[ANN] Ravencoin [RVN] PoW GPU Mining | Asset Transfer Blockchain (Updated ANN)

[shenery]

So I have my 1060 3gb's running at +150 core and +50 memory. That was the only way I could make it stable. Also running them at 85w a card. Temps sitting at between 70 and 75 degrees c. Are these temps ok? Also are the watts ok? I have 2 cards per vga port on my 750w psu.

Kind regards
Steven

Edit fans are at 100%

What brand are those 1060's? Zotac mini crap? Seemed too hot to me considering that the fans are running at full power. I mean 75 degrees C are OK but not while having the fans at full speed. Your fans will probably die before your cards do.

Other than that, you are doing OK. You may try to run at %80 Power LvL also. Did you test at a lower lvl? Might help with the temperature too.

They are inno3d single fan. Was the first reasonable priced cards I saw since the drought. They all have Samsung memory though.
I had it running at 65w but increased to see if I would get better hashrate. I will try 80w and see how that goes.

I have my target temperature set I'm smos to 69c. If I increase the target temperature surely my fan speed will come down no?

[1714832315]

1714832315

[1714832315]

1714832315

[1714832315]

1714832315

[mindrust]

So I have my 1060 3gb's running at +150 core and +50 memory. That was the only way I could make it stable. Also running them at 85w a card. Temps sitting at between 70 and 75 degrees c. Are these temps ok? Also are the watts ok? I have 2 cards per vga port on my 750w psu.

Kind regards
Steven

Edit fans are at 100%

What brand are those 1060's? Zotac mini crap? Seemed too hot to me considering that the fans are running at full power. I mean 75 degrees C are OK but not while having the fans at full speed. Your fans will probably die before your cards do.

Other than that, you are doing OK. You may try to run at %80 Power LvL also. Did you test at a lower lvl? Might help with the temperature too.

They are inno3d single fan. Was the first reasonable priced cards I saw since the drought. They all have Samsung memory though.
I had it running at 65w but increased to see if I would get better hashrate. I will try 80w and see how that goes.

Memory brand don't affect Raven hashrate at all. It is not like ETH.

My prediction was close enough, your cards are mini type/single fan cards. Those usually are known for dying faster than the bigger/2 fan models. I would keep them cool.

[BiteByte]

It can be said based on circulating supply that RVN coin is undervalued. After few sessions of mini corrections it has found new floor at current price. It seems that market will gain huge share suddenly taking off and not watching back whenever this happens. This sleeping giant can be next big thing to surprise unaware people.

Your words give me warm fuzzies sir, and I agree with you wholeheartedly.

[juhakall]

I just realized that the transaction fees on Raven are so absurdly low, there's nothing stopping my pool from paying out every 420 seconds (7 minutes). There's also no fee.

http://rvn.elitehash.net

[cryptodunno]

So I have my 1060 3gb's running at +150 core and +50 memory. That was the only way I could make it stable. Also running them at 85w a card. Temps sitting at between 70 and 75 degrees c. Are these temps ok? Also are the watts ok? I have 2 cards per vga port on my 750w psu.

Kind regards
Steven

Edit fans are at 100%

What brand are those 1060's? Zotac mini crap? Seemed too hot to me considering that the fans are running at full power. I mean 75 degrees C are OK but not while having the fans at full speed. Your fans will probably die before your cards do.

Other than that, you are doing OK. You may try to run at %80 Power LvL also. Did you test at a lower lvl? Might help with the temperature too.

They are inno3d single fan. Was the first reasonable priced cards I saw since the drought. They all have Samsung memory though.
I had it running at 65w but increased to see if I would get better hashrate. I will try 80w and see how that goes.

i suggest you need tp decrease power limit to lower the temps.
75C is very high, I`ve heard a lot of times that it`s not recomended to run GPUs over 70C for 24/7, as there is a chance to kill your GPU very fast

[Random-Reboot]

So I have my 1060 3gb's running at +150 core and +50 memory. That was the only way I could make it stable. Also running them at 85w a card. Temps sitting at between 70 and 75 degrees c. Are these temps ok? Also are the watts ok? I have 2 cards per vga port on my 750w psu.

Kind regards
Steven

Edit fans are at 100%

What brand are those 1060's? Zotac mini crap? Seemed too hot to me considering that the fans are running at full power. I mean 75 degrees C are OK but not while having the fans at full speed. Your fans will probably die before your cards do.

Other than that, you are doing OK. You may try to run at %80 Power LvL also. Did you test at a lower lvl? Might help with the temperature too.

They are inno3d single fan. Was the first reasonable priced cards I saw since the drought. They all have Samsung memory though.
I had it running at 65w but increased to see if I would get better hashrate. I will try 80w and see how that goes.

