toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
January 18, 2017, 04:36:21 PM |
|
Well guys using Version 1.1 on suprnova on my 5 bios modded powercolor RX 470's clocked at 1250Mhz core and 1720 ram if I set a static difficulty of 1500 my reported average hashrate on the pool side is 1152h/s over 1 hr so that would break down to a effective hash of 230.4h/s per card.
SO i need to remolded my 470 to get 230 like CM with the fee off at stock setting ? . no complaints if i have to i have to ... ID rather use Gateless Gate. would you be willing to post your Exact setting ? . Above all before some one miss judges me , I m not complaining or against paying Fees that said i know it is a little bit longer and zawawa is doing his best to catch up but if some one is actually getting such high speeds please share with us your exact setting and this is not a demand ,, if you willing and don't mine other wise cool if not . My cards all have custom memory straps, I use Driver 16.6.2. Power is +5 core runs at 1250 mem runs on 1720 The actual miner reports a average of 201h/s for each card but when I set to mine at a static difficulty on suprnova of 1500 I am getting a average hashrate on the pool of over 1150h/s for my 5 card rig. I do have to say that i killed my 6th rx470 finding the ideal memory straps for my powercolor cards. First thing to try is setting your difficulty to 1500 using d=1500 as your password on suprnova pools and see what you get. I am not planning to share my straps as I would feel terrible if some one used them and fried their card. I don't blame you on the not sharing part i don't either for the same reason ,... I use Coinotron pool and two others .. so I'm ok then i get about the same at stock setting using the New AMD Drivers Crimson ReLive Edition 17.1.1 . I thought you had discovered some thing new .
|
|
|
|
OhGodAGirl
Full Member
Offline
Activity: 199
Merit: 108
Look, I'm really not that interesting. Promise.
|
|
January 18, 2017, 04:38:20 PM |
|
I may not understand much of OpenCL or graphics at all but as network engeneer I still think that hardware limits cannot be exceeded for the purpuse mentioned above. There is no queue mechanism or alike that can be used to queue solution rate AFAIK. Protocol specifics doesn't allow workarounds.
Yes we can not exceed hardware limits, but for now miner use 63% of mcu and 80% of power, so it not utilize full hardware capacity, why? I suspect that miner computation have 2 phases, one when fetching from memory - cores wait (are blocked), and second cores compute (not use memory). in simple way: now threads do: [[external memory read to registers][comp][external memory write result]][[external memory read to registers][comp][external memory write result]] so one part cores waiting, second part memory not used... i want (all at the same time): thread1: [external memory read to cache][external memory read to cache][external memory read to cache] thread2: [[read cache][comp][write cache]][[read cache][comp][write cache]][[read cache][comp][write cache]] thread3: [external memory write result][external memory write result][external memory write result] yes it have flaws in logic, but why i can not discuss that? You can discuss it - no one is saying otherwise. But resorting to name calling and abuse when someone who does this for a living tells you you're incorrect is very...well, it's a poor way to handle it. If you wish to have a discussion, you need make sure to be polite. Ask WHY your theory is not possible, instead of just resorting to name calling.
|
|
|
|
chronek
Sr. Member
Offline
Activity: 273
Merit: 250
BD People Are Legend
|
|
January 18, 2017, 04:56:56 PM |
|
But resorting to name calling and abuse when someone who does this for a living tells you you're incorrect is very...well, it's a poor way to handle it.
If someone not tell what is wrong, but just say that i am "talking out your arse." then i just praise his creative answer.
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 18, 2017, 05:35:27 PM |
|
Hmm... The existing NVIDIA busy CPU patches for SILENTARMY does not seem to work. What to do, what to do...
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 18, 2017, 06:43:20 PM |
|
OK, the new fix is somewhat working. Oh well, there is only so much I can do. I can always come back to this later.
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
th00ber
|
|
January 18, 2017, 11:34:36 PM |
|
vcruntime140.dll missing both Win7 and Win10 I tried to reinstall VC Redist / DL missing lib
But not working ... any tips on how to run this in windows ?
That's pretty weird... Are you using a 32-bit version of Windows by any chance? 64 bits both... Have you à release with the full DLL dependencies ? https://www.microsoft.com/en-us/download/confirmation.aspx?id=48145<3 I got it running on win 10. The perf are not bad at all !!
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 19, 2017, 03:15:05 AM |
|
vcruntime140.dll missing both Win7 and Win10 I tried to reinstall VC Redist / DL missing lib
But not working ... any tips on how to run this in windows ?
That's pretty weird... Are you using a 32-bit version of Windows by any chance? 64 bits both... Have you à release with the full DLL dependencies ? https://www.microsoft.com/en-us/download/confirmation.aspx?id=48145<3 I got it running on win 10. The perf are not bad at all !! Glad it's working for you. I thought I got rid of that dependency, though. Let me doublecheck.
