exsexs1
Newbie
Offline
Activity: 31
Merit: 0
|
|
November 08, 2017, 10:22:30 PM |
|
@blissz: could we modify voltage with software? I connected to D3 with SSH, and I can change some settings in cgminer and cgminer.conf, but I don't know what is the best voltage value.
|
|
|
|
bodrumair
Newbie
Offline
Activity: 31
Merit: 0
|
|
November 09, 2017, 10:58:53 AM |
|
changing the hashing algo strongly needed for this device. x11(coins) is insufficient as of today
|
|
|
|
blissz (OP)
|
|
November 09, 2017, 06:40:29 PM |
|
@blissz: could we modify voltage with software? I connected to D3 with SSH, and I can change some settings in cgminer and cgminer.conf, but I don't know what is the best voltage value.
I expect it's possible but didn't find the right knobs yet to do so. It would be way more convenient compared to the hard mod...
|
|
|
|
kats2005
Newbie
Offline
Activity: 16
Merit: 0
|
|
November 09, 2017, 07:06:11 PM |
|
after under volting to 7.1v is it ok to set a higher clock value other than 430mhz. if so, which value would be most optimal for this under volted "7.1v" miner ?
|
|
|
|
exsexs1
Newbie
Offline
Activity: 31
Merit: 0
|
|
November 09, 2017, 08:05:22 PM |
|
@blissz: could we modify voltage with software? I connected to D3 with SSH, and I can change some settings in cgminer and cgminer.conf, but I don't know what is the best voltage value.
I expect it's possible but didn't find the right knobs yet to do so. It would be way more convenient compared to the hard mod... Antminer S series had voltage/freq/timing table. If so have same table, it would be easy to set better efficiency.
|
|
|
|
detonyle
Member
Offline
Activity: 140
Merit: 10
|
|
November 10, 2017, 07:12:45 AM |
|
Very nice job Dude !!
do you have another picture of the soldering of potentiometer on the r80 slot?
Thanks
|
|
|
|
cryptonitro
|
|
November 10, 2017, 09:00:10 AM |
|
did someone as the magic skill to shutdown the 100% default fan on every reboot or setting change ? this make me crazy
|
The only project make me believe ... Holochain
|
|
|
DIMESECO
Newbie
Offline
Activity: 15
Merit: 0
|
|
November 10, 2017, 04:46:14 PM |
|
Hi, i'm also an owner of some Antminer D3 devices. My skills are software engineering, but my world is microsoft based and not linux. But i have installed cygwin and unpacked the new firmware (initramfs.bin.SD) to a folder to inspect all files. My idea is to get sgminer (from new Baikal X10) up and running. That would be very cool, but i don't know where to start. What i can see is, that Antminer runs cgminer 4.9.0 and Baikal runs sgminer... Is this possible? Anybody else an idea? Here is the unpacked Folder from last firmware update. https://mega.nz/#!JhhEhBqR!WWQEH3k-6meKovCf-snZmf8Wo-1VaMEwiS2tfOyLNgQ
|
|
|
|
blissz (OP)
|
|
November 11, 2017, 12:47:46 AM |
|
did someone as the magic skill to shutdown the 100% default fan on every reboot or setting change ? this make me crazy
This is annoying me as well. There is check in cgminer for > 5000rpm when starting up. I might build a simple 555 circuit to fake the RPM, because this fan startup noise is really annoying
|
|
|
|
blissz (OP)
|
|
November 11, 2017, 12:49:34 AM |
|
Hi, i'm also an owner of some Antminer D3 devices. My skills are software engineering, but my world is microsoft based and not linux. But i have installed cygwin and unpacked the new firmware (initramfs.bin.SD) to a folder to inspect all files. My idea is to get sgminer (from new Baikal X10) up and running. That would be very cool, but i don't know where to start. What i can see is, that Antminer runs cgminer 4.9.0 and Baikal runs sgminer... Is this possible? Anybody else an idea? Here is the unpacked Folder from last firmware update. https://mega.nz/#!JhhEhBqR!WWQEH3k-6meKovCf-snZmf8Wo-1VaMEwiS2tfOyLNgQI guess that;s quite a challenge. The interface to the d3 board is a serial connection. Not sure about the baikal. If we could get the source for the d3 cgminer that would really open up possibilies... So if one with access to this reads this....
|
|
|
|
exsexs1
Newbie
Offline
Activity: 31
Merit: 0
|
|
November 11, 2017, 08:26:58 AM |
|
I guess that;s quite a challenge. The interface to the d3 board is a serial connection. Not sure about the baikal. If we could get the source for the d3 cgminer that would really open up possibilies... So if one with access to this reads this.... cgminer D3 source at here: https://github.com/bitmaintech/cgminer-dash
|
|
|
|
cryptonitro
|
|
November 11, 2017, 07:20:44 PM |
|
@blissz can you have a better indication (drawing or other pics) for where to fix 25k ohm potentiometer and what you mean for replace R80 ?
|
The only project make me believe ... Holochain
|
|
|
blissz (OP)
|
|
November 11, 2017, 08:52:59 PM |
|
@blissz can you have a better indication (drawing or other pics) for where to fix 25k ohm potentiometer and what you mean for replace R80 ?
