zugvogel21
|
|
May 19, 2014, 11:00:25 AM |
|
Hello,
i have a problem with my blades. The miner i am using is cgminer 3.7.2 gridseed. I have 7 blades on my laptop. Installed Windows usb drivers. When i run cgminer it only detects one gsd. not more. i have first to start cg and then plug in the blades after running it. Then it detects all blades. Also cg shuts down one time a day. This happens most times in the night. Everytime a differnt time. Can please somebody help me ?
It's better to use cpuminer-gc3355, download: https://www.dropbox.com/s/ttqa9p851siz8oi/minerd-gc3355.zipDocumentation is here: https://github.com/siklon/cpuminer-gc3355Really ? I just started it after made the config with my pools. It detects all my gsd, also gets new jobs but they get no hashrate. Also in my pool there is shown zero hashrate. Is the config made for the blades ? With bfgminer i had the same problem with shutting down. Did you have same problems ?
|
█████ █████ ███████ █████ ███ █████████████ █████ ██ █████████████████ █████ █ ██████ ██████ █████ ████ ████ █████████████ █████ ████ █████████████ █████ ████ █████████████ █████ ████ █████ █████ █████ █ ██████ ███████ █████ ██ ███████████ █████ █████ ███ █████████ ████ █████ █████ ███████ ██ | | | ███ ███ ███ ███ ███ ███ ███ ███ ███ | | | | | | ███ ███ ███ ███ ███ ███ ███ ███ ███ | | ►WhitePaper ►One-Pager | ███ ███ ███ ███ ███ ███ ███ ███ ███ | | | | ███ ███ ███ ███ ███ ███ ███ ███ ███ | | ███ ███ ███ ███ ███ ███ ███ ███ ███ | █████ █████ ███████ █████ ███ █████████████ █████ ██ █████████████████ █████ █ ██████ ██████ █████ ████ ████ █████████████ █████ ████ █████████████ █████ ████ █████████████ █████ ████ █████ █████ █████ █ ██████ ███████ █████ ██ ███████████ █████ █████ ███ █████████ ████ █████ █████ ███████ ██ |
|
|
|
|
wolf_miner
Legendary
Offline
Activity: 1018
Merit: 1001
|
|
May 19, 2014, 01:52:00 PM |
|
Hi, I have a linux thin client (Tiny core Linux) that I want to use for driving 3 Gridseed Mini, please can you suggest me which program i have to use / compile for mining?
Thanks in advance W_M
|
|
|
|
sandor111
|
|
May 19, 2014, 01:54:29 PM |
|
Hi, I have a linux thin client (Tiny core Linux) that I want to use for driving 3 Gridseed Mini, please can you suggest me which program i have to use / compile for mining?
Thanks in advance W_M
You can use cpuminer-gc3355: https://github.com/siklon/cpuminer-gc3355
|
|
|
|
wolfey2014
|
|
May 19, 2014, 02:05:18 PM |
|
Hello,
i have a problem with my blades. The miner i am using is cgminer 3.7.2 gridseed. I have 7 blades on my laptop. Installed Windows usb drivers. When i run cgminer it only detects one gsd. not more. i have first to start cg and then plug in the blades after running it. Then it detects all blades. Also cg shuts down one time a day. This happens most times in the night. Everytime a differnt time. Can please somebody help me ?
Search for these two words... FIFO BUFFERS Read, be amazed, duplicate, apply, rejoice!
|
I Modify Miners Professionally! PM me for details!
|
|
|
wolf_miner
Legendary
Offline
Activity: 1018
Merit: 1001
|
|
May 19, 2014, 02:13:45 PM |
|
Hi sandor111, i try to compile cpuminer-gc3355, but I have an error can you help me? tc@box:/home/cpuminer-gc3355$ sudo ./autogen.sh configure.ac:13: installing './compile' configure.ac:4: installing './config.guess' configure.ac:4: installing './config.sub' configure.ac:6: installing './install-sh' configure.ac:6: installing './missing' Makefile.am: installing './INSTALL' Makefile.am: installing './depcomp' configure.ac:114: error: possibly undefined macro: AC_MSG_ERROR If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. tc@box:/home/cpuminer-gc3355$
Thanks in advance W_M
|
|
|
|
sandor111
|
|
May 19, 2014, 02:25:10 PM |
|
Hi sandor111, i try to compile cpuminer-gc3355, but I have an error can you help me? tc@box:/home/cpuminer-gc3355$ sudo ./autogen.sh configure.ac:13: installing './compile' configure.ac:4: installing './config.guess' configure.ac:4: installing './config.sub' configure.ac:6: installing './install-sh' configure.ac:6: installing './missing' Makefile.am: installing './INSTALL' Makefile.am: installing './depcomp' configure.ac:114: error: possibly undefined macro: AC_MSG_ERROR If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. tc@box:/home/cpuminer-gc3355$
Thanks in advance W_M Make sure the necessary packages are installed.
