RichBC
|
|
April 22, 2016, 05:17:02 AM |
|
hitting save and apply just does these commands. write to config file /etc/init.d/cgminer stop wait a few seconds /etc/init.d/cgminer start you can make an emergency reboot script if it doesnt hash in x amount of time.. like this E=`cgminer-api summary | grep "^ *\[Elapsed\]" | cut -d'>' -f2 | tr -d ' '` # 600=10 minutes S=`cgminer-api | grep 'GHS 5s] => ' | cut -c 16- | tr -d '.'` minhash=300 # 3GHS
if [ "$E" == "" ] || [ "$E" -gt "600" ] || [ "$S" == "" ] || [ "$S" == "0" ] ; then if [ "$S" == "" ] || [ "$S" -lt $minhash ]; then /sbin/reboot fi fi
this will after 10 mintutes check to see if the r1 is hashing below a certain amount and if it is reboot. Many thanks aaron6 just what I needed. Where is the Save & Apply Script found? Rich
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
April 22, 2016, 06:17:30 AM |
|
hitting save and apply just does these commands. write to config file /etc/init.d/cgminer stop wait a few seconds /etc/init.d/cgminer start you can make an emergency reboot script if it doesnt hash in x amount of time.. like this E=`cgminer-api summary | grep "^ *\[Elapsed\]" | cut -d'>' -f2 | tr -d ' '` # 600=10 minutes S=`cgminer-api | grep 'GHS 5s] => ' | cut -c 16- | tr -d '.'` minhash=300 # 3GHS
if [ "$E" == "" ] || [ "$E" -gt "600" ] || [ "$S" == "" ] || [ "$S" == "0" ] ; then if [ "$S" == "" ] || [ "$S" -lt $minhash ]; then /sbin/reboot fi fi
this will after 10 mintutes check to see if the r1 is hashing below a certain amount and if it is reboot. Many thanks aaron6 just what I needed. Where is the Save & Apply Script found? Rich its not a script, its just in the lua. /usr/lib/lua/luci/model/cbi/cgminer
|
|
|
|
RichBC
|
|
April 22, 2016, 06:59:04 AM Last edit: April 22, 2016, 07:29:12 AM by RichBC |
|
Hi Rich, maybe you can help me with that issue : I´m wondering, where do you connect the Pot for adjusting the core voltage? In my point of view (after studying the TI TPS53355 datasheet), I tried to use the -> "VFB" connector (Pin 1) to adjust the VCore, (between GND and Vout with a pre-resistor (like in the schematic link) but there is no change, Vcore doesn´t inc or dec, it´s constant on 0.608V . I´m working with a new release (V 1.09) of the R1 (there is something different (PCB layout, schmeatics) compared with the older ones. It´s an error in reasoning ? Maybe you can help Thx in advance , andY Hi Andy am away from home so cannot look at the board to see exactly what I did, however just checking the picture of the board this is what I remember. As you can see my board is V1.6 not sure if it's different from V1.09 which actually sounds older which is odd? You are on the right track but the reason why it did not work is because they have fitted a zero ohm resistor (R31) feeding back the Core Voltage to Pin 1 and they have not fitted the resistor to ground (R40) Because the feedback resistor is zero ohms a resistor to ground will have no effect. The reason they have done this is to get the absolute minimum Core voltage which I have measured at 0.61V. I cannot remember exactly how I fitted the pot, however the zero ohm resistor will have to be removed. It looks like I have 3 wires going to the pot & a series resistor, so I suspect that one end of the pot is connected to ground via the series resistor, the wiper to pin 1 & the other end of the pot to Vout. At a guess the pot is 50K & the series resistor 15K but will confirm connections & valueson Sunday when I am back home. Rich
|
|
|
|
ammi84 (OP)
|
|
April 22, 2016, 08:01:07 AM |
|
@ammi84, is it possible, to add a new worker to antrun.de for me ? andymanone 3 1B654QJKEWVZZoWGTpqP5xW3M67f6zxkKd_AMR3 BTW: it´s an great idea with gekkorun.de! If I could support it in any way, I´m in ! (but unfortunately I´m not a coder ) But all other (i.e. grab the Domain or provide some webspace or anything else ) is possible ) Thx in advance, andY done well we could use the whole script of antrun.de there are just some adjustments in the database parameters but the rest will be the same. i have to look if i can buy another special offer at my hoster got a webspace and domain package for 0.12€/Year (1€ Setup) for antrun.de
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 08:33:30 AM |
|
