alibert
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 05, 2014, 12:16:45 PM |
|
How do you use the cgminer API? It seems broken: root@HEX16A:/tmp# nc 127.0.0.1 4028 version STATUS=E,When=1396700148,Code=14,Msg=Invalid command,Description=cgminer 4.2.2|root@HEX16A:/tmp# root@HEX16A:/tmp#
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 05, 2014, 12:19:13 PM |
|
How do you use the cgminer API? It seems broken: root@HEX16A:/tmp# nc 127.0.0.1 4028 version STATUS=E,When=1396700148,Code=14,Msg=Invalid command,Description=cgminer 4.2.2|root@HEX16A:/tmp# root@HEX16A:/tmp#
just run command
|
|
|
|
eestimees
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 06, 2014, 08:36:35 AM |
|
Hi what could be the reason for device shutoff? cgminer version 4.2.2 - Started: [2014-04-06 11:24:20] -------------------------------------------------------------------------------- (5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s ST: 3 SS: 0 NB: 1 LW: 152 GF: 0 RF: 0 Connected to stratum.btcguild.com diff 256 with stratum as user xxx Block: 73657c86... Diff:6.12G Started: [11:24:20] Best share: 0 -------------------------------------------------------------------------------- [U]SB management [P]ool management [S]ettings [D]isplay options [Q]uit 0: HEX8 0 : 260 1000/ 800mV | A:0 R:0/0.00% HW:0/0.00% WU:0.0/m -------------------------------------------------------------------------------- [2014-04-06 11:24:07] Started cgminer 4.2.2 [2014-04-06 11:24:14] Probing for an alive pool [2014-04-06 11:24:19] Pool 1 difficulty changed to 2 [2014-04-06 11:24:20] Pool 0 difficulty changed to 2 [2014-04-06 11:24:20] Switching to pool 1 stratum+tcp://stratum.btcguild.com:3333 - first alive pool [2014-04-06 11:24:20] Pool 1 difficulty changed to 256 [2014-04-06 11:24:20] Network diff set to 6.12G [2014-04-06 11:24:20] Pool 2 difficulty changed to 2 [2014-04-06 11:24:20] Pool 0 stratum+tcp://stratum.btcguild.com:3333 alive, testing stability [2014-04-06 11:24:20] Pool 0 difficulty changed to 256 [2014-04-06 11:24:20] Switching to pool 0 stratum+tcp://stratum.btcguild.com:3333 [2014-04-06 11:24:20] Pool 2 difficulty changed to 256 [2014-04-06 11:24:25] API running in IP access mode on port 4028 (11) [2014-04-06 11:26:22] HEX80: Idle for more than 60 seconds, declaring SICK! [2014-04-06 11:26:22] HEX80: Attempting to restart [2014-04-06 11:26:22] HEX8 0 Send config failed [2014-04-06 11:26:22] HEX8 0 failure, disabling! When device starts, it submits some work: BTC guild: xxx 0.000 GH/s Accepted share: 560 (90.91%) Stale: 256 / Dupe: 0 / Other: 0 EDIT: Solved - faulty USB cable ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
— eestimees
|
|
|
Gator-hex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 06, 2014, 05:15:47 PM |
|
I had something weird happen with the new 0_3_1 software and the Hex8A1. I've only been using it a few days.
Lost internet, after router rebooted, the Hex16B went back to mining, but the Hex8A1 flashed red/green. They were using as much power, maybe 20W more actually, but no mining effort was appearing at the pool. I SSH into the TP-Link and it's running 85% load instead of the 30% it normally runs.
After I rebooted everything it's back to normal.
|
|
|
|
loshia
Legendary
Offline
Activity: 1610
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 06, 2014, 05:18:37 PM Last edit: April 06, 2014, 05:37:23 PM by loshia |
|
I had something weird happen with the new 0_3_1 software and the Hex8A1. I've only been using it a few days.
