[NemosMiner] multi algo profit switching NVIDIA/CPU miner

[Storx]

Question:

In regards to mining to Nicehash, what are the default fee % that NemoMiner 3.1 is calculating in regards to profitability? is it offsetting the profits by 5%, 3%, 1%? or maybe is it ignoring this and just going off pure profit with no fee taken into account?

[1714880705]

1714880705

[1714880705]

1714880705

[MrPlus]

Feature Request:

Add a separate wallet address line for Nicehash ONLY, so we can use Nicehash internal wallets and check box to trigger which fee we expect to pay so it can be added into the calculations to determine if more profitable vs other pools.



Story Behind the change:
I have been using NemoMiner over AwesomeMiner for some time now and recently upgraded to the new GUI versions on my rigs, i mainly mine to Ahashpool Plus, but i mistakenly forgot to turn off nicehash which was checked from default during install and found large periods that my Ahashpool showed huge drops in profits checking on it periodically, this boggled me as the rigs were online the entire time, but lastnight i figured out what it was, the nicehash box was checked and i overlooked this and copied the setup folder to my cloud drive so it would be downloaded on all of my rigs to later run... while on my PC and looking at my Ahashpool page i noticed that all 120+ GPU's were displayed not active miners all sudden and remoted into the rigs to check on them to find that they were mining on Nicehash. I have no issues with mining to Nicehash if it truly is more profitable than any algo on Ahashpool, just didnt expect it. The issue now is when i look at nicehash to check the payout, its sending me payments via external route and charging me 3%, if i was able to populate my internal wallet than i would incur 0% fee as i use coinbase.

This already available:
See here: https://github.com/MrPlusGH/NPlusMiner/blob/master/README.md

Per pools config (Advanced)

    - **This is for advanced users. Do not use if you do not know what you are doing.**
    - You can now set specific options per pool. For example, you can mine NiceHash on the internal wallet and other pools on a valid wallet. This configuration is provided as an example in Config\PoolsConfig-NHInternal.json
      - Available options
        - Wallet = your wallet address
        - UserName = your MPH user name
        - WorkerName = your worker name
        - PricePenaltyFactor = See explanation below
      - Usage
        - The file Config\PoolsConfig.json contains per pool configuration details. If a pool is listed in this file,
    the specific settings will be taken into account. If not, the setting for the entry name default will be used.
    **Do not delete the default entry.**
        - Edit Config\PoolsConfig.json
        - Add an entry for the pool you want to customize
          - The name must be the NPlusMiner name for the pool. ie. for ahashpool, if you use Plus. The name is ahashpoolplus.
          - (**careful with json formating **)
          - Best way is to duplicate the default entry
    - Note that the GUI only updates the default entry. Any other changes need to be done manualy

PricePenaltyFactor (Advanced)

    - When using advanced per pool configuration, it is possible to add a penalty factor for a specific pool. This simply adds as a multiplicator on estimations presented by the pool.
    - Example scenario
      - NiceHash as a 4% fee - Set PricePenaltyFactor to 0.96 (1-0.04)
      - You feel like a pool is exaggerating his estimations by 10% - Set PricePenaltyFactor to 0.9

[ubergod]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

[prvs]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

I confirm this error, however, this error occurs when the miners are first started, if they are stopped and restarted, everything is fine, and it was with earlier versions of 2.5...

[ubergod]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

I confirm this error, however, this error occurs when the miners are first started, if they are stopped and restarted, everything is fine, and it was with earlier versions of 2.5...

Stoping and restarting does not fix the issue for me.

[squashen]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

I confirm this error, however, this error occurs when the miners are first started, if they are stopped and restarted, everything is fine, and it was with earlier versions of 2.5...

Stoping and restarting does not fix the issue for me.

Try stop, save config, restart the hole program. I have to do some times for other reasons.

[muilfa]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

Stop Nemos, close and start again. It helps me so much.


Try restarting Benchmark

[prvs]

Where can I change the port of the mining for the algorithm in the settings?

[rob3123]

https://gyazo.com/955124de35fd8e3e57d195ee71bcc104
Hello, why does it show that im loosing btc while mining ?

[MrPlus]

https://gyazo.com/955124de35fd8e3e57d195ee71bcc104
Hello, why does it show that im loosing btc while mining ?

A couple possible reasons:

1 - Zergpool is reporting wrong data through the API. It will correct over time. (This happens some time)
2 - Zergpool reviewed estimated values and your total earned goes down. (In this case you should see it on Zergpool website)

[MrPlus]

Where can I change the port of the mining for the algorithm in the settings?

You cannot, the pool provides it through the API.
If you're talking zergpool: https://bitcointalk.org/index.php?topic=2759935.msg34919344#msg34919344

[MrPlus]

3.1, trying to add in x16r to my list and when it starts the miner it's only using 2 of my 6 cards.
The GUI detected all 6 cards and I have it set to use all 6 cards. But the raven miner only wants to load 0,1.nothing else.

