▂▃▅▆▇⫷[🆉🅿🅾🅾🅻.🅲🅰]⫸⫷[!Paying 10 FLUX PA's!]⫸⫷[ the miners multipool ]⫸▇▆▅▃▂

[guytechie]

Should the d=xxx set difficulty work for equihash ?

I am using the DTSM zm miner and the server is setting difficulty to  0000ffff0000000000000000 on startup.
This does not change whatever I put in the password field for d= (tried d=10  d=128 and a couple of others.)
not really a big problem but on my gtx1070 with about 450 sols/sec it mens I only submit shares about 1 per 2 minutes
the shares are being accepted fine and the average hashrate shown by zpool is close so just for interest really.
BTW, DTSM is about 10% faster on a gtx 1070 than ccminer even after taking the dev fee into account, so worth using if you are
mining equihash.


Second question :-), How come crypronight is not on the Algo list, its prob the best use of the AMD cards ?

Ta

I've asked about the equihash difficulty before.  I am having the same problem.  At 300 sols, I'm only finding shares every 3-8 minutes.  Didn't get an answer.  Good luck.

Bump.

[kakomanda]

Anyone having problems with ccminer 2.2.3?
ccminer 2.2.3 @ lyra2v2 @ 980 0 shares 20 minutes
ccminer 2.2.2 @ lyra2v2 @ 1060 lots of shares per minute

Ignore.
For some unknown reason xmr-stak was using GPU and not CPU... Go figure.

[Girrk]

https://image.prntscr.com/image/Wbqzo5p9Tp2wJ8SzcS0zfQ.png
For several hours, two miners work on 400 MH/s each = 800 MH/s.
Why is the graph and data on the pool much less?
No Reject.

[cryptominer420]

https://image.prntscr.com/image/Wbqzo5p9Tp2wJ8SzcS0zfQ.png
For several hours, two miners work on 400 MH/s each = 800 MH/s.
Why is the graph and data on the pool much less?
No Reject.

I am guessing you are new to pool mining, but anyway this is because the miner program calculates hashrate at 100% luck but in reality this can fluctuate I have had times were the pools say they are mining 200% faster than what they really are and other times were they only show 50% but over 2-3 days it averages out to be pretty close to accurate.

[kakomanda]

https://image.prntscr.com/image/Wbqzo5p9Tp2wJ8SzcS0zfQ.png
For several hours, two miners work on 400 MH/s each = 800 MH/s.
Why is the graph and data on the pool much less?
No Reject.

based on the graph, ou are lucky that you hit 800 MHs for several hours.

[BroddaThep]

https://image.prntscr.com/image/Wbqzo5p9Tp2wJ8SzcS0zfQ.png
For several hours, two miners work on 400 MH/s each = 800 MH/s.
Why is the graph and data on the pool much less?
No Reject.

I am guessing you are new to pool mining, but anyway this is because the miner program calculates hashrate at 100% luck but in reality this can fluctuate I have had times were the pools say they are mining 200% faster than what they really are and other times were they only show 50% but over 2-3 days it averages out to be pretty close to accurate.

No, that isn't what is going on. 

I had three rigs trying to mine lyra2v2 100% of the time.

A does 420 MH/s, B does 210 MH/s, C does 60 MH/s.

According to zpool A does 380ish, B does 75 MH/s and C does 40 MH/s.

I have verified that every single rig mines at the expected hash rate for ZEC and Ethereum on Nanopool.  I even went out and did a complete rework of my network.  There was no difference as far as mining goes, though I went from 70 ms ping to 20 ms ping and 2 Mbits up/down to 100 Mbits up/down.

Must be a problem with ZPool, right?  I switched rig B to miningpoolhub and it was not any better.  So it doesn't really seem to be a problem with ZPool.  Why does A almost work, while B and C are garbage?  And this was over a period of two days.   I have since moved over to mining ZEC on nanapool and they have been rock solid.  I still have rig A on zpool since it was making very good money.

Perhaps something is just odd with lyra2v2?  I have been thinking about joining a straight monacoin mining pool to see if there is a difference.

Of course, I haven't been able to connect to zpool lyra2v2 server for over 2 hours now...  Now all my 1080Tis are mining ZEC on nanopool.  Though I would love to switch them back.

[robinlongstride]

Hello, I am interested in switching to zpool from miningpoolhub because zpool supports more coins.

It says in setup to set profitability factors in .bat file. How do I figure out the profitability factor for the rig I am using? I will be using a 1070, 1080, and 2 rx 480s for now.

Or is it fine to not set any factors in -p and leave it default?

Thanks for the help!

This post:

https://bitcointalk.org/index.php?topic=1751272.msg17921405#msg17921405

and this thread should be able to get you going:

https://bitcointalk.org/index.php?topic=1777336.msg17729122

How do I figure out the profitability factor for my Baikal ASIC? (X11,X13,X14,X15,Quark,Qubit)
https://ibb.co/dBu9VF

[JaredKaragen]

Hello, I am interested in switching to zpool from miningpoolhub because zpool supports more coins.

It says in setup to set profitability factors in .bat file. How do I figure out the profitability factor for the rig I am using? I will be using a 1070, 1080, and 2 rx 480s for now.

Or is it fine to not set any factors in -p and leave it default?

Thanks for the help!

