[ANN] Technobit HEX16B(Bitfury based) 16 chip board design

[turtle83]

This guy is a nightmare in 3-D!
Fuck technobit.eu

+1 .

I am glad that i got my boards and they work well, and looks like good build quality... but if given the chance to go back in time... i would stop myself from making this order.

So you are +1 .............
With a man that did ordered assembly service without having chips to ship and then
ordering 2 other orders without reading that it is December shipment.

No. I don't know his story... +1 to the fact that you were a nightmare to deal with... and treat buyers like shit.

[1714947264]

1714947264

[1714947264]

1714947264

[1714947264]

1714947264

[1714947264]

1714947264

[1714947264]

1714947264

[marto74]

No I do not treat nobody like shit.
We just have troubles in production and did not have personnel to deal with customers.
Now We have, will see if it works better

Best Martin

[cbrboot]

Why are you people bashing technobit?
Even my second order went perfect, maby a bit late but then again it's better than pre-order!
In total i have ordered more than 10 miners, in the end the only thing that counts is that it works.

So keep in mind, this is still better than pre-order. And for all the other people who are not sure what they are ordering, just ask it before you buy... seems a logic thing to do right?

[berny81]

in the end i have marto74 attention with PM, he have certainly to improve customers relationship but DON'T tell him scammer or other strong negative word, he is a serious person.
Expose your problem in a clean manner and be patient, he answer you in the same manner and solve your problem in the best way.

i have unlucky experience with my order but my opinion of technobit.eu and marto74 is POSITIVE

[Pentium100]

I had no problems with Technobit apart from the software. My order shipped on time and the devices work. My previous order was with BFL and compared to that, even with the time I could not mine because I could not figure out how to build the patched cgminer, Technobit comes out ahead by about 7 months.

[Melb]

Why are you people bashing technobit?
Even my second order went perfect, maby a bit late but then again it's better than pre-order!
In total i have ordered more than 10 miners, in the end the only thing that counts is that it works.

So keep in mind, this is still better than pre-order. And for all the other people who are not sure what they are ordering, just ask it before you buy... seems a logic thing to do right?

So whats the score Martin? Where do I stand with order HHAHDTTXC? Which should have been shipped UPS (according to you) 2 weeks ago? You will not answer me - why? I am pleading with you in order to be sympathetic for your cause but you refuse to communicate! So you have my money I have no goods is that it? Is that what Technobit.eu is all about? Shouldn't you want more for your reputation and your business? How can anyone placing an order for 'January delivery' be confident they will receive anything from you when you have so many unfulfilled orders from October/November? Get a grip you are talking rubbish Marto...


Melb

[Melb]

Why are you people bashing technobit?

Simple to answer.. Not everyone has a good experience like you... I had 1 order which was great! the items were good and well built... The second order which was supposed to have been sent UPS to me (2 weeks ago) after a botched courier via speedy had not materialized (funny how Speedy seem to have 'canceled' so many Nanofury orders - they must have X-Ray specs!) - and I have no idea where this order is - if indeed it ever existed... I have PM'd Marto several times - left many massages within these forum posts but Marto doesn't respond  to PM's or otherwise... I wonder why that would be?

Melb
 

[Gator-hex]

(funny how Speedy seem to have 'canceled' so many Nanofury orders - they must have X-Ray specs!)

You don't need X-ray specs the tape says "TechnoBit" in giant letters all over the box!  

[Melb]

(funny how Speedy seem to have 'canceled' so many Nanofury orders - they must have X-Ray specs!)

You don't need X-ray specs the box tape says "TechnoBit" all over it. 

I guess it must have said 'Technobit Nanofuryl' on it because it is very odd just how many of those Nanofury orders seemed to have been canceled by Speedy - apparently... Someone is not being very honest here...

Melb

[cbrboot]

Why are you people bashing technobit?

Simple to answer.. Not everyone has a good experience like you... I had 1 order which was great! the items were good and well built... The second order which was supposed to have been sent UPS to me (2 weeks ago) after a botched courier via speedy had not materialized (funny how Speedy seem to have 'canceled' so many Nanofury orders - they must have X-Ray specs!) - and I have no idea where this order is - if indeed it ever existed... I have PM'd Marto several times - left many massages within these forum posts but Marto doesn't respond  to PM's or otherwise... I wonder why that would be?

Melb
 

Well, now that you posted this, give Marto a day to respond....
If he really does not reply to this then you may be right and then it's a good question if anyone needs to doubt on ordering again i assume.

[uberdag]

How to apply cgminer patch from technoBTCit

Code:

1. mkdir cgminer
2. cd cgminer
3. wget https://github.com/ckolivas/cgminer/archive/v3.8.1.tar.gz
4. tar -xvf v3.8.1.tar.gz
5. cd cgminer-3.8.1
6. wget https://www.dropbox.com/s/5suzudn2t06087u/2e9afa38e39678a5dc5bf8be6d20baf1849b548c.patch
7. patch -p1 < 2e9afa38e39678a5dc5bf8be6d20baf1849b548c.patch
8. ./autogen.sh --enable-avalon --enable-bitfury --enable-hexminerb --enable-bflsc 
9. make

You can skip step 6 if can copy the file to 3.8.1 folder or upload yourself the patch

i get the error:
bash: ./autogen.sh: No such file or directory
on step 8
xubuntu 13.10

[Zich]

Hello ,

Your shipment have been detained at customs because the devices are considered higher than normal USB port and also can not be taken for personal use of an individual in these countries. This is because they have a greater number and variety of standard flash drive.

