Keefe
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 23, 2013, 05:56:29 AM |
|
What is your average daily BTC earning for a single Chili right now?
7*24H=100G/0.09-0.08btc you can do math So about .03BTC/unit/day. Thanks! After tooling around with cooling a few days I have my 2 miners putting out approximately 72 GH/S combined. That is netting .066 BTC/day on BTCGUild. My goal is .2 BTC/day... so I need another 160 GH/S or so... I have 65 GH/S on the way... so I need 100GH/S. Do you guys have a suggestion of good hardware for this? Chilis are gone... so time to look for something else. Would you be interested in more Chilis? I have 8 in hand with coolers already mounted, that I'm willing to sell for 1.1 BTC each.
|
|
|
|
ipxtreme
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 23, 2013, 10:36:58 PM |
|
I am new to The Chili and I have tried BFGMINER and CGMINER in Windows and it still cant find the device. What drivers do I need to get it recognized?
What should the command line look like to run it on a pool?
Thx in advance
|
BTC tips: 14PkHaJH5GexLG9P7MYxHRNvZeCq2t8DWX
|
|
|
Keefe
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 23, 2013, 10:42:38 PM |
|
I am new to The Chili and I have tried BFGMINER and CGMINER in Windows and it still cant find the device. What drivers do I need to get it recognized?
What should the command line look like to run it on a pool?
Thx in advance
I think BFG works fine in windows with the FTDI driver. Did you wait for the LEDs to go out before starting BFG/CG?
|
|
|
|
oldbushie
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 94
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 02:44:56 AM |
|
When will I be able to run the Chilis in EasyMiner on an Android device? Or can they run in that already? I thought maybe a firmware upgrade would be needed due to what happened with first run Chilis (needing custom BFGMiner).
|
|
|
|
jelin1984
Legendary
Offline
Activity: 2408
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 03:00:44 AM |
|
I have one chilli for sell
|
|
|
|
Swimmer63
Legendary
Offline
Activity: 1593
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 03:20:34 AM Last edit: November 24, 2013, 03:38:17 AM by Swimmer63 |
|
I have one chilli for sell
Do you have it in hand? Where are you shipping from? EDIT: Picture too would be helpful.
|
|
|
|
bobsag3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 03:36:54 AM |
|
I would be happy to take unwanted chillis, But paying in fiat
|
|
|
|
ipxtreme
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 04:43:34 AM |
|
I am new to The Chili and I have tried BFGMINER and CGMINER in Windows and it still cant find the device. What drivers do I need to get it recognized?
What should the command line look like to run it on a pool?
Thx in advance
I think BFG works fine in windows with the FTDI driver. Did you wait for the LEDs to go out before starting BFG/CG? thanks. I got it working replacing the FTDI driver with a WinUSB driver from the cgminer recommendation deep on the forum. I will post the link when I find it again.
|
BTC tips: 14PkHaJH5GexLG9P7MYxHRNvZeCq2t8DWX
|
|
|
nexus99
Legendary
Offline
Activity: 910
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 11:00:04 AM |
|
I am new to The Chili and I have tried BFGMINER and CGMINER in Windows and it still cant find the device. What drivers do I need to get it recognized?
What should the command line look like to run it on a pool?
Thx in advance
I think BFG works fine in windows with the FTDI driver. Did you wait for the LEDs to go out before starting BFG/CG? thanks. I got it working replacing the FTDI driver with a WinUSB driver from the cgminer recommendation deep on the forum. I will post the link when I find it again. Once you install the FTDI driver you can use zadig to swap it so you can swap between the 2 mining apps.
|
|
|
|
Olly_K
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 12:58:27 PM |
|
|
|
|
|
Olly_K
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 05:02:40 PM |
|
getting a few questions via PM so though I would post here again. The CPU cooler I'm using is a "Enermax T60-VD Vegas Top-Down CPU Cooler" Pics of the underside of the board and also a closer pic of the mounting method. Just 30mm M3 bolts with M3 flange nuts: ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.ollyk.com%2Fmining%2Fchilibottom.jpg&t=665&c=D7hdjPOj_uzW3Q) ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.ollyk.com%2Fmining%2Fchilimounting.jpg&t=665&c=rbqAFJLS9Nbp7g)
|
|
|
|
jheaton
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 08:49:20 PM Last edit: November 24, 2013, 09:35:40 PM by jheaton |
|
Hi everyone! First post outside of newbie section. Need a little help with a chili. Ive read through this whole thread a couple times and still can not solve my problems. I left out configurations since I have 2 60ghz singles and 1 working chili so all is good there.
Basically I have 2 chili's, the first runs great (after the 7&8 led's finally stop, sometimes blink for hours.) The second is my concern. When I plug it in LED's 5,6,7,8 come on and stay on for about 4 seconds, then LED's 1 and 3 come on (for 2 or 3 seconds), after that #7 just sits and blinks very slow about 2 sec. lit up 2 sec. off… Eventually #8 lights up and they both shut off. I guess this is a normal led routine other than very very slow. I have flashed "both" to the 14d I think, no changes. Hashes about 9 ghz? (and check this out, when first plugged in, no LED's will come on and start their thing until I physically touch the LED lights with my finger. wtf..lol)
Any suggestions would be great!