@ammi84, is it possible, to add a new worker to antrun.de for me ? andymanone 3 1B654QJKEWVZZoWGTpqP5xW3M67f6zxkKd_AMR3 BTW: it´s an great idea with gekkorun.de! If I could support it in any way, I´m in ! (but unfortunately I´m not a coder ) But all other (i.e. grab the Domain or provide some webspace or anything else ) is possible ) Thx in advance, andY done well we could use the whole script of antrun.de there are just some adjustments in the database parameters but the rest will be the same. i have to look if i can buy another special offer at my hoster got a webspace and domain package for 0.12€/Year (1€ Setup) for antrun.de Ahh, great!! Thx again ! @Gekkorun: okay sounds good ! But if I can do anything, let me know andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
|
ammi84 (OP)
|
|
April 22, 2016, 09:34:39 AM |
|
done welcome
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 09:43:42 AM Last edit: April 22, 2016, 01:37:09 PM by andymanone |
|
Hi Rich, maybe you can help me with that issue : I´m wondering, where do you connect the Pot for adjusting the core voltage? In my point of view (after studying the TI TPS53355 datasheet), I tried to use the -> "VFB" connector (Pin 1) to adjust the VCore, (between GND and Vout with a pre-resistor (like in the schematic link) but there is no change, Vcore doesn´t inc or dec, it´s constant on 0.608V . I´m working with a new release (V 1.09) of the R1 (there is something different (PCB layout, schmeatics) compared with the older ones. It´s an error in reasoning ? Maybe you can help Thx in advance , andY Hi Andy am away from home so cannot look at the board to see exactly what I did, however just checking the picture of the board this is what I remember. As you can see my board is V1.6 not sure if it's different from V1.09 which actually sounds older which is odd? You are on the right track but the reason why it did not work is because they have fitted a zero ohm resistor (R31) feeding back the Core Voltage to Pin 1 and they have not fitted the resistor to ground (R40) Because the feedback resistor is zero ohms a resistor to ground will have no effect. The reason they have done this is to get the absolute minimum Core voltage which I have measured at 0.61V. I cannot remember exactly how I fitted the pot, however the zero ohm resistor will have to be removed. It looks like I have 3 wires going to the pot & a series resistor, so I suspect that one end of the pot is connected to ground via the series resistor, the wiper to pin 1 & the other end of the pot to Vout. At a guess the pot is 50K & the series resistor 15K but will confirm connections & valueson Sunday when I am back home. Rich Hi Rich! Thanks a lot for your answer! That matches with my measurements! Sorry for the Typo, my PCB is not 1.09!, it´s Revision 1.9) from 01/09/2016 The problem is, that Bitmain (I guess, to prevent later modification by users!) puts a big hotglue ball on this resistor (unfortunately its not so comfortable, like on your revision ) So its hard for me to remove it without damage the PCB Here you can see, how it looks like: Resistor Glue protectBtw: for BM1384 cooling I´ve used this heatsink on both sides. It´s a little bit larger than the RPi heatsinks and works fine But finally, good to know, that I´m on the right track, with the Vcore mod . So i´ll try at weekend to remove the zero ohm resistor in any way... Thx a lot for your help! BR, andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
minibit
|
|
April 22, 2016, 10:02:50 AM |
|
That is not fair, joining and immediately capturing the first place
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 10:21:15 AM |
|
That is not fair, joining and immediately capturing the first place Yes, but calm down, you know: The higher they rise, the harder they fall andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
RichBC
|
|
April 22, 2016, 11:30:34 AM |
|
Hi Rich! Thanks a lot for your answer! That matches with my measurements! Sorry for the Typo, my PCB is not 1.09!, it´s Revision 1.9) from 01/09/2016 The problem is, that Bitmain (I guess, to prevent later modification by users!) puts a big hotglue ball on this resistor (unfortunately its not so comfortable, like on your revision ) So its hard for me to remove it without damage the PCB Here you can see, how it looks : Resistor Glue protectBtw: for BM1384 cooling I´ve used this heatsink on both sides. It´s a little bit larger than the RPi heatsinks and works fine But finally, good to know, that I´m on the right track, with the Vcore mod . So i´ll try at weekend to remove the zero ohm resistor in any way... Thx a lot for your help! BR, andY I wonder why they have put on some Glue as I can't see many people taking these apart, and anyone that does is not going to be put off by a bit of glue? I would just try and prise it off, perhaps try warming it if it doesn't come off easily. V1.9 looks like quite a big Rev, do you have a picture of the whole board to compare? I like the heatsink, where did that come from? Rich