I use the Curve function in the Core Clock in Afterburner menu. The voltage is fixed at 800mV, the frequency of three video cards is from 1645 to 1759 MHz (matched to stability after stress tests). Single-fan MSI GTX1060 Aero 3Gb, temperatures up to 61 degrees in a closed case CM Haf X. Hashrate approximately 5 MH / s per card, z-enemy 1.08. Screenshot of AfterBurner in the attachment. I apologize for my English.
https://yadi.sk/i/0KLR5rYP3VaXgY

[wangxueipod]

My Rvn has been lost in my wallet. Is there any way?

[Steamtyme]

My Rvn has been lost in my wallet. Is there any way?

What do you mean exactly? The wallet you mine to or sent your bought raven now has a 0 balance?

Or were you keeping it on an exchange?

If it is your wallet you can check the transactions to see if the coins were sent. Is there a chance someone had access to your wallet and your password?

Do you have a back up of your wallet.dat file?

[djgfla]

This is the video that helped me. 

https://youtu.be/RrDWFMuXOXI

It is a very disturbing feeling thinking that you have lost access to your wallet.  I went through this last week; if you check a few pages back there are some answers to a similir question that I asked. 

Luckily I had my wallet.dat file that I had backed up two days previously.  Without that I would have had to rely on the wallet.dat file that was on my computer and possibly corrupted.

[chem612]

This is the video that helped me. 

https://youtu.be/RrDWFMuXOXI

It is a very disturbing feeling thinking that you have lost access to your wallet.  I went through this last week; if you check a few pages back there are some answers to a similir question that I asked. 

Luckily I had my wallet.dat file that I had backed up two days previously.  Without that I would have had to rely on the wallet.dat file that was on my computer and possibly corrupted.

Gotta make multiple copies on different devices offline lol

[Novicracker]

Hey guys I'm trying to get a few Legacy Cards running. I admit they are old but should run on RVN. I have a GTX 760 2g, 2 GT 610's 2g's. I have been searching for a Miner that has these cards in their compatibility range but with no avail. I'm wanting to run these cards into the ground so I can buy a much better cards to take their place. is there any advice as where I can get some mining soft that will work?

[mindrust]

Hey guys I'm trying to get a few Legacy Cards running. I admit they are old but should run on RVN. I have a GTX 760 2g, 2 GT 610's 2g's. I have been searching for a Miner that has these cards in their compatibility range but with no avail. I'm wanting to run these cards into the ground so I can buy a much better cards to take their place. is there any advice as where I can get some mining soft that will work?

Selling them would be a better choice (if you are lucky enough to find a buyer) than running them at this point. They are too outdated. The amount of electricity they'll be burning will be more than what you pay for the coins directly.

They probably don't even have the hashrate power to generate coins.

[platinum4]

Hey guys I'm trying to get a few Legacy Cards running. I admit they are old but should run on RVN. I have a GTX 760 2g, 2 GT 610's 2g's. I have been searching for a Miner that has these cards in their compatibility range but with no avail. I'm wanting to run these cards into the ground so I can buy a much better cards to take their place. is there any advice as where I can get some mining soft that will work?

Selling them would be a better choice (if you are lucky enough to find a buyer) than running them at this point. They are too outdated. The amount of electricity they'll be burning will be more than what you pay for the coins directly.

They probably don't even have the hashrate power to generate coins.

Could see if they run x17 on an old alexis miner

[xpoolx]

Hi Ravencoin forum.

We're glad to announce we have been added RVN to our pool.

Webpage: http://xpoolx.com/ravindex.php?page=dashboard
0% fees
1000 RVN reward bonus for first 20 blockfinders
Online chat.
24/7 support: Contact at info@xpoolx.com

We are configuring some parameters on the pool like the hashrate to adjust to the real hashrate but we need some miners to for testing and finish it.

[juhakall]

I made a thread for the new RVN PPS pool. It's being run by the CryptoHashTank/Elitehash team. Welcome!

https://bitcointalk.org/index.php?topic=3687463.0

[WickedPigeon]

Enemy - Today at 2:00 PM on Discord
Z-ENEMY VER 1.09a ( PUBLIC )

For Windows (Cuda 9.1)
zealot/enemy-1.09a (z-enemy)  From: Dk & Enemy

- Kernels speed improvements 1.08 vs 1.09a, for all 9x0 and 10x0 GTX:
 x16r +5-8%, x16s +5-10%, bitcore +5-8%, xevan +5-20% ( vs basic public), phi + 2-3%, x17 (basic), vit (new algo).

- Support new algos : Xevan (-a xevan) and Vitality (-a vit), recommended intensity for Xevan 19-20, for Vitality 19-21

- "Search mode" is enabled on 1.09a! This means that if you use a low diff you may see extra shares come through on your miner. You may see something like "2 shares" or "3 shares", up to 10+. This is a BONUS!.If you can find more than one share on your scan range you’ll find them all.If you have a bigger farm and use a higher diff you may also see the double or triple shares ,but it will be more rare. I still advise larger farms to continue to use higher diff.