Thanks in Advance!!
|
|
|
|
i3luefire
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 86
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 09:54:37 PM |
|
Hi everyone! First post outside of newbie section. Need a little help with a chili. Ive read through this whole thread a couple times and still can not solve my problems. I left out configurations since I have 2 60ghz singles and 1 working chili so all is good there.
Basically I have 2 chili's, the first runs great (after the 7&8 led's finally stop, sometimes blink for hours.) The second is my concern. When I plug it in LED's 5,6,7,8 come on and stay on for about 4 seconds, then LED's 1 and 3 come on (for 2 or 3 seconds), after that #7 just sits and blinks very slow about 2 sec. lit up 2 sec. off… Eventually #8 lights up and they both shut off. I guess this is a normal led routine other than very very slow. I have flashed "both" to the 14d I think, no changes. Hashes about 9 ghz? (and check this out, when first plugged in, no LED's will come on and start their thing until I physically touch the LED lights with my finger. wtf..lol)
Any suggestions would be great!
Thanks in Advance!!
I think 14e is the newest FW. it is on here somewhere but i am not sure which page. what size of a PSU are you running and what all is on it besides the 2 chili's?
|
|
|
|
i3luefire
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 86
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 10:00:21 PM |
|
BTW everyone. i hooked up a Chili today with the 12v and gnd swapped. ![Embarrassed](https://bitcointalk.org/Smileys/default/embarrassed.gif) we were trying out a setup where all the PSUs were hooked up with combined 12v rails. we plugged in the stupid cpu 12v supply without swapping the polarity. it fried 2 PSUs. but the Chili seems to have survived somehow. now we can only run 11 of our 13 miners until we get our new PSUs from newegg. be careful out there with the cpu power plug.
|
|
|
|
nexus99
Legendary
Offline
Activity: 910
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 10:07:47 PM |
|
Hi all,
How much wattage is each chili pulling for you guys?
|
|
|
|
i3luefire
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 86
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 10:26:00 PM |
|
Hi all,
How much wattage is each chili pulling for you guys?
im getting about 220w per miner at the wall for the ones over 35gh.
|
|
|
|
jheaton
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 11:11:51 PM |
|
Hi everyone! First post outside of newbie section. Need a little help with a chili. Ive read through this whole thread a couple times and still can not solve my problems. I left out configurations since I have 2 60ghz singles and 1 working chili so all is good there.
Basically I have 2 chili's, the first runs great (after the 7&8 led's finally stop, sometimes blink for hours.) The second is my concern. When I plug it in LED's 5,6,7,8 come on and stay on for about 4 seconds, then LED's 1 and 3 come on (for 2 or 3 seconds), after that #7 just sits and blinks very slow about 2 sec. lit up 2 sec. off… Eventually #8 lights up and they both shut off. I guess this is a normal led routine other than very very slow. I have flashed "both" to the 14d I think, no changes. Hashes about 9 ghz? (and check this out, when first plugged in, no LED's will come on and start their thing until I physically touch the LED lights with my finger. wtf..lol)
Any suggestions would be great!
Thanks in Advance!!
I think 14e is the newest FW. it is on here somewhere but i am not sure which page. what size of a PSU are you running and what all is on it besides the 2 chili's? I have 2 1000w PS's, the fans hardly even have to spin up. I can swap the good one with the bad one with the same configuration and its the chili. Has no one heard of the LED sequence running super slow?
|
|
|
|
nexus99
Legendary
Offline
Activity: 910
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 24, 2013, 11:53:07 PM |
|
Hi all,
How much wattage is each chili pulling for you guys?
im getting about 220w per miner at the wall for the ones over 35gh. Sounds like a 1000 watt PSU can safely handle 4.
|
|
|
|
MrTeal (OP)
Legendary
Offline
Activity: 1274
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2013, 12:25:44 AM |
|
Hi all,
How much wattage is each chili pulling for you guys?
im getting about 220w per miner at the wall for the ones over 35gh. Sounds like a 1000 watt PSU can safely handle 4. I'm running 4 on an 850W HEC supply ( http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=7621664&CatId=2534) I got for $30 after MIR, and each is running 35GH/s plus. They'd actually be running faster, but they're in my office and after a weekend of 800W of heat load in a small closed room it's going to be 35C in there when I get to work on Monday.
|
|
|
|
Choadmeyer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
November 25, 2013, 01:07:42 AM |
|
My chili is running at 28.5 GH/s at 63C using BFGminer 3.6 with an Evo 212 cooler. I have a high speed duct fan blowing on both bottom and top of my setup.
Fishing for any ideas to help me step my speed up (seems like I'm missing out on at least 5 GH/s).
Thanks in advance people.
|
|
|
|
|