You need to remove the R80 resistor first and put the potentiometer wired to the 2 "solder islands" of where the R80 was fixed.
|
|
|
|
blissz (OP)
|
|
November 11, 2017, 09:03:28 PM Last edit: November 11, 2017, 10:05:11 PM by blissz |
|
I guess that;s quite a challenge. The interface to the d3 board is a serial connection. Not sure about the baikal. If we could get the source for the d3 cgminer that would really open up possibilies... So if one with access to this reads this.... cgminer D3 source at here: https://github.com/bitmaintech/cgminer-dashThis is good stuff. Thanks for this. I checked the source and it's legit. I took a quick look at the code and I do see lots of possibilities: 1) adjust ASIC voltage from software 99% YES 2) fix the fan startup speed / fan speed limits YES 3) change the algorithm MAYBE YES. I found something really interesting in the initialization of the ASICS. It seems like there is something build in to the asics to support multiple algorithms, which can be unlocked by the firmware. As I only own one D3 miner and need to spend lot's of time on implementing it I consider a few things: - don't bother modding the d3 even further. - supply a miner binary with the mods and add a fee percentage - make the mods, show it in a video / or whatever and ask for a donation before releasing it to the public.
|
|
|
|
exsexs1
Newbie
Offline
Activity: 31
Merit: 0
|
|
November 11, 2017, 10:09:30 PM |
|
I guess that;s quite a challenge. The interface to the d3 board is a serial connection. Not sure about the baikal. If we could get the source for the d3 cgminer that would really open up possibilies... So if one with access to this reads this.... cgminer D3 source at here: https://github.com/bitmaintech/cgminer-dashThis is good stuff. Thanks for this. I checked the source and it's legit. I took a quick look at the code and I do see lots of possibilities: 1) adjust ASIC voltage from software 99% YES 2) fix the fan startup speed / fan speed limits YES 3) change the algorithm MAYBE YES. I found something really interesting in the initialization of the ASICS. It seems like there is something build in to the asics to support multiple algorithms, which can be unlocked by the firmware. As I only own one D3 miner and need to spend lot's of time on implementing it I consider a few things: - don't bother modding the d3 even further. - supply a miner binary with the mods and add a fee percentage - make the mods, show it in a video / or whatever and ask for a donation before releasing it to the public. @blissz: pm. me! I've some ideas modding D3, and I have questions.
|
|
|
|
stugots2
Full Member
Offline
Activity: 224
Merit: 102
Too Many Miners Not Enough Electricity
|
|
November 11, 2017, 10:48:15 PM |
|
with profits down, I'd mod LOL
|
|
|
|
toefu
Newbie
Offline
Activity: 36
Merit: 0
|
|
November 12, 2017, 12:35:38 AM |
|
honestly, if someone can write a customized miner for the d3 to mine different algo's, i'm sure the community would have no issues paying a mining fee.
good luck on the research guys.
|
|
|
|
kats2005
Newbie
Offline
Activity: 16
Merit: 0
|
|
November 12, 2017, 06:02:59 AM |
|
I managed to implement the hardware undervolting Mod and I must say it works like magic. Currently doing 6.9V @ 437MHZ giving me about 15.3GH with no HW errors I think if D3 is unlocked to other algos, this would be like having an early xmas coz bitmain fooled so many pple by over selling these machines and they are doing the same thing now to L3+ So if for example i can use my D3 on Scrypt. It would mean a vast number of pple will not order from bitmain but simply change algo of the D3 they already own which would put bitmain in check atleast for a short while. I wouldnt mind paying for these software mods just to stick it up to bitmain
|
|
|
|
blissz (OP)
|
|
November 12, 2017, 07:04:39 AM |
|
I managed to implement the hardware undervolting Mod and I must say it works like magic. Currently doing 6.9V @ 437MHZ giving me about 15.3GH with no HW errors I think if D3 is unlocked to other algos, this would be like having an early xmas coz bitmain fooled so many pple by over selling these machines and they are doing the same thing now to L3+ So if for example i can use my D3 on Scrypt. It would mean a vast number of pple will not order from bitmain but simply change algo of the D3 they already own which would put bitmain in check atleast for a short while. I wouldnt mind paying for these software mods just to stick it up to bitmain Good to hear the hardware mod works for you as well!
|
|
|
|
lhajnal
Newbie
Offline
Activity: 18
Merit: 0
|
|
November 12, 2017, 09:47:24 AM |
|
I am waiting, that I check it, but not received yet the november batch. I hope, that will be a new firmware, which can use more algo. Because this is a s##t now.
|
|
|
|
|