Can only be sent to a company with pro-forma invoice. Please let us know if you can specify to both company receiving shipments and send us the adjusted pro-forma invoices .

Please your urgent response and assistance , otherwise if items will not be cleared .



Regards,

Iliana Ivanova
Responsible call center of Sofia and Plovdiv
SPEEDY
Sofia ul.Abagar , based Somat
www.speedy.bg

[uberdag]

also what does make do... mine says  no files specified
make: *** No targets specified and no makefile found.  Stop.

[Zich]

also what does make do... mine says  no files specified
make: *** No targets specified and no makefile found.  Stop.

Are you get the source from git?
You need to run autogen first before doing make. so if autogen fail you need to find why?
How about try to re download to other folder

[bitminterlt]

I posted this a few pages before with no response again. Its a December order, but there hasn't been any charges for shipping and I don't want anything to hold it up at all.....

Can you please check on my orders:

DRTYHYCSI
and
AXPOLDEBC

Both ordered on 11/21/13 and have not been asked to pay for shipping yet, and I dont want anything delayed on my part. I have also asked your support on the website a few times without a single response from ANYONE!!

Can you please tell me when I should expect these items to ship out and what my options are for the nano ones? I ordered 4 units but they are assembly and you need my chips. BUT i know have any so I think I would need to return those ones unless you can offer chips too

Thanks and PLEASE Get back to me on this....

[uberdag]

also what does make do... mine says  no files specified
make: *** No targets specified and no makefile found.  Stop.

Are you get the source from git?
You need to run autogen first before doing make. so if autogen fail you need to find why?
How about try to re download to other folder

got it from actual klovis site... used to getting the 86-64 built ones...  anyhow i got the one you had ref... autogen worked but now make says no targets error.

thanks again for all your help

[Zich]

Hello Zich

I am wondering if you might do me a fav (random guy from the interwebz ask for favs, never good SORRY ! :/)

Could you post this to the Thread https://bitcointalk.org/index.php?topic=307897.260

My 1st week December HEX16B boards arrived yesterday. No issues, I ordered via pay pal, they arrived within stated time frame. All good in that regards, in defense of techno bit; in their November post they did state that they needed to change their shipping company and that they were employing someone to do Customer Services, so to anyone reading, give them time, no scam here.  

Ok I did not originally order the TP-link router and planned to hook them up to my existing windows 7 miner. So using windows 7 64 bit, i installed the Technobit Drivers http://technobit.eu/index.php?controller=attachment&id_attachment=9 (could it be as simple as currently there are no 64bit drivers?) Hooked in the miner, and it does not appear to be working. Now I believe the proxy is working as I can see the requests for new jobs from eu-stratum.btcguild, but the actual miner itself does not seem to connect to the hex miner. The only stat that seems to count up is blocks (which has got to a 2) :/ When on the Debug tab i can see that i get "access denied to com port 4" then i see lots of GetWork and SerialWrites but nothing seems to be hashing. So i think it is getting jobs from the proxy but not accessing the hardware? OK i am hoping this is the windows 7 64 driver problem that would make a lot of sense given the above

Using the following settings
Com4
ICA = 540Mh/s
Chip Count = 16
Timeout = 10sec
Voltage 0.830

I have ordered the TP link router with a powered hub, this will be arriving tomorrow. I would like to know however if i can get it working on windows to test it for 24 hours.

Azaz

Maybe some of us that use HEXMINER under windows can give some help since i using TL-MR3020 only 

[Gator-hex]

the actual miner itself does not seem to connect to the hex miner.

It might be the problem I ran into today of power leaking back to the USB and if the USB port has surge protection it cuts it off.

Check out the Hex16A Tutorial too http://youtu.be/l9SgoVm16Sw?t=3m43s as that show the windows setup.

[uberdag]

i also get can not find cgminer when running in the correct dir
sudo ./cgminer --hexminerb-voltage 900 --hexminerb-options 16:540

[Zich]

i also get can not find cgminer when running in the correct dir
sudo ./cgminer --hexminerb-voltage 900 --hexminerb-options 16:540

You still need to make which is fail.
if you get the source from ck then you need to run

Code:

CFLAGS="-O2 -Wall -march=native" ./configure <options>

after autogen.

I wonder if you installed all required library?

Code:

1. sudo aptitude update
2. sudo aptitude install libudev-dev libusb-1.0-0-dev libfox-1.6-dev
3. sudo aptitude install autotools-dev autoconf automake libtool libncurses-dev curl libcurl4-openssl-dev libjansson-dev uthash-dev make pkg-config yasm