|
|
|
|
pjcltd
Legendary
Offline
Activity: 1778
Merit: 1003
NodeMasters
|
|
May 19, 2014, 03:07:16 PM |
|
Hi sandor111, i try to compile cpuminer-gc3355, but I have an error can you help me? tc@box:/home/cpuminer-gc3355$ sudo ./autogen.sh configure.ac:13: installing './compile' configure.ac:4: installing './config.guess' configure.ac:4: installing './config.sub' configure.ac:6: installing './install-sh' configure.ac:6: installing './missing' Makefile.am: installing './INSTALL' Makefile.am: installing './depcomp' configure.ac:114: error: possibly undefined macro: AC_MSG_ERROR If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. tc@box:/home/cpuminer-gc3355$
Thanks in advance W_M Make sure the necessary packages are installed. Hi try this make sure you are sudo su to root cd apt-get install build-essential libtool libcurl4-openssl-dev libncurses5-dev libudev-dev autoconf automake screen wget http://curl.haxx.se/download/curl-7.34.0.tar.bz2 wget http://www.digip.org/jansson/releases/jansson-2.5.tar.bz2tar -xvf curl-7.34.0.tar.bz2 cd curl-7.34.0 ./configure make make install cd .. tar -xvf jansson-2.5.tar.bz2 cd jansson-2.5 ./configure make make install wget http://ftp.osuosl.org/pub/ubuntu/pool/main/a/automake1.11/automake1.11_1.11.6-2_all.debsudo dpkg -i automake1.11_1.11.6-2_all.deb sudo ln -s /usr/local/lib/libjansson.* /usr/lib/ cd .. =============This is the one for Gridseed blades ============== git clone https://github.com/jmordica/cgminer-gc3355================================================= if you have a problem with git then use 'apt-get install git' cd cgminer-gc3355/ ./configure --enable-scrypt --enable-gridseed make Thats it your done ./cgminer --gridseed-options=baud=115200,freq=800,chips=40,modules=1,usefifo=0,btc=0 --hotplug=0 this works on Ubuntu 13.10 and the new version 14 Ubuntu Hope this helps you out.
|
|
|
|
wolf_miner
Legendary
Offline
Activity: 1018
Merit: 1001
|
|
May 19, 2014, 03:41:23 PM |
|
Hi pjcltd, thanks for your post, the problem is that on the distro I have to use some packages have different name or aren't available. openssh.tcz git.tcz nano.tcz libtool-dev.tcz curl-dev.tcz ncurses-dev.tcz libusb-dev.tcz udev-extra.tcz autoconf.tcz automake.tcz m4.tcz compiletc.tcz ntpclient.tcz screen.tcz with this packages usually I am able to compile CGMINER W_M
|
|
|
|
CartmanSPC
Legendary
Offline
Activity: 1270
Merit: 1000
|
|
May 19, 2014, 06:39:00 PM |
|
This is what I use on Ubuntu server: cd ~ sudo apt-get install build-essential autoconf automake libtool libcurl4-openssl-dev libncurses5-dev libudev-dev libjansson-dev sudo git clone git://github.com/siklon/cpuminer-gc3355.git cd cpuminer-gc3355 sudo ./autogen.sh sudo ./configure CFLAGS="-O2" sudo make
|
|
|
|
favelle75
|
|
May 20, 2014, 05:38:17 PM |
|
Power supply question. When I tap into a 12v (yellow), in a typical power supply, does it matter if I spread it around to say PCI, SATA, CPU, etc etc cables? If I wanted to run 2 Gridseed Blades off of a 500W power supply, can I just tap into the molex cables and be done with it, or do I specifically have to use the PCI-e cables?