Lost internet, after router rebooted, the Hex16B went back to mining, but the Hex8A1 flashed red/green. They were using as much power, maybe 20W more actually, but no mining effort was appearing at the pool. I SSH into the TP-Link and it's running 85% load instead of the 30% it normally runs.
After I rebooted everything it's back to normal.
Did you check memory of tplink? Free ? High constant CPU usage indicates a thread lock Most probably get_work was not awaken for some reason If you are curious you can build cgminer with LOCK_TRacking enabled miner.h And see lock stats output cgminer-api lockstats and check contents of /tmp/cglock file and post that here when something wired happens again Check if corn is enabled on tplink also It should reboot cgminer when it is not submitting work to the pool for some reason every 5 mins or so
|
|
|
|
Moikka2
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 06, 2014, 09:53:48 PM |
|
i keep getting failures on the hex 16A2 the failure keeps happening periodically and hexboard disables and then starts a new one -> might be over 30-50per day. most of the time its ZOMBIE or from faulty to DEAD. re-starting everything sometimes help, but now i'm starting to get the following (tried 3.xx and 4.0.0 and 4.2.2 versions) HEXC failure -> disabling **** glibc detected - cgminer malloc(): memory corruption : 0x012dd718 what wrong? this is the setup im using: 1. git clone https://github.com/ckolivas/cgminer.git2. mv cgminer cgminer-4.2.2 3. cd cgminer-4.2.2 4. git checkout 5ed45a0d7a3bd71ed1b8726e5f1cdac55bf68196 5. wget https://www.dropbox.com/s/1kspms3gw0336du/5ed45a0d7a3bd71ed1b8726e5f1cdac55bf68196.patch 6. patch -p1 < 5ed45a0d7a3bd71ed1b8726e5f1cdac55bf68196.patch 7. ./autogen.sh 8. ./configuration --enable-hexminera --enable-hexminerc (a and c are needed to both be enabled to C-to work) 9. sudo make 10. sudo make install 11. sudo ./cgminer and for settings: --hexminerc-voltage 1080 --hexminerc-options 16:1400 (used the same to enable bflsc (jalapeno) in different folder cgminer-4.2.3 and it works ok all the time.
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 01:39:01 AM |
|
i keep getting failures on the hex 16A2 the failure keeps happening periodically and hexboard disables and then starts a new one -> might be over 30-50per day. most of the time its ZOMBIE or from faulty to DEAD.
re-starting everything sometimes help, but now i'm starting to get the following (tried 3.xx and 4.0.0 and 4.2.2 versions)
HEXC failure -> disabling **** glibc detected - cgminer malloc(): memory corruption : 0x012dd718
what wrong?
Visual check your HEX16C, see if there is any burn component.
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 09:19:47 AM |
|
World fastest USB stick miner ![Cool](https://bitcointalk.org/Smileys/default/cool.gif) ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fs26.postimg.org%2Fqgg1g1seh%2Fbug.jpg&t=665&c=4B6LPKc2rDnLLQ)
|
|
|
|
loshia
Legendary
Offline
Activity: 1610
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 11:24:01 AM |
|
World fastest USB stick miner ![Cool](https://bitcointalk.org/Smileys/default/cool.gif) ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fs26.postimg.org%2Fqgg1g1seh%2Fbug.jpg&t=665&c=4B6LPKc2rDnLLQ) Hey, Disable sysntpd after upgrade that is the problem ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd ![Wink](https://bitcointalk.org/Smileys/default/wink.gif)
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 11:45:14 AM |
|
Hey, Disable sysntpd after upgrade that is the problem ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) Woo, just find out that using sysupgrade.bin, some process that supposed to disable is enable. Thanks loshia ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
loshia
Legendary
Offline
Activity: 1610
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 12:09:25 PM |
|
Hey, Disable sysntpd after upgrade that is the problem ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) Woo, just find out that using sysupgrade.bin, some process that supposed to disable is enable. Thanks loshia ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) for tplink after upgrade type /usr/bin/fix_rc & exit that will disable the junk and reboot router ![Wink](https://bitcointalk.org/Smileys/default/wink.gif)
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 12:22:36 PM |
|
Hey, Disable sysntpd after upgrade that is the problem ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) /etc/init.d/sysntpd disable reboot If it is not tplink just disable it ntpd ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) Woo, just find out that using sysupgrade.bin, some process that supposed to disable is enable. Thanks loshia ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) for tplink after upgrade type /usr/bin/fix_rc & exit that will disable the junk and reboot router ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) Nice ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) I almost reflash using factory.bin ![Roll Eyes](https://bitcointalk.org/Smileys/default/rolleyes.gif) , lucky ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) Thanks loshia ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
Gator-hex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 01:32:49 PM |
|
i keep getting failures on the hex 16A2 the failure keeps happening periodically and hexboard disables and then starts a new one -> might be over 30-50per day. most of the time its ZOMBIE or from faulty to DEAD.