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 12:19:00 PM |
|
Hi Rich! Thanks a lot for your answer! That matches with my measurements! Sorry for the Typo, my PCB is not 1.09!, it´s Revision 1.9) from 01/09/2016 The problem is, that Bitmain (I guess, to prevent later modification by users!) puts a big hotglue ball on this resistor (unfortunately its not so comfortable, like on your revision ) So its hard for me to remove it without damage the PCB Here you can see, how it looks : Resistor Glue protectBtw: for BM1384 cooling I´ve used this heatsink on both sides. It´s a little bit larger than the RPi heatsinks and works fine But finally, good to know, that I´m on the right track, with the Vcore mod . So i´ll try at weekend to remove the zero ohm resistor in any way... Thx a lot for your help! BR, andY I wonder why they have put on some Glue as I can't see many people taking these apart, and anyone that does is not going to be put off by a bit of glue? I would just try and prise it off, perhaps try warming it if it doesn't come off easily. V1.9 looks like quite a big Rev, do you have a picture of the whole board to compare? I like the heatsink, where did that come from? Rich I´m not sure, what the reason for the glue is , but believe me, it's not easy to take it off Its very flat and really strong. I tried to remove it with a small screw driver, no way... Than I tried it with some heat air (Air Rework-Station), but it´s seems to be "hard like stone", and I don´t want do damage the PCB. @V1.9 PCB Revision: yes, I took a lot of pictures when I was disassembling and modify the R1 You can get it of course ! Let me know how... (I can put it for you in a zip-file for download if you want.. or can also make an upload to my image-hoster.) @Heatsink: Yes, i bought it here: Silverbead Heatsink(It´s an german reseller, but i think it´s also available in EU) BR, andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
RichBC
|
|
April 22, 2016, 12:27:58 PM |
|
I´m not sure, what the reason for the glue is , but believe me, it's not easy to take it off Its very flat and really strong. I tried to remove it with a small screw driver, no way... Than I tried it with some heat air (Air Rework-Station), but it´s seems to be "hard like stone", and I don´t want do damage the PCB. @V1.9 PCB Revision: yes, I took a lot of pictures when I was disassembling and modify the R1 You can get it of course ! Let me know how... (I can put it for you in a zip-file for download if you want.. or can also make an upload to my image-hoster.) @Heatsink: Yes, i bought it here: Silverbead Heatsink(It´s an german reseller, but i think it´s also available in EU) BR, andY Interesting, seems a lot of trouble to go to just to cover up a zero ohm resistor? Can you see what is underneath the glue, does it look like a resistor? Must be something we are missing here? Another possibility is to trace the tracks and find a point to cut a track and just leave it all in place? After cutting you could make a measurement to confirm it is still a zero ohn resistor? Yes if you could put it in your image-hoster and PM me a link that would be great. Rich
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 12:57:05 PM |
|
I´m not sure, what the reason for the glue is , but believe me, it's not easy to take it off Its very flat and really strong. I tried to remove it with a small screw driver, no way... Than I tried it with some heat air (Air Rework-Station), but it´s seems to be "hard like stone", and I don´t want do damage the PCB. @V1.9 PCB Revision: yes, I took a lot of pictures when I was disassembling and modify the R1 You can get it of course ! Let me know how... (I can put it for you in a zip-file for download if you want.. or can also make an upload to my image-hoster.) @Heatsink: Yes, i bought it here: Silverbead Heatsink(It´s an german reseller, but i think it´s also available in EU) BR, andY Interesting, seems a lot of trouble to go to just to cover up a zero ohm resistor? Can you see what is underneath the glue, does it look like a resistor? Must be something we are missing here? Another possibility is to trace the tracks and find a point to cut a track and just leave it all in place? After cutting you could make a