Assuming all wires are 18 AWG - which they typically are - you should not hang more than 6A on one yellow wire. Which is roughly one half of one blade. PCI-E cables have three 12V wires each, and your 500W supply probably has two of these, so run one blade on each PCI-E cable and you'll be fine. Thanks suchmoon, that helps. One more question, if a PS has multiple rails, and most over 500W do, how do you know which 12V yellows are on which rail so you don't overload it? I wouldn't say most have multiple rails, but the ones that I've seen had it laid out on the label or in the manual. Normally on a multirail PSU you would have each pair of PCI-E connectors on a separate rail, so if you put 1-1.5 blades on each connector you would distribute the load just fine. You could probably figure it out with a multimeter too, I just never needed to. Hey suchmoon, one more question: does it matter in the PCI-e cable what order the black (neutral) and yellows (12V) are paired up?
|
|
|
|
suchmoon
Legendary
Offline
Activity: 3808
Merit: 9023
https://bpip.org
|
|
May 20, 2014, 08:08:11 PM |
|
Hey suchmoon, one more question: does it matter in the PCI-e cable what order the black (neutral) and yellows (12V) are paired up?
No, it doesn't.
|
|
|
|
favelle75
|
|
May 20, 2014, 09:03:29 PM |
|
Hey suchmoon, one more question: does it matter in the PCI-e cable what order the black (neutral) and yellows (12V) are paired up?
No, it doesn't. Sweet, thanks.
|
|
|
|
Monzsta
Member
Offline
Activity: 75
Merit: 10
|
|
May 24, 2014, 11:57:01 PM |
|
I can get cpuminer working and mining scrypt by leaving the st32 driver intact and using the assigned port in the startup bat. I can get cgminer running and mining SHA by using zadig and replacing the driver with a win32 driver. but I can't get them working at the same time, as you would dual mining. Cpuminer can't find the gridseed if the win32 driver is installed. Cgminer can't communicate with the gridseed if the ST32 driver is installed. Being as I want to dual mine, what do I do? I've got them both working, just not together.
|
|
|
|
thevictimofuktyranny
Legendary
Offline
Activity: 1092
Merit: 1004
|
|
May 26, 2014, 09:00:42 PM |
|
Hi
Does anyone know how any software that will automatically reset my USB ports every 4 hours. On Windows 7 whilst dual mining my Gridseeds need resetting every 4 hours.
Help would be very much appreciated
|
|
|
|
CartmanSPC
Legendary
Offline
Activity: 1270
Merit: 1000
|
|
May 27, 2014, 01:10:05 AM |
|
Hi
Does anyone know how any software that will automatically reset my USB ports every 4 hours. On Windows 7 whilst dual mining my Gridseeds need resetting every 4 hours.
Help would be very much appreciated
My solution was switching to Linux
|
|
|
|
thevictimofuktyranny
Legendary
Offline
Activity: 1092
Merit: 1004
|
|
May 27, 2014, 12:21:44 PM |
|
Hi
Does anyone know how any software that will automatically reset my USB ports every 4 hours. On Windows 7 whilst dual mining my Gridseeds need resetting every 4 hours.
Help would be very much appreciated
My solution was switching to Linux Which version of linux did you use? There are so many to choose from?
|
|
|
|
pjcltd
Legendary
Offline
Activity: 1778
Merit: 1003
NodeMasters
|
|
May 27, 2014, 02:15:30 PM |
|
Hi
Does anyone know how any software that will automatically reset my USB ports every 4 hours. On Windows 7 whilst dual mining my Gridseeds need resetting every 4 hours.