re-starting everything sometimes help, but now i'm starting to get the following (tried 3.xx and 4.0.0 and 4.2.2 versions)
HEXC failure -> disabling **** glibc detected - cgminer malloc(): memory corruption : 0x012dd718
what wrong?
Visual check your HEX16C, see if there is any burn component. You can get random restarts from using USB1 (too slow) or multiple power supplies on a shared USB hub (try a power protected hub or seperate everything) or one of the boards is leaking power on the USB (try taping out the gnd/+5V in the USB cable).
|
|
|
|
Moikka2
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 02:30:51 PM |
|
i keep getting failures on the hex 16A2 the failure keeps happening periodically and hexboard disables and then starts a new one -> might be over 30-50per day. most of the time its ZOMBIE or from faulty to DEAD.
re-starting everything sometimes help, but now i'm starting to get the following (tried 3.xx and 4.0.0 and 4.2.2 versions)
HEXC failure -> disabling **** glibc detected - cgminer malloc(): memory corruption : 0x012dd718
what wrong?
Visual check your HEX16C, see if there is any burn component. You can get random restarts from using USB1 (too slow) or multiple power supplies on a shared USB hub (try a power protected hub or seperate everything) or one of the boards is leaking power on the USB (try taping out the gnd/+5V in the USB cable). about burned component : No Visual problem seen, also works sometimes a while -> so mayby components ok! about the USB -> i have USB2 cables but the board leaking might be the issue -> when pluggin in USB the fan spins, so mayby there is leakake eather way. i will try to tape out +5V and - and leave the signale+-. is this something that can be done?
|
|
|
|
Gator-hex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 02:47:26 PM |
|
i keep getting failures on the hex 16A2 the failure keeps happening periodically and hexboard disables and then starts a new one -> might be over 30-50per day. most of the time its ZOMBIE or from faulty to DEAD.
re-starting everything sometimes help, but now i'm starting to get the following (tried 3.xx and 4.0.0 and 4.2.2 versions)
HEXC failure -> disabling **** glibc detected - cgminer malloc(): memory corruption : 0x012dd718
what wrong?
Visual check your HEX16C, see if there is any burn component. You can get random restarts from using USB1 (too slow) or multiple power supplies on a shared USB hub (try a power protected hub or seperate everything) or one of the boards is leaking power on the USB (try taping out the gnd/+5V in the USB cable). about burned component : No Visual problem seen, also works sometimes a while -> so mayby components ok! about the USB -> i have USB2 cables but the board leaking might be the issue -> when pluggin in USB the fan spins, so mayby there is leakake eather way. i will try to tape out +5V and - and leave the signale+-. is this something that can be done? Yes, I discussed this solution originally in the Hex16b Hands on thread https://bitcointalk.org/index.php?topic=338790.msg4642613#msg4642613Just cut some thin strips of cellotape and tape over the outer pins. You'll know which ones are leaking if you connect them to a power protected USB hub they won't communicate or light up, but yeah the fans running when they're connected to USB power only is a good sign too. Oh and also some power supplies can reset if there is nothing on the 5v line. I put a fan on it, but some people use an old HDD/CD/DVD.