measurement to confirm it is still a zero ohn resistor? Yes if you could put it in your image-hoster and PM me a link that would be great. Rich @Glue: yes it´s a resitor and a capacitor covered by the glue and its connected to 53355´s PIN 1 (you can see on my picture there is the print on the left site of glue, R31 (Resistor) and C29 (Capacitor) Very strange is, that R40 (you can see it on top of R31) is missing on my PBC, but on yours it was connected before? Another possibility is to trace the tracks and find a point to cut a track and just leave it all in place? Yes, thats will be the next step, I think! @pics: okay, no problem ! I´ll do it this eve or tomorrow, when I´m back at home. andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
RichBC
|
|
April 22, 2016, 02:16:44 PM |
|
@Glue: yes it´s a resitor and a capacitor covered by the glue and its connected to 53355´s PIN 1 (you can see on my picture there is the print on the left site of glue, R31 (Resistor) and C29 (Capacitor) Very strange is, that R40 (you can see it on top of R31) is missing on my PBC, but on yours it was connected before? Another possibility is to trace the tracks and find a point to cut a track and just leave it all in place? Yes, thats will be the next step, I think! @pics: okay, no problem ! I´ll do it this eve or tomorrow, when I´m back at home. andY R40 is a position for the resistor to ground on FB and is not fitted on either rev. I did not remove it only R31 the zero ohm resistor. This has been done so the the Vcore voltage is fed straight back to Pin 1 with no potential divider, this gives them the absolute minimum Vcore possible. Rich
|
|
|
|
minibit
|
|
April 22, 2016, 02:31:27 PM |
|
Hi all, ckpool has some problems. Some miners went offline or switched to failover pool. Please don't forget to set it all back to ck, once the site's problems are gone...
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 02:36:17 PM |
|
@Glue: yes it´s a resitor and a capacitor covered by the glue and its connected to 53355´s PIN 1 (you can see on my picture there is the print on the left site of glue, R31 (Resistor) and C29 (Capacitor) Very strange is, that R40 (you can see it on top of R31) is missing on my PBC, but on yours it was connected before? Another possibility is to trace the tracks and find a point to cut a track and just leave it all in place? Yes, thats will be the next step, I think! @pics: okay, no problem ! I´ll do it this eve or tomorrow, when I´m back at home. andY R40 is a position for the resistor to ground on FB and is not fitted on either rev. I did not remove it only R31 the zero ohm resistor. This has been done so the the Vcore voltage is fed straight back to Pin 1 with no potential divider, this gives them the absolute minimum Vcore possible. Rich @R40: Ahh, okay!!! Yes, thats the same Resistor (R31!), covered by glue on my revision... Btw: I´ll send you a PM with a link to a couple of R1 pictures, I made . andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 02:43:00 PM |
|
Hi all, ckpool has some problems. Some miners went offline or switched to failover pool. Please don't forget to set it all back to ck, once the site's problems are gone... Ohh, yes, i recognized, that all my workers switched from de.ckpool.org to solo.ckpool.org . But the solo.ckpool.org seems to work . BR, andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
|
April 22, 2016, 03:22:24 PM |
|
Hi all, ckpool has some problems. Some miners went offline or switched to failover pool. Please don't forget to set it all back to ck, once the site's problems are gone... Ohh, yes, i recognized, that all my workers switched from de.ckpool.org to solo.ckpool.org . But the solo.ckpool.org seems to work . BR, andY ck has posted in the ckpool thread that DE provider is under DDOS attack. https://bitcointalk.org/index.php?topic=763510.msg14630307#msg14630307
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 22, 2016, 03:25:35 PM |
|
Hi all, ckpool has some problems. Some miners went offline or switched to failover pool. Please don't forget to set it all back to ck, once the site's problems are gone... Ohh, yes, i recognized, that all my workers switched from de.ckpool.org to solo.ckpool.org . But the solo.ckpool.org seems to work . BR, andY ck has posted in the ckpool thread that DE provider is under DDOS attack. https://bitcointalk.org/index.php?topic=763510.msg14630307#msg14630307Ah, thanks for the update, Citronick! andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
|