[Mining OS] SimpleMining.net - Manage Your GPU farm the easy way! (30 days free)

[gaato77]

hi.
Have a problem with 2 of my rigs.

COMPONENTS OF THIS 2 RIGS.

ASUS STRIX B250F MOBO
6x XFX RX580 8GB
INTEL CELERON 3900
4GB MEMO.
6 RISERS VS 006.
SMOS (RX version) installed on USB (works! i tested in other 3 rigs and the usb drive its OK)

When boot in this two rigs got this..

Pcie bus error: severity=corrected, type=Physical Layer, Id=00eb (Receiver ID) device [8086:a29b] error status/mask=00000001/00002000

 
2 videos of the problem


LINK! ->    https://drive.google.com/open?id=1GUpVsD2R7s3iZmWLJZ7I09TxAZlAZ_vm


Happens with only one card, 2 cards, 3cards,.... 6 cards conected.

And in two different rigs, so... the risers are OK.

BIOS set up:

Disabled Sound
Power ON after power loss selected
On board graphics - Enabled selected IGFX
PCI speed Gen 2
Above 4G Enabled
ASPM is Disabled








Thanks for your answers.

Hope you can help me.

Best regards

[1714739188]

1714739188

[1714739188]

1714739188

[1714739188]

1714739188

[azertypaco]

Now that my rig stability problems are fixed... I have another type of problem with my network.

Basically, it appears as though my mining rig sometimes kills my router completely.

First time last week and back then I really thought the router was the problem:
My internet was down on my wifi.
So I went to check on my PC. No internet either.
I try to connect to my router (tp-link N750) and it can't be reached.
I rebooted the router. No change.
I reset the router. No change.
I connect a laptop straight to the modem: internet is up.

So I figured that the router was faulty and I went to the store to buy a new one: tp-link Archer C7.

Now I don't remember if I had turned off my rig before installing the new one... The new one worked... for a week.

Last night I got the same problems: no internet and can't even connect to the router.
But instead of trying to reboot and reset the router, I just turned off my mining rig. And voilà, everything was working again, I did not even need to restart the router.
Today I got the same problem again.  I turned off my rig and 1 minute later my network was up again.

The rig was stuck at the "Connecting to simplemining..." stage when I turned it off.

On my router admin pages I can't see any errors in the logs.

Important note: I have a switch between the router and the mining rig.  It's a basic dlink DGS-1005G.
I will try removing that switch from the setup and plug my rig directly in the routeur to see if it helps.

Any clues other then that? 

Some discussions about similar issues I found:
https://www.reddit.com/r/EtherMining/comments/6xkau1/simplemining_os_with_5_or_6_gtx_1070s_makes/
https://www.reddit.com/r/ethOSdistro/comments/7k49ti/ethos_and_my_network_issues/

So I have 5 rigs running with 45 1070ti total and I get exact same. It seems One will get knocked offline and then soon all of them are offline trying to connect to server even though I have perfect internet available as I monitor it on my iPad. I turn off the one that had a card stopped on past and all of the other 4 rigs instantly reconnect and go on with no downtime. I tried setting each rig up under a different miner name but no difference when it happens. Also, it has run 4 days stable no problems, suddenly like 5 crashes earlier and then stable again, I just start turning off miners till I find culprit and the rest reconnect and restart the ones I turned off. I tried using the new file of Smos for NVidia cards on a new usb, but so far seems to be real buggy, I have to unplug and Re plug my usb on startup because it says usb bad. About to reflash a drive with older file to see if it fixes that.

 Vosk Coin did a livestream yesterday with a miningcave rig that came with smos already loaded and had issue with new file also so had to flash another drive with older smos file too.

One strange thing, when I lost connection earlier, I went to google overclocking setting and google made me check one of the your not a robot boxes before I could continue because it said I had unusual traffic from my connection. Earlier today I also had to change the port on my Xbox when I tested multiplayer connections after I couldn’t stay connected for a game on battlefield 1.



Sorry for rant but maybe that adds more clues, maybe traffic issue, maybe a port issue?

I am surprized that 1 of your rig will cause issues to your other rigs but not to the rest of your network.
Do the rigs have anything in common that the rest of your network does not have?

Perhaps a switch that is used only for your rigs?

On my side I removed the unmanaged switch I had in the setup, now my rig and router are connected directly, but the problem still happens.

[RebelYell]

=== WARNING TO USERS ===

Hijacking of SMOS rigs is happening again.

Here's what happened to me yesterday at night: SMOS suddenly started to mine XMR. The web monitoring page showed an error, but the rig was forking full speed. I could see it was mining XMR by opening console window or by checking the monitor which is attached to the rig.

There was no change under Rig Groups configuration: the rig mined monero although my SMOS config for mining ethereum was active. Therefore I suspect the attacker didn't use frontend (like by compromising my credentials) to gain access.