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
john1010
|
|
January 19, 2017, 11:33:52 AM |
|
Alright, I'm finally done implementing the "variable" NR_ROWS_LOG. Now you can customize all the relevant parameters specifically for each round. I am almost hitting the 180 sol/s mark with RX 480, and GTX 1060 is reaching 170 sol/s. My wife is now constantly complaining about my forgetfulness and absent-mindedness, but that's OK...
You can rip what you sow mate All that hardwork will reward you someday.. Who know I will become a big miner soon, definitely I will use your work.. and of course you have my reward.. Just keep it up!!
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 19, 2017, 12:03:36 PM |
|
Alright, I'm finally done implementing the "variable" NR_ROWS_LOG. Now you can customize all the relevant parameters specifically for each round. I am almost hitting the 180 sol/s mark with RX 480, and GTX 1060 is reaching 170 sol/s. My wife is now constantly complaining about my forgetfulness and absent-mindedness, but that's OK...
You can rip what you sow mate All that hardwork will reward you someday.. Who know I will become a big miner soon, definitely I will use your work.. and of course you have my reward.. Just keep it up!! Hopefully... I have some pretty wild ideas, but I wonder how many of them would actually materialize. We will see.
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 19, 2017, 12:16:30 PM |
|
While preparing the GCN assembly version, I just decided on a whim to bump up the version and to add support for Ethash, CryptoNight, and NeoScrypt. I ported some of sgminer-gm's kernels to NVIDIA and also added my own optimized NeoScrypt kernel. The high CPU usage with NVIDIA cards is somewhat ameliorated, too. Enjoy! https://github.com/zawawawa/gatelessgate
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
john1010
|
|
January 19, 2017, 12:29:45 PM |
|
I tried to run it on my miner, Im running win10 x64 3x RX 480 8gb stock suddenly I got this kind of error.. My bat file: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_MAX_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
gatelessgate.exe -k equihash -o zcl-apac.suprnova.cc:4042 -u john1010.MyPC -p x -I 24 -g 2 -w 256 --thread-concurrency 8192 --lookup-gap 2 --vectors 1 --gpu-platform 0 --gpu-threads 2 --gpu-fan 75
Am I doing it right or something in my bat file is missing? @zawawa Thanks
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 19, 2017, 12:35:38 PM |
|
I tried to run it on my miner, Im running win10 x64 3x RX 480 8gb stock suddenly I got this kind of error.. My bat file: setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_MAX_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
gatelessgate.exe -k equihash -o zcl-apac.suprnova.cc:4042 -u john1010.MyPC -p x -I 24 -g 2 -w 256 --thread-concurrency 8192 --lookup-gap 2 --vectors 1 --gpu-platform 0 --gpu-threads 2 --gpu-fan 75
Am I doing it right @zawawa Thanks This problem was just addressed with Version 0.1.2. Damn the DLL Hell...
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
john1010
|
|
January 19, 2017, 12:50:35 PM |
|
@zawawa Problem solved!! I've done a good result with visual redistribute.. It's now work like a charm!! I think there's a little bit settings I need to do to get the 220h/s.. Do you have a sample bat confg for my RX 480 sir? Thanks!!
|
|
|
|
FFI2013
|
|
January 19, 2017, 04:07:30 PM |
|
Whats the difference between GPU_FORCE_64BIT_PTR=0 and GPU_FORCE_64BIT_PTR=1 Also does anyone have a good conf file for 390 and 290 they like to share Thanks
|
|
|
|
|
FFI2013
|
|
January 19, 2017, 05:42:50 PM |
|
thank you I've been looking for info on these settings good read
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 19, 2017, 07:16:15 PM |
|
@zawawa Problem solved!! I've done a good result with visual redistribute.. It's now work like a charm!! I think there's a little bit settings I need to do to get the 220h/s.. Do you have a sample bat confg for my RX 480 sir? Thanks!! I achieved that speed with a modded BIOS with altered memory strap timings. The other parameters are something like this: Core Voltage: +50mV Power Limit: +50% Core Clock: 1150MHz Memory Clock: 2150MHz I was even able to run the miner at 238 sol/s with this: Core Voltage: +50mV Power Limit: +50% Core Clock: 1250MHz Memory Clock: 2250MHz Be very careful with overclocking, though, as you could seriously damage the hardware.
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
manotroll
|
|
January 20, 2017, 01:08:22 AM |
|
I'll post the income on eth with the 390x
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
January 20, 2017, 03:35:48 AM |
|
thank you I've been looking for info on these settings good read You're welcome, took me time to find that one lost into thousands of bitcoin forum post on google when looking for the specific keywords , a very good read indeed
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
January 20, 2017, 05:27:56 PM |
|
Alright, that speech was depressing. Time to get back to programming for an alternative economy...
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
|