Help would be very much appreciated
My solution was switching to Linux Which version of linux did you use? There are so many to choose from? Hi Yes there are loads to choose from but why not use one that is working with the right information on this thread. I used this http://www.ubuntu.comdownload and install it on your PC then follow this make sure you are sudo su to root cd apt-get install build-essential libtool libcurl4-openssl-dev libncurses5-dev libudev-dev autoconf automake screen wget http://curl.haxx.se/download/curl-7.34.0.tar.bz2 wget http://www.digip.org/jansson/releases/jansson-2.5.tar.bz2tar -xvf curl-7.34.0.tar.bz2 cd curl-7.34.0 ./configure make make install cd .. tar -xvf jansson-2.5.tar.bz2 cd jansson-2.5 ./configure make make install wget http://ftp.osuosl.org/pub/ubuntu/pool/main/a/automake1.11/automake1.11_1.11.6-2_all.debsudo dpkg -i automake1.11_1.11.6-2_all.deb sudo ln -s /usr/local/lib/libjansson.* /usr/lib/ cd .. =============This is the one for Gridseed blades ============== git clone https://github.com/jmordica/cgminer-gc3355================================================= if you have a problem with git then use 'apt-get install git' cd cgminer-gc3355/ ./configure --enable-scrypt --enable-gridseed make Thats it your done ./cgminer --gridseed-options=baud=115200,freq=800,chips=40,modules=1,usefifo=0,btc=0 --hotplug=0 this works on Ubuntu 13.10 and the new version 14 Ubuntu Hope this helps you out.
|
|
|
|
thevictimofuktyranny
Legendary
Offline
Activity: 1092
Merit: 1004
|
|
May 27, 2014, 09:30:41 PM |
|
Hi
Does anyone know how any software that will automatically reset my USB ports every 4 hours. On Windows 7 whilst dual mining my Gridseeds need resetting every 4 hours.
Help would be very much appreciated
My solution was switching to Linux Which version of linux did you use? There are so many to choose from? Hi Yes there are loads to choose from but why not use one that is working with the right information on this thread. I used this http://www.ubuntu.comdownload and install it on your PC then follow this make sure you are sudo su to root cd apt-get install build-essential libtool libcurl4-openssl-dev libncurses5-dev libudev-dev autoconf automake screen wget http://curl.haxx.se/download/curl-7.34.0.tar.bz2 wget http://www.digip.org/jansson/releases/jansson-2.5.tar.bz2tar -xvf curl-7.34.0.tar.bz2 cd curl-7.34.0 ./configure make make install cd .. tar -xvf jansson-2.5.tar.bz2 cd jansson-2.5 ./configure make make install wget http://ftp.osuosl.org/pub/ubuntu/pool/main/a/automake1.11/automake1.11_1.11.6-2_all.debsudo dpkg -i automake1.11_1.11.6-2_all.deb sudo ln -s /usr/local/lib/libjansson.* /usr/lib/ cd .. =============This is the one for Gridseed blades ============== git clone https://github.com/jmordica/cgminer-gc3355================================================= if you have a problem with git then use 'apt-get install git' cd cgminer-gc3355/ ./configure --enable-scrypt --enable-gridseed make Thats it your done ./cgminer --gridseed-options=baud=115200,freq=800,chips=40,modules=1,usefifo=0,btc=0 --hotplug=0 this works on Ubuntu 13.10 and the new version 14 Ubuntu Hope this helps you out. Hi, I forgot to mention in my original question that I needed dual mining mode, because I'm mining BTC and Scrypt. The problem only occurs in dual mode. Scrypt only mode works perfectly with cpuminer made by Sandor111. I think you instructions are for scrypt! My mistake, please accept my apology for that!
|
|
|
|
BiggerDook
Newbie
Offline
Activity: 6
Merit: 0
|
|
May 29, 2014, 11:19:52 AM |
|
Hi
So i have 2 Gridseeds, and am using CGMiner for them to hash in SHA256 (at around 12.5GHS total) and CPUMiner for Scrypt (at around 600mhs total) - Connected to a Windows 7 PC.
I've read they should be able to hash upto 11GHS each in SHA256 only mode, but i can't figure out how to get them upto those speeds in SHA256 only?
Any advise?
Thanks
|
|
|
|
fam0us
Newbie
Offline
Activity: 10
Merit: 0
|
|
May 30, 2014, 05:56:10 PM |
|
HELP!
I had 10 of my 25 blades crash yesterday unexpectantly, and now they'll power on(the fan spins), but no lights come on at all. I've tried other gridseeds on the same USB/Pi , and they work without issue. I've tried cycling the power on both the 5V and 12V connections, but nothing seems to be working. Any suggestions? Whats the process for RMA?
|
|
|
|
|