- Revised dev-fee mechanism. Now the miner does not break off connection with a pool and does not drop work of video cards. Everything works without switch-offs.

- Now supporting failover pool! It is now possible to add additional pools incase your main pool loses stratum connection. Here is an example for your .bat file:
z-enemy -a x16r -o stratum+tcp://ravenminer.com:6666 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=16 -o stratum+tcp://krawww-miner.eu:3636 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=3

- Duplicate output into log file (-l, --log=logfile.txt )

- Better error reporting. Now you see device number with its name if you encounter any cuda errors.

- Pool latency. When submitting shares now you see pool's response time in milliseconds.

https://mega.nz/#!RaBEELza!p4mtA2Ullr4V4Ocd-siNAaxZYHXmDhGQvC0ztYgTuQE


Linux ( Hive OS, Ubuntu ) Z-ENEMY VER 1.09a  ( PUBLIC )
Cuda 8.0
https://mega.nz/#!VDBEhYAI!j-WB0FzmyO3sBG_NXlmSI7apD89zmUHpgGdZpoAkRNQ
Cuda 9.0
https://mega.nz/#!cDhgGBZS!DKsdS6HdgBr8-O2qvYkKnOya_RiY-N5-xTCwSqcY8_w
Cuda 9.1
https://mega.nz/#!VSY3QAQT!xnJ1e2lMgBKYPY_ytipNtEjpCTkWkj-UmJRcUJzWPBE

[Marvell2]

we need a new exchange , i sent 12k raven from my personal wallet to cryptobridge as a test and the charged 200 raven as a FEE!

my balance on the exchange was only 11799 after their fee

stay far away from this scummy exchange

[crypto4pizza]

we need a new exchange , i sent 12k raven from my personal wallet to cryptobridge as a test and the charged 200 raven as a FEE!

my balance on the exchange was only 11799 after their fee

stay far away from this scummy exchange

Did you make 2 deposits within 1 hr?  They charge 2% for that. 

[Marvell2]

Enemy - Today at 2:00 PM on Discord
Z-ENEMY VER 1.09a ( PUBLIC )

For Windows (Cuda 9.1)
zealot/enemy-1.09a (z-enemy)  From: Dk & Enemy

- Kernels speed improvements 1.08 vs 1.09a, for all 9x0 and 10x0 GTX:
 x16r +5-8%, x16s +5-10%, bitcore +5-8%, xevan +5-20% ( vs basic public), phi + 2-3%, x17 (basic), vit (new algo).

- Support new algos : Xevan (-a xevan) and Vitality (-a vit), recommended intensity for Xevan 19-20, for Vitality 19-21

- "Search mode" is enabled on 1.09a! This means that if you use a low diff you may see extra shares come through on your miner. You may see something like "2 shares" or "3 shares", up to 10+. This is a BONUS!.If you can find more than one share on your scan range you’ll find them all.If you have a bigger farm and use a higher diff you may also see the double or triple shares ,but it will be more rare. I still advise larger farms to continue to use higher diff.

- Revised dev-fee mechanism. Now the miner does not break off connection with a pool and does not drop work of video cards. Everything works without switch-offs.

- Now supporting failover pool! It is now possible to add additional pools incase your main pool loses stratum connection. Here is an example for your .bat file:
z-enemy -a x16r -o stratum+tcp://ravenminer.com:6666 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=16 -o stratum+tcp://krawww-miner.eu:3636 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=3

- Duplicate output into log file (-l, --log=logfile.txt )

- Better error reporting. Now you see device number with its name if you encounter any cuda errors.

- Pool latency. When submitting shares now you see pool's response time in milliseconds.

https://mega.nz/#!RaBEELza!p4mtA2Ullr4V4Ocd-siNAaxZYHXmDhGQvC0ztYgTuQE


Linux ( Hive OS, Ubuntu ) Z-ENEMY VER 1.09a  ( PUBLIC )
Cuda 8.0
https://mega.nz/#!VDBEhYAI!j-WB0FzmyO3sBG_NXlmSI7apD89zmUHpgGdZpoAkRNQ
Cuda 9.0
https://mega.nz/#!cDhgGBZS!DKsdS6HdgBr8-O2qvYkKnOya_RiY-N5-xTCwSqcY8_w
Cuda 9.1
https://mega.nz/#!VSY3QAQT!xnJ1e2lMgBKYPY_ytipNtEjpCTkWkj-UmJRcUJzWPBE

great work, thank you for failover

[Marvell2]

we need a new exchange , i sent 12k raven from my personal wallet to cryptobridge as a test and the charged 200 raven as a FEE!

my balance on the exchange was only 11799 after their fee

stay far away from this scummy exchange

Did you make 2 deposits within 1 hr?  They charge 2% for that. 

I had a smaller one of 4999 from another wallet , basically just testing to see how easy it is to move stuff back an forth yes

200 raven for one deposit is pure highway robbery