks at all, were running about 160 S/s.  After undervolting and setting core/mem clocks to 1300/1900, they were producing about 170-175 S/s.  I had an issue with strapping the first GPU, so reverting back to original BIOS.

After the molex cables from Phil arrived yesterday, I hooked up the 3rd GPU, a Sapphire 470 8GB.  This also ran fine, providing about 180 S/s with no mods (but it comes factory over-clocked).  In addition, the 2 MSI 470's were still running at previous speeds.

The problem started after I hooked up the 4th GPU, another MSI 470.  While my system recognized it fine, after running Claymore for a while, I realized that the hash-rate on all 4 GPUs had dropped.  Now, the 3 MSI's are barely getting 150 and the Sapphire about 155... so, all are about 25 S/s short.  Even stranger, when I set the core/clock speeds of the MSIs to 1300/1900 in afterburner, it has no apparent effect on speeds.

I am using the exact same config file with Claymore v8 as I am on my first rig and all other settings seem to also be inline, but all 4 cards on rig #2 are running about 25 S/s slower than they should be since I added the 4th GPU.  I double checked virtual memory and it is set to 16GB just like rig #1, so not sure what else to check.

Not sure this matters, but I have the 4 GPU's plugged into slots 1, 3, 4, & 5 (all x1 slots).  Slot #2 in the x16 slot and although Phil sent me a ribbon riser, I still need to figure out how to connect it given the design of my rig.  So, after running with USB powered risers in slots 1 & 3 stably, I added the Sapphire to slot 4 and then the 3rd MSI to slot 5.

Anybody seen anything like this before on this or similar Mobo?  I know there are tons of people running this Mobos at full speeds with 6 GPUs, so I must be missing something.  Any suggestions would be highly welcomed.

Check temps make sure thermals are good

Sometime when you run something in the x16 it gets all the resources it needs
then everything left over is divided out
You can change in bios of mobo an make all slots Gen1
just to make sure it isn't bugging out
I always change it even if it isn't needed


Edit: Seems you fixed it nevermind on this then lol

[LoneRangir]

Thanks Lone!  Amazingly, it seems like just opening up Wattman has resolved this issue.  When I opened the AMD utility, I went to the Wattman tab for my first GPU.  The Voltage control was set to Auto so I toggled it to Manual.  But either right before or right around the time i did this (before clicking Apply, mind you), the speed started to increase on all 4 GPUs... pretty much to their expected rate.  I went ahead and applied the change to manual on all 4 cards and they are now running at the expected pre-overclocking speed.

Out of curiosity, is there any downside to leaving the Voltage control toggled to Manual?

Thanks again for the tip!

The mere act of toggling it snaps my cards out of the funk.  Some I end up turning it 'off' and some I end up turning it 'on.  Makes no difference, just the act of fiddling with it.  This does not appear to happen on W10, as far as I can tell.

[GabryRox]

Happy weekend everyone!  I have a weird issue that is occurring on my 2nd mining rig and was wondering if anyone had experienced similar and/or had any suggestions on what to tweak to try and fix it.  Here's the scenario...

Rig Details:
- i4790k CPU
- ASRock H81 Pro BTC R2 Mobo
- 16GB RAM (2x8)
- Win7 Pro
- 16 GB Virtual Memory
- 1200W Plat PSU
- Claymore ZEC Miner v8

I had 2 MSI 470's running for 3-4 days very stably.  With no tweaks at all, were running about 160 S/s.  After undervolting and setting core/mem clocks to 1300/1900, they were producing about 170-175 S/s.  I had an issue with strapping the first GPU, so reverting back to original BIOS.

After the molex cables from Phil arrived yesterday, I hooked up the 3rd GPU, a Sapphire 470 8GB.  This also ran fine, providing about 180 S/s with no mods (but it comes factory over-clocked).  In addition, the 2 MSI 470's were still running at previous speeds.

The problem started after I hooked up the 4th GPU, another MSI 470.  While my system recognized it fine, after running Claymore for a while, I realized that the hash-rate on all 4 GPUs had dropped.  Now, the 3 MSI's are barely getting 150 and the Sapphire about 155... so, all are about 25 S/s short.  Even stranger, when I set the core/clock speeds of the MSIs to 1300/1900 in afterburner, it has no apparent effect on speeds.

I am using the exact same config file with Claymore v8 as I am on my first rig and all other settings seem to also be inline, but all 4 cards on rig #2 are running about 25 S/s slower than they should be since I added the 4th GPU.  I double checked virtual memory and it is set to 16GB just like rig #1, so not sure what else to check.

Not sure this matters, but I have the 4 GPU's plugged into slots 1, 3, 4, & 5 (all x1 slots).  Slot #2 in the x16 slot and although Phil sent me a ribbon riser, I still need to figure out how to connect it given the design of my rig.  So, after running with USB powered risers in slots 1 & 3 stably, I added the Sapphire to slot 4 and then the 3rd MSI to slot 5.