I confirm this error, however, this error occurs when the miners are first started, if they are stopped and restarted, everything is fine, and it was with earlier versions of 2.5...

This problem at first start will be fixed in the next version of NPlusMiner.

[Bit2017User]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

[Sackl]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

Are the Cards overclocked ?

With Version 3.1 i had to reduce my Afterburner Settings to +100 Core to get it stable.

Even on Reference-Style  1080 TI & 1070 TI

[Bit2017User]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

Are the Cards overclocked ?

With Version 3.1 i had to reduce my Afterburner Settings to +100 Core to get it stable.

Even on Reference-Style  1080 TI & 1070 TI

Thanks
Will try to reduce a bit, they are at 75+300
Will see

[JCS-CCT]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

Are the Cards overclocked ?

With Version 3.1 i had to reduce my Afterburner Settings to +100 Core to get it stable.

Even on Reference-Style  1080 TI & 1070 TI

Thanks
Will try to reduce a bit, they are at 75+300
Will see

Try 80/50/600

This may help: https://github.com/MrPlusGH/NPlusMiner-Documentation/wiki/Overclocking-and-Prerun

[Bit2017User]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

Are the Cards overclocked ?

With Version 3.1 i had to reduce my Afterburner Settings to +100 Core to get it stable.

Even on Reference-Style  1080 TI & 1070 TI

Try 80/50/600

This may help: https://github.com/MrPlusGH/NPlusMiner-Documentation/wiki/Overclocking-and-Prerun

Thanks
Will try to reduce a bit, they are at 75+300
Will see

Thanks
Moved to 100 power ( no cost for me :-) ) + 50 core and 300 mem.
Will see if it's chosen to run again.

[Lukras]

what needs to be corrected so that cryptonight correctly shows  USD/DAY

Code:

Miner                   Algorithm           Speed mBTC/Day BTC/Day USD/Day BTC/GH/Day Pool
-----                   ---------           ----- -------- ------- ------- ---------- ----
ccminerCryptonight      CryptoNightV7 106,09 KH/s   22,740 0,02274 189,441  214,35510 nicehash-
ccminerCryptonight      CryptoNight   107,43 KH/s    3,184 0,00318  26,529   29,64193 nicehash-
ccminerTpruvotcuda9     HMQ1725         6,27 MH/s    0,476 0,00048   3,968    0,07599 zergpool-
ccminerAlexis78keccakc  Keccakc       995,76 MH/s    0,474 0,00047   3,953    0,00048 zergpool-
ccminerAlexis78         Lyra2RE2       53,79 MH/s    0,363 0,00036   3,028    0,00676 zpool-
ccminerAlexis78         Hsr            16,73 MH/s    0,346 0,00035   2,885    0,02070 zergpool-
ccminerAlexis78         X17            14,59 MH/s    0,312 0,00031   2,602    0,02140 zergpool-
ccminerAlexis78x16rx16s X16r           14,30 MH/s    0,301 0,00030   2,510    0,02106 zergpool-
DSTM                    Equihash      643,93  H/s    0,287 0,00029   2,391  445,75098 nicehash-
ccminerSuprminer        X16s           13,19 MH/s    0,285 0,00029   2,375    0,02162 zergpool-
ccminerAlexis78x16rx16s X16s           13,12 MH/s    0,284 0,00028   2,363    0,02162 zergpool-
ccminerAlexis78         Skein         678,21 MH/s    0,283 0,00028   2,361    0,00042 zergpool-
ccminerKlausT           NeoScrypt       1,44 MH/s    0,283 0,00028   2,361    0,19625 zpool-

[Bit2017User]

Hello
For me on zerg:3663 x16s is failing on 1080Ti
with the master from 2 days ago.
Thanks

Are the Cards overclocked ?

With Version 3.1 i had to reduce my Afterburner Settings to +100 Core to get it stable.

Even on Reference-Style  1080 TI & 1070 TI

Try 80/50/600

This may help: https://github.com/MrPlusGH/NPlusMiner-Documentation/wiki/Overclocking-and-Prerun

Thanks
Will try to reduce a bit, they are at 75+300
Will see

Thanks
Moved to 100 power ( no cost for me :-) ) + 50 core and 300 mem.
Will see if it's chosen to run again.

Sorry, but no X16S still not working on 1080TI and with the latest Suprminer not working on 1050TI
Will update to the latest master on 1080TI and try.

[BitBustah]

After months of doing nothing I booted the old mining rig.

What happend to the good 'ol Nemos? The GUI version is so laggy. Laggy, not buggy.

Is there a way to turn off the gui?