[www.easy2mine.com] 340$, the group buy of antminer s5(psu included)

[pcfli]

we are opening remote access to hosted dragon these days, and the miner will offline for several hours to update the firmware, i have sent a mail in advance and maybe that lead to the problem

are you going to make that new firmware available to all customers who have purchased miners from you in the past?  i'd love to get a better/up-to-date firmware

thanks for your trust, we didnot add anything but only remote access system, if you want open remote access to your miner please pm me and i will update it

[1714154989]

1714154989

[1714154989]

1714154989

[finlof]

we are opening remote access to hosted dragon these days, and the miner will offline for several hours to update the firmware, i have sent a mail in advance and maybe that lead to the problem

are you going to make that new firmware available to all customers who have purchased miners from you in the past?  i'd love to get a better/up-to-date firmware

thanks for your trust, we didnot add anything but only remote access system, if you want open remote access to your miner please pm me and i will update it

no i'm ok.  i have them locally and when i'm not local I have access via VPN.  thanks.

[nzgrant]

I have a problem

Dragon arrived today so I set it up and powered it up changed gateway ip and setup pool info but it wouldnt mine. Fans were going and green lights on blades were on but red led on front was not on.
So I took side off and checked all cables were plugged in properly put side back on and powered up.

Now I cant get to it via the web interface no blade green lights are on the fans are going and now the red led on the front is on.

any thoughts ?


I removed the PI and it works fine away from the dragon but doesn't power up when in the dragon.

Can anyone think of anything but the control board is stuffed ?  There is a ribbon cable that goes from the board to the PI which I assume powers the Pi as well as comms.

[nzgrant]

pcfli

help needed please.  I have emailed you also.

[nzgrant]

update

I tried the control board from another dragon and still nogo.

I plugged the lcd screen from the old dragon onto the control board(new dragon doesnt't have a screen) and the new dragon powered up but still wouldnt mine.
The pool addresses are the same in both dragons

this is so frustrating the last dragon took about 15 minutes to get going.


Any ideas

[arczi19]

Hello,
How much for the 30M miner?

[Easy2Mine]

update

I tried the control board from another dragon and still nogo.

I plugged the lcd screen from the old dragon onto the control board(new dragon doesnt't have a screen) and the new dragon powered up but still wouldnt mine.
The pool addresses are the same in both dragons

this is so frustrating the last dragon took about 15 minutes to get going.


Any ideas

Use an IP scanner to scan the IP of the dragon.
Log into the web based interface and press ok to start automatically.
If you change the IP, the Dragon needs about 2 minute to start for the first time at the new IP.
If this didn't solve your problems, then look at the inside of the Dragon.
If you see 1 PCI-E cable or power cable that splits into 2 PCI-E connector.
Than you got a model with less powerfull PSU.
When these PSU are new, they can mine for a while, after a few weeks of mining these PSU died a bit and won't power up the Dragon enough.
Replace with a better PSU and make sure each module of the Dragon is separately powered by 1 PCI-E cable.
Do not use a cable that splits into 2 connectors.
Make sure the motherboard cable is plugged into the control board.

I hope this help.

[muzzyshop]

Hi,
I just open "Dragon 1T" team at Btcguild.
Feel invited

[nzgrant]

The plot thickens

If I use the sd card from my old dragon and plug the lcd screen from it also into the new dragon then the new one mines happily.

Does anyone have instructions to create a new sd card for the PI ?

And any ideas to get around needing the lcd screen ?

[nzgrant]

ok I have created a new sd card which works but only when the lcd screen from the old dragon is installed.

Anyone know how to simulate a screen being there ?

[nzgrant]

Does anyone have a sd card image from a dragon without a screen I could try ?

[pcfli]

Update 23 May
After testing for 12 hours, one of my A2 terminator-90 can perform stable 90M hash rate on pools
here is the test account if you want to see
http://www.f2pool.com/user/login
user:pcfli1@126.com
pass:1234567u

BTW, i have two unit of A2 terminator-90 in my data center and can switch to work for you within 12 hours
Price: 11299$
60% payment to get it work for you and pay the rest 40% within 15 days
all the customer who have bought dragon from me can get 200$ discount on these miner
and all the customer who have bought A2 terminator-90 can get 400$ discount

[muzzyshop]

Hi Lee,
Please Kindly reply to my message
Thank You

[pcfli]

where should i reply

[muzzyshop]

where should i reply

when my new miner will be online.
May 21, 2014
PayPal Transaction ID:
4AF34709893747325

And I want to know your western union details to pay for one more miner
Thank You!

[pcfli]

Pls delete

[bilabonic]

Payment sent for x1 - Dragon 1Th miner....

[pcfli]

Pls delete

[nzgrant]

a happy miner here. pcfli sent me an lcd screen and now the new dragon is up and mining.

Thanks for the help pcfli.  

Saving up for the next one now

[muzzyshop]

Is there any available on professional data center