Anybody seen anything like this before on this or similar Mobo?  I know there are tons of people running this Mobos at full speeds with 6 GPUs, so I must be missing something.  Any suggestions would be highly welcomed.

Check temps make sure thermals are good

Sometime when you run something in the x16 it gets all the resources it needs
then everything left over is divided out
You can change in bios of mobo an make all slots Gen1
just to make sure it isn't bugging out
I always change it even if it isn't needed


Edit: Seems you fixed it nevermind on this then lol

Hey John, thanks for this tips.  Lone's tip did indeed fix my current speed issue, but what you mention about changing the x16 slot to Gen1 in the BIOS might actually solve the other issue I am having.  I don't currently have anything plugged into the x16 slot because I cannot get past post with a USB powered riser plugged in there.  Phil kindly sent me a x16 to x16 ribbon riser, but it isn't long/twistable enough to make work in my current configuration.  So... maybe setting this slot to Gen1 in the BIOS will fix this issue.  Can you provide and tips on how to do this?  Seems that every time i go into BIOS it takes me forever to find things.

[ps_jb]

I used all the same risers for all 6 slots in BTC Pro - everything was good.

[bittawm]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

[philipma1957]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

[bittawm]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I am using some reference rx480s some reference r470s and some nitro rx470s, has anyone managed to fix it?

Cheers

[ps_jb]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

[LoneRangir]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

Is it the card with the monitor hooked up to it? If so, put the monitor on a different card

[philipma1957]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

Is it the card with the monitor hooked up to it? If so, put the monitor on a different card

 

yeah sapphire and xfx have this issue. 

swap the monitor cable  from card to card.

also if you are an hdmi cable try using this

https://www.amazon.com/Cable-Matters-Gold-Plated-DisplayPort/dp/B004C9P9TM/ref=sr_1_2?


or if the card has a dvi  jack

https://www.amazon.com/dp/B014I8UU2W/ref=sr_ph_1?


all miners should have a few of the above  they have helped me with black screen issues and with the dreaded 4mh bug

[Prelude]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

Make sure crossfire and ULPS are disabled. Regedit is the best way to go.

[fiscorcle]

Phil , how do you sell your ZEC ?
do you sell everything ? with a feature like auto-sell , or do you follow the charts ?

I sell the ZEC the moment it is in my exchange account. I reckon it will drop to 60-70% of current price due to the increased supply.

I stopped mining zec and went to Nicehash multi.
I'm getting the same pay all the way around right now (zec/xmr/eth)
And it's straight into my btc account

the latest v1.7.3.6 have now integrated Claymore Zcash miner v8 !!!

what this means is...... we have Claymore's magic miner running as long as Zacsh is profitable, AND when Zcash is not profitable anymore... NH miner will switch to next profitable algo..... sounds like we have a winner here.

That's very good news ! Sadly the great profitability of ZCash calmed down, so I now switched it off. I'll maybe just restart the RX 470 in some days.

Was wanting to do the same thing with 470's. But with the downturn in Zec all the sudden I don't know if it is worth it now to start. 

[bittawm]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

Make sure crossfire and ULPS are disabled. Regedit is the best way to go.

and how do we do that mate?

[bittawm]

i am using the same build as phills. however I am having some trouble

I am having trouble having all 4 cards to mine at full speed, when all 4 of them are plugged in one gpu always mines at 4mhs instead of 24mhs, i have tested all cards individually and all work, i have testeded all slots individually and they work,
please please help me kind souls

that bug has occurred with a few of us.

what cards do you use.

I have exactly the same bug.

MB - Z97 GAMING 5. All cards are RX 480 Nitro+ (on powered risers)

Tried everything - always one card  is 4MH/s

Is it the card with the monitor hooked up to it? If so, put the monitor on a different card

 

yeah sapphire and xfx have this issue. 

swap the monitor cable  from card to card.

also if you are an hdmi cable try using this

https://www.amazon.com/Cable-Matters-Gold-Plated-DisplayPort/dp/B004C9P9TM/ref=sr_1_2?


or if the card has a dvi  jack

https://www.amazon.com/dp/B014I8UU2W/ref=sr_ph_1?


all miners should have a few of the above  they have helped me with black screen issues and with the dreaded 4mh bug

I am having both black screens and 4mhs bug, so sad

[ps_jb]

yeah sapphire and xfx have this issue. 

swap the monitor cable  from card to card.

also if you are an hdmi cable try using this

https://www.amazon.com/Cable-Matters-Gold-Plated-DisplayPort/dp/B004C9P9TM/ref=sr_1_2?


or if the card has a dvi  jack

https://www.amazon.com/dp/B014I8UU2W/ref=sr_ph_1?


all miners should have a few of the above  they have helped me with black screen issues and with the dreaded 4mh bug

I did not check is it related with monitor or not. But when I have a HDMI dongle - I have the same issue

Do you think it is cable?

[ps_jb]

Make sure crossfire and ULPS are disabled. Regedit is the best way to go.

They were disable from the beginning

Thank you!