|
|
|
|
QuiveringGibbage
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 07, 2014, 04:32:03 PM |
|
hey marto74, what's the chances of getting something (say.. extra h/w) for the DOA and $500AUD to DHL the damn things back to TechnoBit? ![Tongue](https://bitcointalk.org/Smileys/default/tongue.gif) did I mention the lost shares from half a THs of hashing power while I go through this RMA process? Hi marto74, Thanks for the prompt RMA process. I've received the 2 units back and appreciate your responses to my queries. Nice work on cgminer-4.2.2. Keep up the good work. 0: HEX8 0 : 270 1000/1005mV | 514.8G / 262.8Gh/s 1: HEX8 1 : 270 1000/ 999mV | 17.38G / 249.6Gh/s 2: HEX8 2 : 270 1000/1008mV | 368.9G / 259.6Gh/s 3: HEX8 3 : 270 1000/ 999mV | 267.0G / 266.0Gh/s
Pics can be found http://imgur.com/a/mRbMZ#hGO5lYOCheers, QG
|
Bitcoin is at the tippity top of the mountain...but it's really only half way up.. ![Wink](https://bitcointalk.org/Smileys/default/wink.gif)
|
|
|
poldo82l
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 09, 2014, 06:15:52 PM |
|
Hi technobit is marto74 a month I came hex8a1 and is a month that I'm struggling to get it working by asking multiple times for help to Martin Sirakov results the miner has problems fixed light remains lit red and more than 20 GH -60/s can not undermine when it works.I then asked to replace the plunger around two weeks ago, you answered me shipped new hex8a1 I asked the shipping tracking no object has arrived and even the traking shipping!!!!!!I lost a month managed to undermine having paid the 1350 € per order hardware in January now the same hardware is 800 € and I find myself with the HEX8A1 not working!!!!!!!!!!!!!!!!!!!!!
|
|
|
|
loshia
Legendary
Offline
Activity: 1610
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 09, 2014, 06:37:43 PM |
|
Hi technobit is marto74 a month I came hex8a1 and is a month that I'm struggling to get it working by asking multiple times for help to Martin Sirakov results the miner has problems fixed light remains lit red and more than 20 GH -60/s can not undermine when it works.I then asked to replace the plunger around two weeks ago, you answered me shipped new hex8a1 I asked the shipping tracking no object has arrived and even the traking shipping!!!!!!I lost a month managed to undermine having paid the 1350 € per order hardware in January now the same hardware is 800 € and I find myself with the HEX8A1 not working!!!!!!!!!!!!!!!!!!!!!
Dude can you explain what is wrong with the board? This is your first post so if you can be more specific with details there is some chance to fix it remotely
|
|
|
|
poldo82l
Newbie
Offline
Activity: 3
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 09, 2014, 07:38:23 PM |
|
He already tried Martin Sirakov technobit's remote from in solving the problem but nothing, the miner hexminer 1.0.0.3 software does not want to know to leave remains on gh/0.000 s just putting mark on test only or later by taking part but does not go beyond the 60 gh/s when okay otherwise fixed lights up the red light and comes only with the gh 20/s
|
|
|
|
Zich
Legendary
Offline
Activity: 1190
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 10, 2014, 02:25:01 AM |
|
Your explanation is null dude. I take that english is not your main language. You can ask for help on this thread yet you didn't. You need to tell us you hardware specs, PSU capacity, HUB, & shot some picture. If you insist on windows, you will had headache since no working cgminer 1 month ago but recently 2GOOD had posting working cgminer with technobit support. Best course is to use TPLINK TL-MR3020 as host.
|
|
|
|
|