This post:

https://bitcointalk.org/index.php?topic=1751272.msg17921405#msg17921405

and this thread should be able to get you going:

https://bitcointalk.org/index.php?topic=1777336.msg17729122

How do I figure out the profitability factor for my Baikal ASIC? (X11,X13,X14,X15,Quark,Qubit)
https://ibb.co/dBu9VF

https://bitcointalk.org/index.php?topic=1260863.msg15933612#msg15933612

Its the concept of making a normalized factor (not unlike a mole in chemistry) to rate them all to each other.

If you are reading in GH/S, then it would be 1,2,3,etc
On the same scale, if your algo is rated in Mh/s, it would be 0.001,0.002,0.003,etc.

My normalization for GPU walkthrough concepts can be applied to any device or algo.

[miner14]

No, that isn't what is going on. 

I had three rigs trying to mine lyra2v2 100% of the time.

A does 420 MH/s, B does 210 MH/s, C does 60 MH/s.

According to zpool A does 380ish, B does 75 MH/s and C does 40 MH/s.

I have verified that every single rig mines at the expected hash rate for ZEC and Ethereum on Nanopool.  I even went out and did a complete rework of my network.  There was no difference as far as mining goes, though I went from 70 ms ping to 20 ms ping and 2 Mbits up/down to 100 Mbits up/down.

Must be a problem with ZPool, right?  I switched rig B to miningpoolhub and it was not any better.  So it doesn't really seem to be a problem with ZPool.  Why does A almost work, while B and C are garbage?  And this was over a period of two days.   I have since moved over to mining ZEC on nanapool and they have been rock solid.  I still have rig A on zpool since it was making very good money.

Perhaps something is just odd with lyra2v2?  I have been thinking about joining a straight monacoin mining pool to see if there is a difference.

Of course, I haven't been able to connect to zpool lyra2v2 server for over 2 hours now...  Now all my 1080Tis are mining ZEC on nanopool.  Though I would love to switch them back.

Same here, my rig hashes around 400MH/s with Lara2RE2  and yet zpool after an hour, shows 4.7MH/s.
Don't know why or what the issue is, but it makes me feel very uncomfortable with Zpool  Especially when I can switch over and mine mone/vert directly and not have any issues with lara.

[I_M]

Something is very wrong with Lyra2v2 reported hashrates.  They keep falling:

https://imgur.com/a/Ka3bb

I'm normally pushing around 320mh/s.  It is currently reporting 3, and has been steadily declining all afternoon.

[yapdakilla]

Question regarding state owned crypto currencies (eg. Dubai's EmCash), would mining pools such as Zpool would be able to mine them and earn from discovered blocks and transaction fees in the future? What do you guys think?

[malthrax]

Something is very wrong with Lyra2v2 reported hashrates.  They keep falling:

https://imgur.com/a/Ka3bb

I'm normally pushing around 320mh/s.  It is currently reporting 3, and has been steadily declining all afternoon.

I think the pool crashed...

[BlitheJr]

I' m having a big problem, and would like help.

I'm trying to mine xevan with a rx570 in zpool, but the pool provide only a few works and show a very low hash rate like 5Kh/s.

This is very strange, because i made tests with cpuminer and in this case the pool provide work at every second an the site show hash rates much higher than with my GPU.

Why this is happening?  Someone in the pool could help to fix this?   

[bobrottenchild]

Same thing for Lyra2v2 hashrates here. Kept falling, now my balance has been stagnating for the past hours. Something is wrong.

I thought it might be temporary but the past hours have been under-reporting badly, is this normal? It surely seems not. I thought it could be normal that the reported rates might be off a little but now that's a big offset we see here...

[JaredKaragen]

I' m having a big problem, and would like help.

I'm trying to mine xevan with a rx570 in zpool, but the pool provide only a few works and show a very low hash rate like 5Kh/s.

This is very strange, because i made tests with cpuminer and in this case the pool provide work at every second an the site show hash rates much higher than with my GPU.

Why this is happening?  Someone in the pool could help to fix this?   

my guess is the miner app you are using...

These are all nvidia cards:
http://zpool.ca/?address=1kLsGT9egk3utSKZH46ydTbKj5oMnmBoN

I see nothing abnormal... aside from the common frontend dropouts.

[malthrax]

Same thing for Lyra2v2 hashrates here. Kept falling, now my balance has been stagnating for the past hours. Something is wrong.

I thought it might be temporary but the past hours have been under-reporting badly, is this normal? It surely seems not. I thought it could be normal that the reported rates might be off a little but now that's a big offset we see here...

I PM'd crackfoo, so...   for now, switch to another coin and just ride it out I guess

[Bulletdodger]

Can you have payment in BCH?
I'd rent my L3+

[stunvn]

Can you have payment in BCH?
I'd rent my L3+

Agree.

I'm looking for BCH payout.

[4ward]

Can you have payment in BCH?
I'd rent my L3+

Agree.

I'm looking for BCH payout.

You can get payout in any coin that is mined on the pool, provided there are enough blocks mined in that coin

[wolverine5pl]

Can you have payment in BCH?
I'd rent my L3+

Agree.

I'm looking for BCH payout.

You can get payout in any coin that is mined on the pool, provided there are enough blocks mined in that coin

I would like BCH too.
And cryptonight algo for my gpu's too:)

is zpool more profitable than multipool or italyiimp?
i checked http://poolpicker.eu and it is but some figures there dont make sense