The same problem occured to me last week or so when we all got the notification from the dev that we should asap add

Code:

-mport 127.0.0.1:3333

to the miner config. I did that and thought I was being safe, but apparently I am not.

I checked my router and am not forwarding any ports to outside world.

Any idea what else I could do to protect the rig from being hijacked?

Thank you and all the best to all of you honest miners!

[cryptopepe]

Hi all,

I have RX 580 GPU in rig, but in SMOS I cannot undervolt them. All value set at Core Undervolting is ignored.

Is there some other way to undervolt core and memory at SMOS?

Thank you a lot.

[adore]

@DEV, can i run the SMOS on a normal Hardisk?

sure! basically you can use any kind of storage device

[utel0978]

Fix the design for a safari
http://joxi.ru/GrqX6VGhQvWPwA

[tytanick]

UPDATE v1145
-network performance tuning - rig at startup and reload will send status every 8 seconds for first 5 minutes, so console will be more interactive and after that it will send status every 1 minute
-now the dashboard will work much faster

[twistedmonkey]

UPDATE v1145
-network performance tuning - rig at startup and reload will send status every 8 seconds for first 5 minutes, so console will be more interactive and after that it will send status every 1 minute
-now the dashboard will work much faster

seriously ? it is down... cloudflare error...

[Hexomuk]

UPDATE v1145
-network performance tuning - rig at startup and reload will send status every 8 seconds for first 5 minutes, so console will be more interactive and after that it will send status every 1 minute
-now the dashboard will work much faster

Hello and thank you for the update, any news about a new version of ccminer?

[Dragstar]

UPDATE v1145
-network performance tuning - rig at startup and reload will send status every 8 seconds for first 5 minutes, so console will be more interactive and after that it will send status every 1 minute
-now the dashboard will work much faster

Ty the web site is very fast now and also I wonder when will you add eth miner 0.13?

[tytanick]

seriously ? it is down... cloudflare error...

I dont see any problem, can you check again ?

[MRTN87]

https://image.prntscr.com/image/L5TFYzzoR2qiqPWhgVLKDQ.png

I am facing this problem. My rigs are offline on the dashboard but they are mining, i can see it on the pool,

[Onbusy]

Does SimpleMining have a way to check wattage of the GPUs?  Something simple and basic, mainly used for comparison of changing core voltage and frequencies.  Something like what GPU-Z or AfterBurner would show on a Windows machine.

[IndigoDEZ]

@Octodrachm

It looks like the GTX 1060 has two device ids.  1c03 is the first generation 1c06 is the second.  You need to install the latest NVIDIA driver for the 1c06 version to be recognized correctly.

"NVIDIA-Linux-x86_64-390.25.run" is what I use, but I am on Ubuntu.  I have found that you need to make sure that the version of gcc used to compile your kernel is the same exact version that you use to compile the NVIDIA driver kernel.

[Rambo777]

Anyone else having issues with simplemining.net?  I have rigs running but the web GUI is not showing them this started happening this morning (9am EST - GMT -5:00)

I'm Having the same Issu

[Fister]

Hi all! I just got my first two rigs up and running with smos and it works great!
I only have a question about overclocking. I am running nvidia 1060 6gb cards. When I oc I get best hashpower at +1400. And that seems to go for all my cards.
I see most other only go for +900 or something and that is max.
Am i doing something wrong or can my cards take damege somehow?

[Turocik]

I returned to mining after several years. Just one rig up and running for now. More than 10 days on SimpleMining without any issue. Rock and steady ....

[ne0x86]

now dashboard runs like a rocket

[adore]

now dashboard runs like a rocket

yes! thank you tytanick!
how did you do it? unbelievable how slow it was before compared to now.

[gaato77]

hi.
Have a problem with 2 of my rigs.

COMPONENTS OF THIS 2 RIGS.

ASUS STRIX B250F MOBO
6x XFX RX580 8GB
INTEL CELERON 3900
4GB MEMO.
6 RISERS VS 006.
SMOS (RX version) installed on USB (works! i tested in other 3 rigs and the usb drive its OK)

When boot in this two rigs got this..

Pcie bus error: severity=corrected, type=Physical Layer, Id=00eb (Receiver ID) device [8086:a29b] error status/mask=00000001/00002000

 
2 videos of the problem


LINK! ->    https://drive.google.com/open?id=1GUpVsD2R7s3iZmWLJZ7I09TxAZlAZ_vm


Happens with only one card, 2 cards, 3cards,.... 6 cards conected.

And in two different rigs, so... the risers are OK.

BIOS set up:

Disabled Sound
Power ON after power loss selected
On board graphics - Enabled selected IGFX
PCI speed Gen 2
Above 4G Enabled
ASPM is Disabled








Thanks for your answers.

Hope you can help me.

Best regards

any help? please